KYAMRC KY-1885AB 1:18 ABS Material Remote User Manual
- June 15, 2024
- KYAMRC
Table of Contents
KYAMRC KY-1885AB 1:18 ABS Material Remote
Product Information
Specifications
- Product : Car
- Refresh Methods : 3 kinds
- Scale : 1:16
- Frequency : 2.4 GHz
Product Usage Instructions
Refresh Methods
The car has 3 different refresh methods that can be used at any time. These
methods are designed to improve the overall performance and functionality of
the car.
-
Method 1:
Description of method 1 and how it refreshes the car. -
Method 2:
Description of method 2 and how it refreshes the car. -
Method 3:
Description of method 3 and how it refreshes the car.
Important Safety Instructions
Please follow these safety instructions to ensure proper usage of the car:
- Do not perform any actions that are specifically mentioned as “DO NOT” in the user manual.
- Pay attention to all warning signs and symbols on the car.
- Always keep your hands on the steering wheel and maintain full control of the car.
- Observe all traffic laws and regulations while operating the car.
- Regularly check and maintain the car’s brakes, tires, and other essential components.
Troubleshooting
If you encounter any issues with the car, please refer to the
troubleshooting section in the user manual or contact our customer support for
assistance.
BATTERY INSTALLATION
- Slide the battery cover off the compartment located at the bottom of the vehicle.
- Install batteries according to the (+) and (-) marks inside the battery compartment.
- Replace the battery cover.
REMOTE CONTROL
- Open the back cover of the remote control by turning the screw to the left.
- Install batteries according to the (+) and (-) marks in the battery compartment.
- Close the back cover of the remote control by turning the screw to the right.
CAUTIONS
- Always purchase the correct size and grade of battery most suitable for the intended use.
- Replace all batteries of a set at the same time.
- Clean the battery contacts and also those of the device prior to battery installation.
- Ensure the batteries are installed correctly with regard to polarity (+ and -).
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
ATTENTION
Users are not to make any changes or modifications to the equipment unless
expressly approved by the party responsible for compliance. Failure to observe
this instruction could void the user’s authority to operate the equipment.
**FCC INFORMATION
**
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
FAQ’s
How do I install the batteries in my RC car?
Slide the battery cover off the compartment located at the bottom of the vehicle, install the batteries according to the polarity marks, and replace the cover.
What type of batteries should I use?
Always purchase the correct size and grade of battery most suitable for the intended use, and do not mix different types of batteries.
What should I do if my RC car interferes with other electronic devices?
Try reorienting the receiving antenna, increasing the separation between the car and the affected device, or consult an experienced technician.
Are there any restrictions on modifying my RC car?
Users should not make any changes or modifications to the equipment unless expressly approved by the party responsible for compliance.
Can I use the refresh methods while driving?
No, it is not recommended to use the refresh methods while driving. It is advised to perform these actions when the car is stationary and parked in a safe location.
How often should I refresh the car?
The frequency of refreshing the car depends on various factors such as usage, environmental conditions, and maintenance. It is generally recommended to follow the guidelines provided in the user manual or consult with a professional mechanic.
Are there any specific precautions to take while using the refresh methods?
Yes, please ensure that you carefully follow the instructions provided in the user manual for each refresh method. Additionally, make sure to disconnect any external devices or accessories before initiating the refresh process.