Chaoshuo CS-9 Folding Drone with Obstacle Avoidance User Manual

Chaoshuo CS-9 Folding Drone with Obstacle Avoidance

Product Information

Specifications

• Obstacle Avoidance Head
• Speed: 60
• One key reset
• Obstacle avoidance
• Headless Mode
• Left joystick
• Right joystick
• Fine-tuning key
• Mobile phone holder

Product Usage Instructions

Mobile Phone Installation

1. Open the mobile phone bracket on the remote control.
2. Install the mobile phone on the mobile phone bracket.

Aircraft Calibration:
If the aircraft cannot rise vertically after taking off, it can be corrected by pulling the left and right joysticks into an outer eight at the same time with a sound of Di and the indicator light flash quickly to long- term on, the calibration is completed. When executing the correction command, the aircraft must be placed in a smooth state parallel to the horizontal line, otherwise, the correction effect will be affected.

Lighting:
The remote control is produced with light. When the power switch is on, the two sides of the remote control will emit a blue light, and when the power switch is off, the two sides of the light will be off.

Flip Forward/Flip Backward:
To perform a flip forward or backward maneuver, refer to the specific instructions provided in the user manual.

Frequently Asked Questions (FAQ)

What should I do if the aircraft is not rising vertically after takeoff?
If the aircraft is not rising vertically after takeoff, you can perform the calibration by pulling the left and right joysticks into an outer eight simultaneously. Ensure that the aircraft is placed in a smooth state parallel to the horizontal line during calibration.

How do I install my mobile phone on the remote control?
To install your mobile phone on the remote control, open the mobile phone bracket and securely place your mobile phone on it.

What does the lighting on the remote control indicate?
The lighting on the remote control indicates the power status. When the power switch is on, the two sides of the remote control emit blue light. When the power switch is off, the lighting will be off.

FCC Warning:
This device complies with part 15 of the FCC Rules. Operation is  subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in a portable exposure condition without restriction.

Please read this manual carefully before operation and keep it properly for future reference.

KNOW YOUR DRONE
With 2.4G frequency band for long remote control distance, Drone allows multiple flights at the same time without any interference. User can control it to fly, hover and take photos/ videos with APP and WIFI connection on smart phone.

1. Upper Casing
2. Lower Casing
3. Propeller
4. Arm
5. Battery
6. Motor
7. Camera
8. Obstacle Avoidance Head

ACCESSORIES

Notes:
Please check the number of accessories carefully las shown above). Please provide proof of purchase and contact the store for replacement if any missing parts.

OPTIONAL ACCESSORIES LIST

Notes:
If any of the above accessories are damaged during operation, you can contact the seller to purchase them.

PRE-FLIGHT PREPARATION

1. FLIGHT ENVIRONMENT
   Indoor: Spacious spaces away from barriers, crowds, or pets are preferred
   Outdoor : Sunny, windless, and breezy weather are preferred.
   Please keep the drone in sight during the flight and keep it away from barriers, high-tension cables, trees, and people.
   Do not fly in extreme environments, such as hotness, coldness, strong wind, or heavy rain.

2. OPEN THE WINGS
   OPENING STEPS

3. Open the front arm(close to the camera)

4. Open the back arm. Fold the back arm first and then the right arm when folding.

5. ASSEMBLING PROTECTIVE GUARD
   Align the protective frame with the arm and install it (Figure 1), press it until it is in place, and then press the position (Figure 2) up to fasten the protective frame.

6. ASSEMBLING PROPELLERS
   Align the blades with the motor shaft and install them the arm identification must be consistent with the blade identification), Tighten the screw clockwise

7. BATTERY CHARGING FOR DRONE
   A : Remove the lithium battery from the bottom of the drone.
   B : Connect the USB charging cable with the charging interface of the lithium battery.

Notes:
LED lights are on when charging and the red light turns off when full charging completes. The charging time is about 150 minutes.

BATTERY INSTRUCTIONS EUEMIE

• There is a certain risk when using lithium battery. It may cause fire, body injury or property loss. Users must be aware of the risks and take full responsibility of using battery improperly.
• If battery leakage occurs, please avoid contacting your eyes or skin with electrolyte. Once it happens, please wash your eyes with clean water and seek medical care immediately.
• Please remove the plug immediately if you sense any peculiar smell, noise or smog.

