Govee H6171 Phantasy Pro Outdoor RGBIC LED Strip Lights User Manual

Govee H6171 Phantasy Pro Outdoor RGBIC LED Strip Lights

Safety Instructions

Read and follow all the safety instructions:

• The strip lights and the control box have an IP65 water-resistant rating and can be used outdoors. Keep the adapter and the socket away from water during installation and usage.
• To prevent the strip lights from falling down, ensure they are installed with both the adhesive tape and the clip.
• Be cautious of static electricity during installation and usage. Keep the product away from sharp objects or strong corrosive chemicals.
• When bending the strip lights during installation, avoid folding the LED components as it may affect the product’s life span.
• Remove nails, metal, or other conductive objects from the installation surface before attaching the strip lights, as it may cause short-circuiting.
• Do not install the strip lights near any heat sources.
• Do not allow children to install the strip lights alone.
• Avoid installing the strip lights near potentially dangerous sources (e.g., candles, liquid-filled objects).

Introduction

Thanks for choosing the Govee Phantasy Pro outdoor RGBIC strip lights segmented control function for outdoor use. It can be controlled via the Govee Home app and the 433-remote controller. With an IP65 water-resistant rating, the strip lights can safely bring you a colorful lighting experience.

What You Get

At a Glance

Using Your “Remote Controller”

through 32 colors.
Color Select (RGBW)| Press to change the color.
R: Red, G: Green, B: Blue, W: White
Sleep| Change the light to warm white with 1% brightness.
RGBIC| Press to cycle through 7 preset RGBIC lighting effects.
Auto| Press to randomly switch between 10 Scene Modes.
Music Mode| Energetic, Rhythm, Rolling, Spectrum (from left to right).

Installing Your Device

Before You Install

1. Unpack the box and check all items listed in the packing list.
2. Power on the strip lights and check whether it lights up.

Installing Steps

1. Drill a hole in the wall for clip installation. Ensure the  plastic anchor can fit in the hole firmly.
2. Align the clip with the plastic anchor and attach it to the wall. Insert the screw into the hole and firmly secure it in the plastic anchor.
3. Wipe the surface of the wall to ensure it is dry and clean. Tear off the film on the 3M adhesive tape and stick the strip lights onto the installing location. Press down on the strip lights repeatable to ensure it is firmly attached.
4. Remove the protective film on the control box to stick it to the chosen location.
5. Power on the strip lights and begin using!

Pairing Your Device with the Govee Home App

What You Need:
A smartphone or tablet running iOS 8.0 (or above) or Android 4.3 (or above).

1. Download the Govee Home app from the App Store (iOS  devices) or Google Play (Android devices).
2. Turn on Bluetooth on your smartphone.
3. Open the app, tap the”+” icon in the top right corner and search for “H6171”.
4. Tap the device icon and follow the onscreen instructions to complete pairing.

Specifications

Troubleshooting

1. The adhesive tape is not strong enough.
   Use the clips to secure the strip lights firmly during installation.

2. Cannot connect to Bluetooth.

   • Do not skip Bluetooth connection in the app.
   • Ensure Bluetooth on your smartphone has been turned on.
   • Your smartphone may be incompatible with the Govee Home app. Try using a different smartphone then reconnect.
   • Power the strip lights and your smartphone Bluetooth off then on, then try again.
   • Ensure that your smartphone is within 1 m/3.28ft of the strip lights when connecting.
   • Clear any obstructions that are between the strip lights and your smartphone.

3. The strip lights do not display the selected color fully/Some LED beads do not light up.
   Please contact the Govee support team for rapid product replacement.

4. Cannot sync the strip lights to the beat of my music.

   • Move the control box closer to the music source.
   • Clean the mic on the control box then try again.

5. The remote controller is not working.
   Press and hold the On/Off button on the control box for 3s. The strip lights will slowly blink blue and will enter pairing mode again. Press any button on the remote controller within 60s to begin pairing. When the strip lights rapidly blinks green 3 times, the pairing was a success. Pressing the control box again while pairing will exit pairing mode.

Customer Service
Warranty: 12-Month Limited Warranty
Support: Lifetime Technical Support e Email: support@govee.com
Official Website: www.govee.com
@Govee  @govee_official @govee.official  Govee official Govee. smart home

Compliance Information

EU Compliance Statement:
Shenzhen lntellirocks Tech Co. Ltd. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU.
A copy of the EU Declaration of Conformity is available online at www.govee.com/

EU contact address:
BellaCocool GmbH (E-mail: info@bellacocool.de) = PettenkoferstraBe 18, 10247 Berlin, Germany

Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

FCC Statement

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio Communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Non-replaceable light source.
Not intended for illumination. Only used for creating ambiance.

1. Do not connect the rope light to the supply while it is in the packing or wound onto a reel;
2. Do not use the rope light when covered or recessed into a surface;
3. Do not open or cut the rope light;

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Govee is a trademark of Shenzhen Intellirocks Tech Co.Ltd. Copyright ©2020 Shenzhen Intellirocks Tech Co.Ltd. All Rights Reserved

Frequency 2.4GHZ
Maximum Power 10dBm

References

• govee.com
• govee.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>