amazon basics B010QZD616 Notebook Laptop Stand Arm Mount Tray User Manual

amazon basics B010QZD616 Notebook Laptop Stand Arm Mount Tray

Package Contents

Before getting started, ensure the package contains the following components:

You will need

IMPORTANT SAFEGUARDS

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.

When using the product, basic safety precautions Should always be followed to reduce the risk of injury including the following:

This product will need tension adjustments after installation is complete. Make sure that all equipment is properly installed on the product before attempting a range of motion or tension adjustments. Any time equipment is added or changed on this product resulting in a different mounted weight, you should repeat the adjustment steps to ensure state and optimum operation. This product should move smoothly and easily through the full range of motion and stay where you set it. If movement is difficult or the product does not stay where you set it, follow the adjustment instructions to loosen or tighten the tension to create a smooth, easy motion. Depending on your product and the adjustment, it may take many turns to notice a difference.

Before First Use

Check for transport damages.

DANGER
Risk of suffocation!

Keep any packaging materials away from children — these materials are a potential source of danger. e.g. suffocation.

Assembly

• Step 1: Lock the arm orientation

  • On your existing mount arm, insert the M3 x 6 mm screw into the front of the plate to lock its orientation.

• Step 2: Attach the notebook tray

  • Attach the notebook tray to the mounting plate with either the M4 x 10 mm
    screws and a screwdriver or the M4 x 10 knobs. Hand-tighten the knobs.

• Step 3: Determine the connection method
  You can place your notebook:

  • Directly on the notebook tray.
  • On a docking station (not included) that is mounted to the notebook tray.

Notebook tray

• Step A: Remove the backing from the non-slip pads, then place them on the notebook tray (as shown).
• Step B: Loosen the adjustment knobs underneath the notebook tray to adjust the length of the notebook tray legs, and place the notebook on the tray. Then tighten to secure. Your notebook should fit snugly against the notebook tray legs.
• Step C: See “Step 4: Adjust your ams tension” on page 8 to adjust your notebook arms tension.

Docking station

• Step A: Cut the non-slip pads in half, remove the backing, then place them on the notebook tray (as shown).

• Step B: Remove the backing from the three adhesive strips on the notebook tray, then firmly press your docking station onto the strips. The back of the docking station should be flush with the back of the notebook tray.

• Step C: Loosen the adjustment knobs underneath the notebook tray to adjust the length of the notebook tray legs, and place the notebook on the tray. Then tighten to secure. Your notebook should fit snugly against the notebook tray legs.

• Step D: Measure a small, medium, and large hook against the back of the notebook tray and docking station then pick the hook that fits around it best. One at a time, loosen the top mounting screws on the arm. then slide the hook around the screw and your docking station. Tighten the mounting screw to hold the hook in place.
  NOTICE
  You can also remove a mounting screw to attach the cable clip.

• Step 4: Adjust the mounting arm tension

Adjust your notebook mount tension. You can adjust the vertical. tilt, and arm tension so that the notebook stays in place when you move it.

Adjustment

Adjusting the vertical tension
Tilt the notebook down to access the screw. If the notebook is rising, loosen the screw by turning it to the left. If the notebook is falling, tighten the screw by turning it to the right.

CAUTION
Do not over-tighten the screw. You might damage your notebook mount.

Adjusting the tilt tension

• CAUTION DO not remove the screw. The notebook tray might fall.
• CAUTION DO not over-tighten the screw. You might damage your notebook mount.

Warranty Information

To obtain a copy of the warranty for this product:

• US: amazon.com/AmazonBasics/Warranty.
• UK: amazon.co.uk/basics-warranty.
• US: +1-866-216-1072
• UK: +44 (0) 800-279-7234

Feedback and Help
Love it? Hate it? Let us know with a customer review. AmazonBasics is committed to delivering customer-driven products that live up to your high standards. We encourage you to write a review Sharing your experiences with the product.

• US: amazon.com/review/review-your-purchases#
• UK: amazon.co.uk/review/review-your-purchases#
• US: amazon.com/gp/help/customer/contact-us
• UK: amazon.co.uk/gp/help/customer/contact-us.
• amazon.com/AmazonBasics.

MADE IN CHINA.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>