Govee H5040 Wi-Fi Water Sensor Alarm User Manual

: June 15, 2024
: Govee

Table of Contents

Govee H5040 Wi-Fi Water Sensor Alarm
Packing List
Installing Your Device
Troubleshooting
Warning
Specifications
FCC and ISED Canada Statement
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Govee H5040 Wi-Fi Water Sensor Alarm

Govee-H5040-Wi-Fi-Water-Sensor-Alarm-product-image

Model:H5040+H5054
Water Detector With Wi-Fi Gateway

Detectors have paired with the gateway in advance. You only need to connect the gateway to the network. Please see pages 01-09.

At a Glance

Govee-H5040-Wi-Fi-Water-Sensor-Alarm-1

Govee Water Leak Detector is a device that sounds an alarm once detecting water drip or leak. Connecting to Wi-Fi via the gateway, it instantly sends you alert notifications of water leaking by app or email whether you are at home or outside.

433 is a communication protocol with a frequency of 433MHz.
Wi-Fi Gateway
- Wi-Fi Pairing Button : Connect the gateway to Wi-Fi.
- 433 Pairing Button: Connect the gateway to the water leak detector.
- LED Indicator: Show status of the gateway.

Govee-H5040-Wi-Fi-Water-Sensor-Alarm-2

Water Leak Detector

Sensor Contact: Detect water drip. Sensor Probe: Detect water leak.
Push Button: Pause alarm/ Adjust volume. Batteries: 2 X AAA Battery.

Packing List

Packing List|
---|---
SKU

Water Leak Detector

| B5040101| B5040105| B5040109
Wi-Fi Gateway| | |

AAA Battery
User Manual

| 6| | 4
Service Card| | |

Checking the Water Leak Detector

Insulation sheet removal.
Pull out the insulation sheet vertically.
Press the button and the detector beeps 1 s later, indicating it works well. If not, please open the back cover via a PH00/PH0 screwdriver to replace new batteries.
Adjust alarm volume by pressing the button twice within 1 sand the indicator will flash quickly. The volume level (]$ cycles through HIGH – MEDIUM – LOW- MUTE, and default volume is high.
The detector will alarm if you drip some water on the sensor contact or put it on the surface with water.
Press the Push Button to stop alarm for Ss. Remove the device from water and wipe it up to stop alarm completely. Notice: When the battery is low, the device sounds “dididi” and flash red slowly.

Installing Your Device

Plug the gateway into a power outlet;
Lay the water leak detector flat.
Notice : Keep distance between the gateway and the detector less than 60m/197ft.

Preparation Before Connecting

A Wi-Fi router supporting the 2.4GHz (NOT 5GHz) and 802.11 b/g/n bands.
(Notice: Most of 5GHz routers can also be set to 2.4GHz band or dual band.)
Make sure Wi-Fi name and password are correct.
A smartphone or tablet supporting 2.4GHz network.
Download the app named Govee Home from the App Store (iOS devices) or Google Play (Android devices).

Connecting to a Wi-Fi Network

Connect your phone to 2.4GHz network;
Notice: Android device users should turn on Location and iOS users should tap Setting – Govee Home – Location -Always in your phone.
Open Govee Home, tap “+” icon in the top right corner and select “H5040”;
Press and hold Wi-Fi Pairing Button” 111 “for 3s.The gateway will get ready to connect to Wi-Fi when the indicator flashes blue slowly;
Follow on-screen instructions in the app to complete the connection;
Connected to Wi-Fi successfully. The indicator keeps solid blue and you can find the water leak detector in the device list;
Notice: If you cannot find the detector, please swipe down the device list page to refresh or refer to “Add or Re-add Water Leak Detector” below to add the detector.
The indicator keeps solid red if it failed to connect toWi-Fi;

Please check the above steps and try again; or you can select “H5040” in the app and tap “Video Guide” for more instructions.

Notification Setting

App notification: Open app, select “water leak detector” in the device list, and tap setting icon in the top right corner.

Add or Re-add Water Leak Detector
Notice: The detector is added by default when the gateway connects to Wi- Fi successfully.

Press the 433 Pairing Button” <!> “and hold for 3s. The gateway will get ready to pair when the indicator flashes red and blue alternately;
8 Put the detector nearby the gateway. Press the Push Button and the detector will send pairing signal;
The gateway is receiving the signal;
The gateway has paired with the water leak detector
Swipe down the device list page in app to refresh and you can find the new-added device;
Notice:
- If the gateway fails to pair to the detector in 30s, its indicator will flash blue quickly and it will exit the pairing mode.
- There’s 1 s delay for beep sound after you press the Push Button.
- Please check the above steps and try again if pairing fails.

Troubleshooting

The gateway cannot connect to Wi-Fi. /The connection is unstable.
5GHz network is not supported. The device ont;supports 2.4GHz.
Check the name of the network and password.
Place the gateway within coverage of the router signal.
No/Delayed notification in the app.
Make sure that Android device users turn on Location and iOS users select “Setting – Govee Home – Location -Always” in the phone.
Keep the distance between the gateway and the detector as close as possible.
No obstructions between the gateway and the detector is suggested.
The time interval between two water detection should be longer than 90s, otherwise the app won’t push notification.
Check whether the indicator of the gateway flashes when the detector is triggered. If not, please re-add the detector.

Warning

Keep devices work temperature within 32°F – 140°F and humidity below 90%RH.
Do not disassemble devices violently.

Specifications

Wi-Fi Gateway

Voltage| AC 110-240V 50/60Hz
Wi-Fi Frequency| 2.4GHz
Wi-Fi-enabled Distance| 100m/328ft
Water Leak Detector

Customer Service
Warranty: 12-Month Limited Warranty
Support: Lifetime Technical Support
Email: support@govee.com
Official Website: www.govee.com

CAUTION:
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

FCC and ISED Canada Statement

This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES -003. Cet appareil numE!rique de la classe Best conformed a la norm NMB-003 du Canada.

FCC and IC Radiation Exposure Statement

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Responsible party