JAMG HE Rapid 3D Printer Resin User Manual

Technical Data Sheet 2023
Hi-Speed Standard Resin
Standard Pro Resin
10K Standard Plus Resin
10K Washable Resin
10K Nano Resin
M5 Series Resin
Plant Based Standard Resin
Plant Based ABS Like Resin

Shenzhen Yongchanghe Technology CO., LTD.
RM 1001, Huaide International Building, Fuyong Bao’an District, Shenzhen, China 518103
Website: www.jamghe.com
Tel: +86 -755 – 2788 9946

Printing Setting

Model No.| Layer
height
(mm)| Bottom
exposure
time(s)| Layer
exposure
time(s)| Bottom
Lift
(mm) Distance| Lifting
Distance
(mm)| Bottom
Lift
Speed
(mm/min)| Lifting
Speed
(mm/min)| Retract
Speed
(mm/min)| Rest time
after
retract
---|---|---|---|---|---|---|---|---|---
10K Nano Resin| | | | | | | | |
MS Series Resin| | | | | | | | |
| | | 2.5–3.5| | | | | |
10K Standard Plus Resin| | | | | | | | |
| | | orange| | | | | |
10K Washable Resin| | 25-35| red resin :| | | | | |
| | | 3–4| | | | | |
Plant Based Standard| | | | 6| 6| 60| 80| 150| 2–3
Resin| 0.05| | | | | | | |
Plant Based ABS Like
Resin| | | 2.5–4.5| | | | | |
Standard Pro Resin| | | 2.5–4.5| | | | | |
Hi-Speed Standard Resin
(Normal 3D Printer)| | 20-25| 1-1.5| | | | | |
Hi-Speed Standard Resin
(Hi-Speed 3D Printer)| | 20-25| 1.2–1.8| 3| 3| 1300| 1300| 1300| 0.5
Hi-Speed Standard Resin
(Hi-Speed 3D Printer,| 0.1| 20-25| 1.8-2| 3| 3| 1300| 1300| 1300| 0.5
ACF film)| | | | | | | | |

Above settings are tested on ELEGOO MARS 3 (6.6” monochrome LCD screen,light intensity 3500~4500µw/㎝²), they should be adjusted according to different 3d printers and printing model structure，most settings can be keep as the printers’ default firstly.
Hi-Speed Standard Resin tested on high speed printer Anycubic M5S (10.1inch, 12K，ACF film)

1. Bottom layer count = Bottom layer thickness/ Layer height+1，e.g. Bottom height 0.4mm, layer height 50um, the bottom layer count= 0.4mm/0.05mm+1=9 layers.
2. The exposure time should be adjusted according to printer light energy, layer thickness and model structure. If the layer height less than 0.05mm, we suggest the exposure time of each layer will be deducted about 0.5s.
3. If light power of printer is getting weak and cause failure, don’t forget to add exposure time.
4. When printing with ordinary FEP/NFEP film, the recommended lifting distance as below: Less than 7” screen size, lifting distance: 6mm；
   7-10”screen size, lifting distance: 8-10mm
   10.1”screen size, lifting distance: 11mm；
   13.3”screen size, lifting distance: 14mm
   15”screen size, lifting distance: 15mm
   While printing with fast printing film (ACF film), lifting distance can be decrease 30-50%. e.g. lifting speed was 80 (mm/min) at regular film, you can adjust to 40-60(mm/min) when using fast printing film (ACF film).
   Notice：shake the resin well before use.

Technical Specification

Hi-Speed Standard Resin & Standard Pro Resin & 10K Standard Plus Resin & 10K Washable Resin

