SPANARCI 2000 Sandy Portable Air Compressor User Manual
- June 15, 2024
- SPANARCI
Table of Contents
- PRODUCT OVERVIEW
- PACKAGE CONTENTS
- BATTERY LEVEL INDICATOR & CHARGING
- TURNING THE INFLATOR ON/OFF
- CONNECTING THE AIR TUBE AND NOZZLE
- DETECTING THE CURRENT PRESSURE
- DETERMINING THE RIGHT PRESSURE VALUE
- PRESET PRESSURE VALUE
- LIGHT
- INFLATING
- DISCONNECTING THE AIR TUBE
- POWER BANK FUNCTION
- TROUBLESHOOTING
- SPECIFICATIONS
- SAFETY INSTRUCTIONS
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SANDY 2000
AIR INFLATOR
User Manual
Read this manual carefully and keep it for future reference.
Thank you for choosing Spanarci.
Thank you for purchasing the Spanarci Sandy 2000 air inflator. With a large
LED screen and easy-to-use interface, this excellent air inflator has a wide
range of applications.
PRODUCT OVERVIEW
1. Battery indicator | 7. “+” button |
---|---|
2. Pressure unit | 8. “-” button |
3. Pressure value | 9. Light button |
4. Preset mode | 10. USB-A port |
5. Power button | 11. USB-C port |
6. Settings button | 12. Air outlet |
PACKAGE CONTENTS
BATTERY LEVEL INDICATOR & CHARGING
Battery Level Indicator
The battery level is shown by four bars, with each bar representing 25%.
1 bar = under 25%
2 bars = between 25% and 50%
3 bars = between 50% and 75%
4 bars = between 75% and 100%
Note: The battery indicator will flash when the battery level is below
20%.
Charging
Fully charge the inflator before using it for the first time. Please use the
equipped certified PD20W charger and charging cable to charge the tire
inflator.
While charging:
1 bar flashing = under 25%
1 bar solid, 2nd bar flashing = between 25% and 50%
2 bars solid, 3rd bar flashing = between 50% and 75%
3 bars solid, 4th bar flashing = 75% and 100% All 4 bars solid = fully charged
Note:
- The inflator can not be used while charging.
- Make sure to use a certified charger.
TURNING THE INFLATOR ON/OFF
ON
Long-press for 1.5 seconds to turn on.
OFF
When the inflator is turned on, long press 1.5 seconds to turn off.
The inflator will automatically turn off in the cases below:
- After 1.5 minutes of inactivity.
- When the charging cable is disconnected during charging.
- When the inflator is being used as a power bank, after disconnecting the other device.
- Inflate over 2 minutes when the target pressure value is below 5psi.
- Inflate over 2 minutes when the target pressure value is above or equates 120psi.
CONNECTING THE AIR TUBE AND NOZZLE
Schrader Valve
Tires on cars, motorcycles, e-bikes, and most mountain bikes use a Schrader
valve.
To inflate: The inflator can be directly connected to a Schrader valve to
start inflating.
To deflate: Use an proper tool (such as 4mm Allen wrench) to press the pin
inside the air valve to release air.
Presta Valve Adapter
Road bicycles and certain mountain bikes use a
Presta valve which requires the included
Presta valve adapter to be used.
To inflate:
- Connect the Presta valve adapter to the Schrader valve of the air tube.
- Unscrew the ring of the Presta valve of the tire.
- Connect the Presta valve adapter to the tire’s Presta valve to start inflating.
- To deflate: Unscrew the ring of the tire’s Presta valve, and press the valve stem down to release air.
Needle Valve Adapter
To inflate balls like basketballs and footballs, the included needle valve
adapter will need to be used.
To inflate: Screw the needle valve adapter onto the Schrader valve adapter,
then insert the needle into the valve of the ball to start inflating.
To deflate: Insert the needle valve adapter into the valve of the ball, and
gently apply pressure to the ball to release air.
DETECTING THE CURRENT PRESSURE
When the inflator is turned on, connect the air tube to the device to be inflated, then the LED screen will display the current pressure value.
DETERMINING THE RIGHT PRESSURE VALUE
To avoid injuries from bursting items due to over-inflation, make sure you are aware of the maximum inflation pressure before you start.
