FAREXON Electric Single Motor Standing Desk Instruction Manual
- June 14, 2024
- FAREXON
Table of Contents
Electric Single Motor Standing Desk
Instruction Manual
Electric Single Motor Standing Desk
Important-Please read these instructions before assembly.
If you encounter any problems during installation, please feel free to contact
us!
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician.
Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this
product for any purpose that is not explicitly specified in this manual and do
not exceed weight capacity. We cannot be liable for damage or injury caused by
improper mounting, incorrect assembly, or inappropriate use.
**** ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
- DONOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
- DONOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
- NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE DAMAGED PARTS.
- NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS,
- ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
- OUTDOOR USE IS PROHIBITED.
Components
If you encounter any problems during installation, please feel free to contact
us!
Part List
| Reference | Description | Part | Quantity |
|---|---|---|---|
| 1 | Desktop-a | 1 | |
| 2 | Desktop-b | 1 | |
| 3 | Left Leg | 1 | |
| 4 | Right Leg | 1 | |
| 5 | Support Beam | 2 | |
| 6 | Side Bracket | 2 | |
| 7 | Base | 2 | |
| 8 | Sync Rod | 1 |
Please check you have all the pieces listed below.
Notice!
When the screw is tightened, do not continue to tighten it forcefully,
otherwise the screw may be damaged.
Assembly Instructions
Step 1
Step 2
Step 3
Step 4
Step 5
Stand the table up and install two 6-Side Brackets. At the same time, the hooks can be installed together with the brackets, in any one of the four holes according to personal habits.
Step 6
Step 7
Firstly, insert the hexagonal rod into the main shaft of the table leg without motor and then lock the plastic nut.
Secondly, put the other side of the coupling rod into the pre-built rod on the motor leg and then lock the plastic nut again.
Note: Both ends of the sync rod should be inserted tightly into the end.
Step 8
Step 9
Step 10
Connect the hand controller, control box and power.
Use the D-Wire Clips to tidy up the wires.
DISPLAY INSTRUCTIONS
RESET Setting| Press and hold “ ” and “ ” buttons on the handset at the same
time for 4 seconds, it shows”000″,until you hear the beep release the buttons.
The desk will go down slowly automatically(it will have a rebound and rise
about 5mm)until it shows”69″and you hear the beep, the reset is successful.
---|---
Height Adjustment| Up: Press Up “ ” .Down: Press Down “ “
Switch Display| Press2 times “V” when the desk at the lowest position to
switch cm to inch.
Memory Height| Press and hold any of memory buttons (1,2,3or 4) until you hear
a beep. Release the button, and this position height will be stored in memory
When the working height of memory needs to be used, press the memory position
button and the desk will automatically adjust to the memory height.
Note: This tending desk has 4 different height memories The memory positions
stored are still valid after power of You can use the up and down buttons to
adjust the standing desk to the height you need to work.
Trouble shooting Guide:
If your standing desk does not work properly, you may need to reset it.
If any error codes appears, you need to reset it.
Unplug the power supply for 20s,then plug the power supply back in and the
desk will reset automatically. After it shows 69,the reset is done.
If it still does not work after the reset, please contact us for more help.
Maintenance and Consideration:
- During daily maintenance, use a clean soft cloth to remove surface dust. Do not use a wet cloth or hard material to wipe the surface of the table.
- Avoid contacting the surface with acid-based chemicals.
- For slight scratches, gentle wipe with a soft cloth, you can smooth out scratches. Avoid attaching tape directly to the outer surface of the metal feet to prevent paint from peeling.
MADE IN CHINA
Documents / Resources
|
FAREXON Electric Single Motor Standing
Desk
[pdf] Instruction Manual
Electric Single Motor Standing Desk, Single Motor Standing Desk, Motor
Standing Desk, Standing Desk, Desk
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>