Battery Charging

• Please use the charger from original factory to ensure your safe usage. 34880
• Do not charge dilatant or outworn battery.
• Do not over charge battery. Please unplug the charger once fully charged.
• Do not charge the battery next to inflammables, such as carpet, timber floor or wood furniture or on the surface of electro- conductive objects. Please always keep an eye on the battery when charging
• Do not charge battery which not cool down yet.
• The charging temperature should be between 0°Cto 40°C.

Battery Recycling

• Do not dispose of the battery as daily rubbish. Please familiarize yourself with the local garbage disposal method and dispose it according to the special requirement.

KNOW YOUR REMOTE CONTROL

Parts of remote control

1. Speed
2. One-key Flips & Rolls 360° BA
3. Obstacle avoidance
4. Headless Mode
5. Left joystick
6. Right joystick
7. One-key Ascend
8. One key reset
9. One-key Landing
10. Fine-tuning key
11. Power switch
12. Mobile phone holder

MOBILE PHONE INSTALLATION

1. Open the mobile phone bracket on the remote control.
2. Install the mobile phone on the mobile phone bracket.

LITHIUM BATTERY INSTRUCTION

1. Open the remote control battery cover
2. Remote control battery installation

AАА batteries
Open the battery cover and insert the 3 AAA batteries correctly according to the electrode instructions.(Batteries not included)

Notes

1. Make sure the battery are loaded correctly according to the polarity indications on the battery compartment.
2. Please do not mix old and new batteries together.
3. Please do not mix different tynes of batteries todether

SIGNAL CONNECTION OF TRANSMITTER AND RECEIVER

1. Turn on the drone and place it on a level surface, the indicator light of transmitter and the LED of drone flashing.
2. Push the throttle joystick to the highest point then push back to the lowest point, and whenyou hear two beeps, the indicator light of transmitter and the LED of drone become normally on, the signal connection as completed.

TRANSMITTER CALIBRATION
If the aircraft cannot rise vertically after taking off, it can be corrected by pulling the left and right joysticks into an outer eight at the same time with a sound of the indicator light flash quickly to long-term on, the calibration is compl eted. When executing the correction command, the aircraft must be placed in a smooth state parallel to the horizontal line, otherwise, the correction effect will be affected.

START YOUR FLIGHT

One-key Ascend
Press the “One-key Ascend” button, and the drone blades rotate and automatically fly to a height of 1.5 meters.

Basic Flight
Use the left joystick to control the flight altitude and turn left/ right, and the right joystick to control the forward, backward, left, and right side flight directions.

• Left joystick
• Right joystick

Lighting
The remote control is produced with light. When the power switch is on, the two sides of the remote control will emit blue light, and when the power switch is off, the two sides of the light will be off

Flips & Rolls
When the drone reaches more than 3 meters high, click “360° flips and rolls” and move the right joystick to a certain direction. the drone will rotate in that direction.

Right joystick

Headless Mode
The flight direction of drone is subjected to the direction of remote control.

1. When drone adjust the frequency, the drone is default as common mode. Then the indication light of drone is normally on. When you press the headless function key of remote control, the remote control beeps once and enters headless state. When you press the headless function key again, you listen to a long beep sound and the drone exits the headless mode.
2. In the headless state, operator doesn’t need to identify the direction of nose, but control the drone according to the operating lever of remote control.

Hover
When you release the left joystick (throttle) after the ascent/descent action, the dronewill hover at a certain height

Left joystick

Obstacle Avoidance Mode

Press the button to turn on the obstacle avoidance mode, and press again to turn off the obstacle avoidance mode. Avoid obstacles on three sides and retreat in the opposite direction of the obstacle.

It is recommended to turn on the obstacle avoidance function in an indoor flight environment with a length and width of 6 × 6 meters or more. When the UAV turns on the obstacle avoidance mode, the speed will slow down and the fast gear cannot be turned on. Therefore, it is recommended to fly indoors when the obstacle avoidance mode is turned on.

FINE-TUNING FUNCTION

When the aircraft spins in the air or tilts in different directions, you can use tine-tuning to correct the action. Press the fine-tuning button and hear a beep, then move the joystick in the opposite direction to adjust and calibrate until the aircraft does not deviate. If there is no operation for 5-6 seconds after entering the fine-tuning, the fine-tuning function will automatically exit. Forward/Backward

1. 1. Fine-tuning

2. Left/Right Side
3. Fly Fine-tuning

Notes

When the drone is within 30cm from the ground, it will be affected by the blade vortex made by itself and become unstable. This is “ground effect”. The lower the drone is, the greater the effect will be.

FAQ

FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>