Tires
The recommended air pressure of tires for cars, bicycles, and motorcycles is
indicated on the tire’s sidewall. The recommended tire pressure for cars is
also indicated on the inside of the driver’s side door.
For details concerning load carrying capacity and recommended air pressures,
refer to your vehicle’s instructions or manual.
Balls
The recommended air pressure for footballs, basketballs, volleyballs, and
other balls is indicated near the ball’s air valve.
Air Pressure Reference Table
Category| Type| Recommended
Pressure Range| Category| Type| Recommended
Pressure Range
---|---|---|---|---|---
Bicycles| Electric Folding Bike tires
12-, 14-, & 16-inch bicycle tires
20-, 22-, & 24-inch bicycle tires
26-, 27.5-, & 29-inch mountain bike tires
Electric Scooter tires
700c road bike clincher tires
700c road bike tubular tires| 10 – 50psi 30 – 50psi 40 – 50psi 45 – 65psi 40 –
50psi 100 – 130psi 120 – 145psi| Motorcycles| Scooter & street motorcycle
tires| 1.8 – 3.0bar
Cars| Car tires| 2.2 – 2.8bar
Balls| Basketball
Soccer ball
Volleyball
Football| 7 – 9psi 8 – 16psi 4 – 5psi 12 – 14psi
Note: Pressure range values are for reference only. Always refer to the instructions or manual of the item being inflated for actual inflation pressure specifications. (The data above is from the QiCYCLE lab.)
PRESET PRESSURE VALUE
Note
- Press the once to choose the usage scenario from
- Press the for a few seconds until the icon of the unit blinks, press once to choose the units you want from KP PSI and Bar.
- Wait for 5 seconds until the unit icon stops bilking then press the to set the pressure value.
- Press the to pump anything you want.
Switch Modes
Click the to switch between the four inflation modes below.
| Car Mode: Default 2.5bar
Adjustable Range: 1.8-3.5bar
---|---
| Bicycle Mode: Default 45psi
Adjustable Range: 30-145psi
| Motorcycle Mode: Default 2.4bar
Adjustable Range: 1.8-3.0bar
| Ball Mode: Default 8psi
Adjustable Range: 4-16psi
Note:
When you have finished inflating an item, the manual mode will remember the
target pressure value as its default pressure value.
For the best results, we suggest you inflate items like balls via the ball
mode.
Adjusting the Preset Pressure
After selecting a mode, press or to increase or decrease the target pressure
value. Press and hold the or button to quickly adjust the pressure value.
Press the and at the same time to display the real-time battery voltage
LIGHT
Press the 1.5 seconds to turn the inflator’s light on/off. The bright light
makes it easier to operate in the dark, especially while connecting the air
compressor to a valve.
When the light is on, press the to cycle through Spotlight, SOS and OFF.
INFLATING
Start Inflating
Press the to start inflating. When inflating, the air compressor may be as
loud as 75 – 80 dB. Please take appropriate precautions to protect your
hearing. The air compressor and air tube can get very hot after running for a
while.
To avoid skin burns, avoid prolonged exposure to the air tube with bare skin.
Stop Inflating
Once the target pressure value has been reached, the inflator will
automatically stop inflating. The inflator can also be manually stopped at any
time by pressing the while inflating.
Caution
Items such as balloons, beach balls, and swim rings cannot be automatically
inflated because they have an air pressure requirement below the air
compressor’s minimum pressure range.
Only inflate these items manually with caution.
Battery Information
The inflator’s battery lasts about 40 minutes on a full charge, running
without a load at an ambient temperature of 25°C. Using the air compressor
under a heavy load or at lower ambient temperatures may reduce its battery
life.
DISCONNECTING THE AIR TUBE
The air compressor’s air hose may get very hot after inflating. To prevent injuries, exercise caution when disconnecting it from a valve. Some air may leak out of the valve when disconnecting the air compressor. To avoid pressure loss, quickly disconnect the air hose from the valve.
POWER BANK FUNCTION
This inflator can be used as a PD20W&5V/3A power bank when it is not being
charged or inflating other devices.
The battery needs to have a reasonable level of charge in order to work as a
power bank.
Note:
In energy saving mode, when disconnecting the charged device from the
inflator, it will automatically turn off.
TROUBLESHOOTING
Problem | Solution |
---|---|
Three kinds of error display | :Air pressure changes less than 2psi in two |
minutes. Please check the connection carefully to make
sure that there is no air leaking.
