FAREXON SANODESK Electric Single Motor Standing Desk Instruction Manual
- June 14, 2024
- FAREXON
Table of Contents
FAREXON SANODESK Electric Single Motor Standing Desk
Important: Please read these instructions before assembly.
If you encounter any problems during installation, please feel free to contact us!
IMPORTANT INFORMATION
- READ CAREFULLY.
- KEEP THIS INFORMATION FOR FURTHER REFERENCE.
GENERAL GUIDELINES
- Please read the following instruction carefully and use the product accordingly.
- Please keep this manual and hand it over when you transfer the product.
- This summary may not include every detail of all variations and considered steps.
- Please contact us when further information and help are needed.
NOTES
- Please follow the assembly instructions precisely and only use the product as intended.
- If an odor is present when first opening the package, please leave the unwrapped product in a shaded and ventilated area for a few days to air out.
- Prior to assembly, please check the product for defects or missing accessories. If any defects are found or accessories are missing, do not use product as damage or injury may occur;
- Please contact us for assistance and replacement.
- During assembly, please only slightly tighten all screws in their correct position first, then fully tighten them. A Philips screwdriver is recommended but not included.
- It is suggested you regularly check the products bolts and connections to ensure safe use.
- Assemble the item on a soft flat and clean surface to avoid scratches and damage.
WARNINGS
- During assembly, keep parts and packaging materials away from children and pets as there could cause injury and are a potential choking hazard.
- Avoid sharp objects or corrosive chemicals to prevent damage to the product.
- Please open the item slowly and cautiously to avoid pinching your hands by metal joints, especially for children.
Components
Please check you have all the pieces listed below
Weight
Tools
Notice: When the screw is tightened, do not continue to tighten it forcefully, otherwise the screw may be damaged.
Installation Instructions
Note: The horizontal bar on the iron connector should be perpendicular to the seam of the table panel splice.
- Install the another 6 -Support Beam on the other side in the same way as in step 3.
- Stand the desk up and install 7 -Side Brakets.At the same time,hooks can be installed to- gether with the brackets, in any one of the four holes according to personal habits.
- Install the 9-Sync Rod and tighten the two screws at the both end of Sync Rod.
- Install the frame on the desktop.
- Stand the desk up and press the outlet box firmly into the desk.
- Connect Controller,AC Adapter,Power Cable and Left Leg.
- Use D – Wire Clips to tidy up the wires.
CONTROLLER INSTRUCTION
RESET Setting| Method 1: Press and hold “ ” and “ ” buttons on the
handset at the same time for seconds until you hear the beep.Release the
buttons.The desk will goes automatically until it shows 69,and the reset is
successful.
---|---
Height Adjustment| Up: Press Up “ ” .Down:Press Down “ ” .
Switch Display| Press 2 times” “when the desk at the lowest position to switch
cm to inch
Memory Height| Press and hold any of memory buttons (1,2,3 or 4) until you
hear a beep.Release the button,and this position height will be stored in
memory.When the working height of memory needs to be used,press the memory
position button and the desk will automatically adjust to the memory height.
Note:This standing desk has 4 different height memories.The memory positions stored are still valid after power off.You can use the up and down buttons to adjust the standing desk to the height you need to work.
Troubleshooting And Maintenance
Troubleshooting Guide
- If your standing desk does not work properly, you may need to reset it.
- If any error codes appears, you need to reset it.
- Unplug the power supply for 20s, then plug the power supply back in and the desk will reset automatically. After it shows 69, the reset is done.
- If it still does not work after the reset, please contact us for more help.
Maintenance and Consideration
- During daily maintenance, use a clean soft cloth to remove surface dust. Do not use a wet cloth or hard material to wipe the surface of the table.
- Avoid contacting the surface with acid-based chemicals.
- For slight scratches,gentle wipe with a soft cloth, you can smooth out scratches. Avoid attaching tape directly to the outer surface of the metal feet to prevent paint from peeling.
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>