Smugdesk C-3595 Office Chair Ergonomic Mesh Chair Instruction Manual

Smugdesk C-3595 Office Chair Ergonomic Mesh Chair

Specifications

• Model: C-2577
• Weight Limit: 275 lbs

Product Usage Instructions

Assembly:

1. Insert Casters (F) into the Chair Base (E). Insert Gas Lift (D) into the hole in the center of the Chair Base (E).
2. Attach the Seat Mechanism (C) to the bottom of the Chair Seat (A) using Bolts (K) by Allen Wrench (H).
3. Attach the pre-assembled Chair Back & Armrest (B) to the Seat Mechanism (C) using Bolts (I) by Allen Wrench (H).
4. Position the assembled chair upright with the Seat Mechanism (C) facing down. Insert the Gas Lift (D) into the center hole of the Seat Mechanism(C) and press down until fully engaged.
5. Attach Headrest (G) to Chair Back (B) using Bolts (J) by Allen Wrench (H).

Instructions For Use

1. Operating the tilt lockout: To let your chair tilt back, pull the control handle out. To stop your chair from tilting, sit forward, then push the control handle in.
2. Tilt Tension: Use the long stem under the seat with a knob to adjust the tilt tension. Turn the knob forward (counter clockwise) to increase tension and backward (clockwise) to decrease tension.
3. Headrest: Move the headrest up/down to adjust the height and angle it up/down to the desired position.
4. Lumbar Support: Reach the lumbar support on the backside of the chair back and move it up/down to the desired position.
5. Seat Height: Use the paddle-shaped lever on the right side to adjust the seat height. Lift the lever up while taking your weight off the chair to raise it. Lift the lever up while seated to lower it. Ensure that your feet rest flat on the floor at the proper height.
6. Armrests adjustment: Press the button on the side of the armrest to adjust the height. Hold the armrest pads to adjust pad position: (1) move forward and backward, (2) move inward and outward, (3) pivot inward and outward. Hold the armrest pads to flip up/down the armrests.

Safety And Maintenance:

• Do not stand on the chair or use it as a stepladder.
• Use this product for seating one person at a time.
• Do not use the chair unless all bolts and screws are firmly secured.
• Avoid contact with sharp objects to prevent puncturing the fabric.
• Every 6 months, check all bolts and screws to ensure they are tight.
• To clean, spot clean only using a damp towel and mild cleaner.
  First, test on a small, unseen area of fabric.

FAQ:

Q: How much weight can this chair support?
A: The chair has a weight limit of 275 lbs.

Q: How should I clean the chair?
A: Spot clean the chair using a damp towel and mild cleaner.
Test on a small, unseen area of fabric first.

Q: How often should I check the bolts and screws?
A: It is recommended to check all bolts and screws every 6 months to ensure they are tight.

Model: C-2577

ASSEMBLY GUIDE

Congratulations, you are now the owner of the new chair!
Before enjoying the comfortable chair, you have to assemble it. This assembly guide will take you through the basic assembly process. To make sure your assembly progress goes smoothly, please follow the assembly instructions especially the important safety information.
It is possible to assemble the chair by your own, while having a second person to help you will make it easier.
Please check if there are any missing parts in the package before start. If there are any issues, please don’t hesitate to drop us an email and we’ll help you ASAP.
If you run into any difficulty during the assembly, remember to check out the assembly Video to see if you’ve missed something. If you’re still unable to resolve your problems , drop us an email and our support team will assist you.

https://hlinstallationvideos.s3.amazonaws.com/2577new-assembly.mp4

WARNING
To ensure proper assembly, please follow all steps and use all parts. Failure to follow this warning can result in serious injury to yourself or others.

Package List

• Without further ado, we kindly suggest you to list all parts needed for the chair first.

Assembly Instruction

Step 1:
Insert Casters (F) into the Chair Base (E). The insert Gas Lift (D) into the hole in the center of the Chair Base (E).

Step 2:
Attach the Seat Mechanism (C) to the bottom of the Chair Seat (A) using Bolts (K) by Allen Wrench (H) as shown.

