PETEMPO SKUJ46022 5L Automatic Cat Feeder User Manual

PETEMPO SKUJ46022 5L Automatic Cat Feeder

Exploring Your Pet Feeder

Specifications

• Capacity Applicable Kibble
• 5L/1.32 Gal 0.118-0.709 inch / 3-18 mm dry food
• Power Supply DC 5V Power Adapter 3 x Alkaline D Battery for backup (Battery is not included in this device’s accessories)

Assembling Your Pet Feeder

1. Press the lock buckle to open the lid. Take out all accessories and remove all packing materials.
2. Plug-in DC cable. Install 3 x D batteries for backup power in case of power outage.
3. Align the notches and then snap the splitter into the middle of the bowl holder.
4. The support bars can be installed through the holes at the bottom of the base so as to raise the height.
5. Place bowls in bowl holders. Lift the feeder and attach the bowls to the notch underneath the base.
6. Take the desiccant bag out from the packaging open the desiccant box and place it in. Put the lid back on. The desiccant bag is recommended to be changed once a month.

LED Display

Control Panel

Using Your Pet Feeder

• Make sure that the pet feeder is properly installed before filling the food tank.

Add Pet Food & Powder on

1. Fill the food tank with dry pet food (0.118-0.709 inch). Cap the lid back and press to snap in place.
2. Plug in the equipped power adapter. The LED display will light up, indicating the feeder is on.

Connect the APP

1. Please ensure that the WiFi is 2.4GHz, this product does not support a 5GHz WiFi network at the moment. Download the app from the lOS or Android APP Store: Tuya/SmartLife. Open the APP and make sure your phone is in a WiFi environment. Register according to the guidelines.
2. Click on “Add Device” and enter the WiFi name and password.
3. After the device is successfully connected, you can start to formulate a feeding plan:
   • Meal Plan: You can add up to 10 feeding schedules and set up to 60 portions at a time.
   • Feed Record: Click to view the feeding history. When the device has no external network, there is no feeding history, but the device will still feed normally.
   • You can also feed manually by the APP.

Care and Cleaning

• Always dry all parts thoroughly before reassembling them for the next use.
• It is recommended to clean the feeder regularly for the health of your pets.

Cleaning Bowls & Holders

1. Lift the feeder and remove the bowl holder. Rinse the bowls off and dry them. Cleaning Lid, Tank & Tank Base
   

2. In the unlocked status, hold for 3s until a beep is heard to unlock the food slider. Before cleaning the feeder, please remove the battery and turn off the power.

3. Press the lock buckle to open the lid. Take out the desiccant bag.

4. Slide the lock latches on both sides to remove the tank and tank base.

5. Rotate the four lock latches to the unlocked position, then take out the food slider.

6. Rinse the lid, tank, tank base, and food slider, then dry them thoroughly. Wipe the base with a soft and damp cloth. Do not rinse or immerse the tank nase in water.

7. Hold the food slider and place it back to the base. Rotate the lock latches to lock the slider in place.

8. Refer to the fourth step and reinstall the feeder in the same way.

Important Safety Instructions

Intended Use

• Children should be supervised to ensure that they do not play with, in, or around the appliance.
• Intended for use with dogs or cats only. Do not use this pet feeder with puppies, kittens, dogs, or cats not able to reach the food tray or with any physical disability.
• Use the appliance only for intended household purposes as described in this User Manual.

Electricity Safety

• DO NOT operate the appliance if it has a damaged power cord or plug, or if it is malfunctioning or has been damaged in any manner
• DO NOT immerse the power cord, plugs, or the device base in water or other liquid or allow moisture to come into contact with these parts.
• To reduce the risk of electrical shock, do not place or store an appliance where it can fall or be pulled into a tub or sink.
• Always unplug the appliance when not in use, before putting on or taking off parts, and before cleaning. Never unplug by pulling on the power cord.
• Use ONLY the provided power adapter and charging cable.

Related To Use

• DO NOT attempt to disassemble, repair, modify, or replace any part of your product. All servicing should be performed by qualified personnel only No user service-able parts inside.
• DO NOT allow pets to chew on or swallow any parts. Cover or hide the power cord with care to prevent pets from biting.
• DO NOT lift the pet feeder by lid, hopper, bowl, or bowl holder. Lift and carry the feeder using both hands and the hopper base, while keeping the unit in an upright position.
• Install or store the pet feeder on a level surface against the wall or in a corner to avoid tripping.
• For dry food use only. Do not use wet, canned, moist food, or pet food with special shapes, holes, or diameters above 18mm/0.709 inches.
• Install 3 alkaline D batteries (not included) for backup power in case of a power outage.
• Before leaving for an extended time, always replace batteries with new batteries. Check operation frequently to be sure the pet feeder is dispensing properly.
• Dispose of all packaging materials properly. Keep away from children and pets.

Troubleshooting

Networking is not successful

1. Please confirm whether it is visitor mode, please register an APP account to use it for the first time.
2. Please make sure the network password is entered correctly.
3. Please make sure the WiFi signal is good, and it is recommended that the distance should not exceed 10 meters to avoid poor network signal.
4. Please make sure to use a 2.4GHz WiFi network, this product does not support a 5GHz WiFi network at this time.

Searching for devices not available
Reset the device. Unlock it and press the manual feeding button for about 5 seconds, and the WiFi indicator will go out. Release the button, the WiFi indicator will flash, indicating the reset was successful.

No grain, stuck grain

1. Please check if the remaining food is sufficient.
2. Please make sure that the grain outlet is not too full, in this case, you can reduce the number of servings of grain.
3. After the grain jam, please clean up the grain bucket to ensure that the phenomenon of grain jamming is lifted before normal use.

Does not work when connected to the power supply

1. Please check if the power plug is properly connected
2. The power indicator will light up automatically when the plug is properly connected.

The feeder shows “offline”

1. Please check whether your cell phone network is connected properly
2. Please check that the distance between the feeder and router is no more than 10 meters and probably no concrete walls between them.
3. If the feeder is disconnected, please don’t worry, the machine will reconnect after a while. Even if the network is disconnected, the chip has a memory storage function, so the feeding plan will go on as usual.

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>