:The power of the product is too low, please fully charge it before using it.
:temperature protection function.
when the cylinder temperature reaches about 120 ℃, it will display E02 and
turn off the motor.
Problem| Solution
---|---
Slow inflation speed| 1. Check whether the air compressor’s battery level is
sufficient.
2. Check whether the air hose is leaking.
3. Check whether both ends of the air hose are securely connected.
4. Check whether the item that is being inflated is leaking
Air compressor turns on but does not inflate| 1. Check whether the air
compressor’s battery level is sufficient.
2. Check whether the pressure of the item being inflated exceeds the preset
pressure.
Unable to increase or decrease the preset pressure| Make sure the air
compressor is set to the correct mode.
Manual mode has a blank display without any icons and allows you to adjust the
preset value within the range of 3 – 150 psi.
The inflator inflates normally but the displayed pressure is zero| The
pressure of low-pressure inflatables including balloons is too low to be
measured.
Problem| Solution
---|---
Air leakage after connecting the air tube| Make sure the air hose is securely
connected.
Comparing with the standby state, the battery level indicator is different
while inflating.| The voltage level of lithium battery will significantly drop
while discharging power, which causes the battery level indicator showing
different displays when inflating comparing with the standby state.
The battery level indicator doesn’t
show on the screen after charging| Use a certified adapter and the included
charging cable, and try charging again.
The inflator can not charge other devices.| 1.Make sure the remaining battery
level is sufficient.
2.The inflator can not charge other devices while inflating.
SPECIFICATIONS
Name | Air Inflator |
---|---|
Model | Sandy 2000 |
Dimensions | 331×97×91mm(Excluding air tube) |
Inflation Pressure Range | 3-150psi / 0.2-10.3bar |
Operating Temperature | Charging :0℃~45℃,Discharging :-10℃~45℃ |
Storage Temperature | -10℃~45℃ |
Air Valve Dimensions | Length 400mm |
Battery Capacity | 6000 mAh(22.22 Wh) |
Working Noise | Lower than 80dB within 1 meter |
Input | PD20w |
Output | PD20W & 5V/3A |
Input Port | USB Type-C |
Output Port | USB-A & USB Type-C |
Charging Time | <2hours |
Sensor Accuracy | ±2psi |
SAFETY INSTRUCTIONS
- This product is not a toy and should not be used by children. Users should be above 16 years old.
- Keep a safe distance between children and the inflator while inflating. There is a built-in lithium battery inside the product. Don’t place the product in fire or dump the battery.
- Overheating, damage, or water may increase the risk of fire or explosion. It’s best to keep the product away from heat sources, and not leave it for prolonged periods in a hot car. If the inflator becomes very hot, there is a chance it could explode.
- Please store the product in temperature ranging from -10ºC~45ºC. Extremely hot or cold environments may damage the battery and shorten the lifetime of the inflator.
- Long-time storage of the product may decrease the effectiveness of the battery. Charge the inflator at least once every three months to maintain its performance.
- The product has a built-in DC motor which may generate sparks during operation. Do not use it in an environment with dust or gas that is liable to explode.
- If there is an unusual noise or the temperature becomes very high during inflating, please turn off the inflator immediately
- Before setting the inflation pressure value, make sure the pressure unit is correctly selected. Mixing up psi and bar could lead to dangerous overinflation.
- Unit conversion: 1bar = 14.5psi, 1bar = 100kPa Do not leave the inflator unattended while it is in operation.
- Please use the product in a dry and clean environment.
- The intrusion of sand and dust may cause damage to the product. Don’t wash the product with water.
- Please use a certified adapter and the included charging cable to charge this product. Malfunction caused by actions not in accordance with the above requirements is not covered by the warranty.
- After running for a long time, the temperature of the junction between theair tube and the main body can become very high.
- To avoid burns, avoid touching it.
- This inflator is equipped with short circuit protection. Do not connect its USB-A port with its USB-C port.
Caution: To reduce the risk of electric shock, do not expose to rain. Store indoor.
Ningbo Morepin Electrical Technology Co.,Ltd.
E-mail: automotive@spanarci.net
ADD: No.25,Xingye Road,Yangming Industrial Park,
Yanging Street,Yuyao,Zhejiang
MADE IN CHINA