Note: Tighten the bolts completely

Step 3 :
Attach the pre-assembled Chair Back & Armrest (B) to the Seat Mechanism (C) using Bolts (I) by Allen Wrench (H) as shown.

Note: Tighten the bolts completely

Step 4 :
Position the assembled chair upright with the Seat Mechanism (C) facing down. In-sert the Gas Lift (D) into the center hole of the Seat Mechanism(C) and press down until fully engaged.

Step 5 :
Attach Headrest (G) to Chair Back (B) using Bolts (J) by Allen Wrench (H).
Note: Tighten the screws completely.

CAUTION:
Make sure all bolts and screws are fully tightened before using chair.
Lubricate all moving parts and tighte all bolts/screws every 6 month or whenever needed.

Instructions For Use

Operating the tilt lockout

To let your chair tilt back, pull the control handle out.
To stop your chair from tilting, sit forward, then push the control handle in.

Tilt Tension: Long stem under the seat with knob

To increase tension:
While seated, turn knob forward (Counter clockwise).

To decrease tension:
While seated, turn knob backward (Clockwise ).

Set the tilt tension to control the resistance you feel when leaning back.

HEADREST

Move the headrest up/down to adjust the height. Angle the headrest up/down to the desired position.

Lumbar Support

Reach the lumbar support on the backside of the chair back, move it up/down to the desired position.

Seat Height: Paddle-shaped lever on the right side

To raise:
While taking your weight off chair, lift lever up.

To lower:
While seated, lift lever up.

At the proper height, your feet should rest flat on the floor.

Armrests adjustment

Reach and press the button on the side of armrest to adjust the height of the armrests.
Hold the armrest pads to adjust pad position: (1) move forward and back-ward; (2) move inward and outward; (3) pivot inward and outward.
Hold the armrest pads to flip up/down the armrests.

Safety And Maintenance

• Do not stand on the chair, Do Not use the chair as a stepladder.
• Use this product for seating one person at a time.
• Do not use the chair unless all bolts and screws are firmly secured.
• Avoid contact with sharp objects to prevent puncturing the fabric.
• Every 6 months, check all bolts and screws to ensure they are tight.
• To clean, spot clean only using a damp towel and mild cleaner, first test on a small, unseen area of fabric.
• Chair weight limit not to exceed 275 lbs.

Safety Information

SEATING USAGE:
Normal use for seating is identified as the equivalent of a single shift, forty- (40) hour workweek. To the extent that a seating product is used in a manner exceeding this, the applicable warranty period will be reduced in a pro-rata manner.
Some retailers might have custom models imported directly from the factory and therefore are not supported by our local service team because we don’t have the correct parts, please contact your retailer directly for support. If you have any questions about that we will be happy to assist and identify those items.

RETURN POLICY：
We adopt a 30 days return policy which means that all products purchased on this website may be returned to us within the timeframe. You need to contact us within 30 days after the product(s) came into your possession and the product(s) must be returned to us without any undue delays. Returned products must be returned in the same condition as they were sent and they must be sent in its original packaging.
If the product is not faulty, (i.e. if you changed your mind or if you are unhappy with the product for some other reason), the cost of shipping will all on you. And it is your responsibility that the package arrives safely to us so we recommend that you use a courier service where it is possible to track the shipment.
If the product is faulty when you receive it please contact us and we will help you out (see more information under Manufacturer Warranty).
We reserve the right to give a partial refund in cases when the product(s) is not in an unused condition, is damaged or has missing parts not due to our error.

HOW RETURNS WORK：
Contact us through the contact form on our website and attach the invoice to the message as proof of purchase. And please also write the reason for return.
We will then get back to you as soon as possible with information on where to send the product(s).
As soon as we have received the product(s) and made an inspection we will inform you of our decision.
If a refund is approved we will automatically credit the purchase to your credit card or original method of payment.
If the product(s) is damaged, not in its original condition or missing parts we will inform you if you are eligible for a partial refund. This is decided from case to case depending on the severity of the damages or what parts are missing.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>