Baseus Technology BS-CW02 Baseus MagPro Series Magnetic Wireless Charging Car Mount User Manual
- June 15, 2024
- Baseus Technology
Table of Contents
User Manual
BS-CW02 Baseus MagPro Series Magnetic Wireless Charging Car Mount
Baseus MagPro Series Magnetic Wireless Charging Car Mount 15SW
Please read this user manual carefully before use and keep for future
reference.
Installation
- Clip the tail clamp onto the most suitable spot of the air vent
- Place the phone with magnet plate into the mount
Magnet Plate Installation
- Align the positioning liner with the back of your phone, and find the spot for wireless charging
- Stick the magnet plate onto your phone’s back
Product Introduction
This product is a wireless charging car mount that comes with cooling function.
Product Specifications
Name: Baseus MagPro Series Magnetic Wireless Charging Car Mount 15W
Model No.: BS-CW02
Input: 5V 2.4A (Max.} ; 9V 2.23A (Max.)
Wireless Charging Output: SW/7.5W/10W/15W
Total Power: 15W
Working Temperature: Non-tropical areas, 0°C to 35 °C
Accessories
USB-A to USB-C charging cable X 1
USB-C to USB-C charging caole X 1
Product Introduction
- Wireless charging area
- Cooling fan
- Tail clamp
- USB-C port
- Wireless cha-ging switch
Lighting Effect Instructions
Wireless charging 07: Indicator on
Wireless charging off: Indicator off
Attention
- This product is applicable to iP12 and above models, older iP models and Android models need to use with the metal plate;
- Please DO NOT use the product to charge phones with 6mm trick (or thicken) cases, for it may affect the charging efficiency.
- It is compatiole with Magsa‘e phone cases.
- This product supports15W wireless output, please use with a USB-C to USB-C 3A cable.
Declaration on hazardous substances and elements contained in electronic products
| Part Descrption | Hazardous substances and elements |
|---|---|
| Lead (pb) | Mercury (Hg) |
| (Cd) | Hexavalent |
chromium
(Cr VI)| Polybrominated
Biphenyls (PBB)| Polybrominated
Biphenyl ethers (PBDE)
PCB| X| 0| 0| 0| 0| 0
Plastic| 0| 0| 0| 0| 0| 0
Accessory| 0| 0| 0| 0| 0| 0
This form is compiled in accordance with SJ/T 11364.
O: It indicates that the content of the harmful substance in all homogeneous
materials of the component is below the limit specified in GB/T 26572
standard.
X: The content of harmful substances in at least one homogeneous material of
this part exceeds the limit stipulated in GB/T 26572 standard.
Warm Tip: The 5-year icon refers to the “effective life of environmental
protection”, not the product quality assurance period. Electronic products all
contain harmful substances such as lead, mercury and cadmium.
Once they are overused, harmful substances may leak or mutate, cause pollution
to the environment, or cause serious damage to people and property. The term
of “environmental protection use” means that all electronic products will be
required to use within this effective period. We will no longer be responsible
for the quality of the products due to the safety risks that arise after the
safe use period.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’ s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna. It is hereby declared that
this product model BS-CW0?2 of Shenzhen Baseus Technology Co., Ltd.,complies
with the provisions of Directive 2014/53/EUV, Directive 2011/65/EU. The full
text of the EC Declaration of Conformity can be found on the following
website: www.baseus.com
This equipment complies with the provisions of Directive 2012/19/EU. It is strictly forbidden to dispose of this equipment with ordinary trash; it must be recycled. This symbol indicates that the product shall not be treated as regular domestic trash, and must be delivered to a recycling center that is capable of recycling electronic and electrical equipment.
FCC 1D:2A482-BS-CWO02
Manufacturer: Shenzhen Baseus Technology Co., Ltd.
Add: 2™ Floor, Building B, Baseus Intelligence Park, No.2008, Xuegang Rd,
Gangtou Community, Bantian Street, Longgang District, Shenzhen Executive
Standard: Q/BASEUS 019
Hotline: 400-071-271 1{China) / +1 800 220 8056(Global)
Website: https://www.baseus.cn(China) / https://www.baseus.com(Global)
Official After-sales E-mail Address:
service@baseus.com (China) /
care@baseus.com (Global)
PB4633Z_POAO
1100006998
Designed by Baseus
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>