| Hi-Speed
Standard Resin
FR-A| Standard Pro
Resin| 10K
Standard
Plus Resin| 10K Washable
Resin| Test
Standard
---|---|---|---|---|---
Tensile strength (MPa):| 42.77+10%| 42.77+10%| 37.88 ±10%| 31.44 ±10%| ASTM D638
Tensile modulus (MPa):| 518.35+10%| 518.35+10%| 615.49 ±10%| 471.03 ±10%| ASTM D638
Elongation at yield point(%)| 5.38+10%| 6.38+10%| 3.09 ±10%| 6.32 ±10%| ASTM D638
Flexural modulus (MPa):| 1284.19+10%| 1284.19+10%| 1699.7 ±10%| 1091.45 ±10%| ASTM D790
Flexural strength (MPa):| 47.48+10%| 47.48+10%| 57.91 ±10%| 40.82 ±10%| ASTM D790
Notched impact strength
(1/m):| 101.04+10%| 101.04+10%| 72 ±10%| 50 ±10%| ASTM D256
Maximum pulling force (N):| 1779.51+10%| 1779.51±10%| 1575.93±10%| 1308.20±10%| ASTM D638
Maximum force point of
deformation (mm)| 7.61+10%| 7.61+10%| 3.62 ±10%| 4.33 ±10%| ASTM D638
Elongation at break (%);| 9.26+10%| 15.26+10%| 6.41 ±10%| 7.65 ±10%| ASTM D638
Hardness (Shore D):| 80-86D| 80-86D| 80-88 D| 80-85 D| ASTM D2240
Viscosity (MPa.S):| 50-100| 200-400| 250-400| 70-175| GB/T 4472
Density (g/cm3):| 1.05-1.25| 1.05-1.25| 1.05-1.25| 1.05-1.25| GB/T 22235

10K Nano Resin & M5 Series Resin & Plant Based Standard Resin & Plant Based ABS Like Resin

| 10K Nano
Resin| MS Series
Resin| Plant Based
Standard Resin| Plant-Base
ABS-like Resin| Test Standard
---|---|---|---|---|---
Tensile strength (MPa):| 37.9 ±10%| 45.40+10%| 32.43 ±10%| 27.46 ±10%| ASTM D638
Tensile modulus (MPa) :| 508.12 ±10%| 687.73+10%| 424.97 ±10%| 328.5 ±10%| ASTM D638
Elongation at yield point(%)| 6.21 ±10%| 6.09+10%| 5.54 ±10%| 5.57 ±10%| ASTM D638
Flexural modulus (MPa):| 1188.91 ±10%| 1570.52+10%| 768.67 ±10%| 531.27 ±10%| ASTM D790
Flexural strength (MPa):| 41.4 ±10%| 49.80+10%| 29.82 ±10%| 20.27 ±10%| ASTM D790
Notched impact strength (Jim):| 46 ±10%| 42+10%| 40.03 ±10%| 58 ±10%| ASTM D256
Maximum pulling force (N):| 1576.91 ±10%| 1888.76+10%| 1349.40±10%| 1142.47 ±10%| ASTM D638
Maximum force point of deformation (mm)| 6.87 ±10%| 4.33+10%| 9.86 ±10%| 12.33 ±10%| ASTM D638
Elongation at break (%):| 12.15 ±10%| 7.67+10%| 17.48 ±10%| 21.8 ±10%| ASTM D638
Hardness (Shore D):| 82-86 D| 84-88D| 80-88 D| 78-86 D| ASTM D2240
Viscosity (MPa.S):| 150-300| 200-400| 200-450| 200-400| GB/T 4472
Density (g/cm3):| 1.05-1.25| 1.05-1.25| 1.05-1.25| 1.05-1.25| GB/T 22235

Introduction of Testing Machine & Testing Environment

Computer-controlled Servo Tensile Testing Machine

Digital IZOD Impact Tester

Testing Environment

Temperature: 23±2℃
Relative Humidity: 50%RH±5%RH
Standard For Testing Splines: ASTM
Post Curing Box: 405nm UV, 200mw/cm²
Put the test strip in water and post cured for 1 minute on both sides.

Cleaning and Post-curing

Notice: For water washable resin, just cleaning with water by ultrasonic machine, don’t forget to dry them in and out after post curing.
Caution

1. Wash hand and face thoroughly after handing.

2. Wear protective gloves / mask/protective clothing when using resin.

3. Contact eyes may cause irritation, immediately flush eyes with plenty of water for at least 15 minutes.
   Seek medical advice immediately if necessary.

4. Waste water/waste shall be disposed of in accordance with local environmental regulations.

Storage

1. Please seal the product and store it in a dry, well-ventilated room with no corrosive gas.
2. Stored at 25~30℃ environment.
3. Keep away from heat source, keep away from moisture and avoid sun exposure.
4. Shelf life 24 months.

References

• JAMG HE Committed to 3D Printing Materials – JamgHe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>