moofit HW401 Heart Rate Monitor Armband User Manual

June 14, 2024
moofit

USER MANUAL
ANT+ BLE Heart Rate Armband

Product Introduction

Thank you for purchasing our ANT+ & BLE heart rate armband, this product is one of the heart rate monitors of our company, which transmits the real-time heart rate data through
Bluetooth or ANT+ to heart rate receiving device, sports and health App, helping you to manage your exercise intensity scientifically. This user manual will help you to use the product better, please keep it for reference.
※(This product is for sport purposes only and it is not meant to replace any medical advice).

Product Accessories

moofit HW401 Heart Rate Monitor Armband - Product
Accessories

Charging

  1. Please charge the device before first time use;
  2. Please use DC 5V power adaptor for charging;
  3. When charging, LED will flash green and red alternately. Green light stay on means fully charged.

moofit HW401 Heart Rate Monitor Armband - Charging

Connect USB DC 5V power adapter or computer USB

The product has a built-in battery. Do not throw the product into a fire. Please select an adapter that meets the rated voltage of the device to charge the device to avoid damage to the device.

Function and Operation

moofit HW401 Heart Rate Monitor Armband - Function

Turn-on: Press the start-up button, the LED light will flash blue quickly until the heart rate was found, then the light will flash slowly;
Red light indicates the device is in a low battery state and needs to be charged.
Turn-off: Press the start-up button again, the LED will flash red and enter the shutdown state.
Wear the Heart Rate Sensor
Wearing the armband on the upper arm or forearm before using. It should not be too tight but avoid the sensor could move when training.

moofit HW401 Heart Rate Monitor Armband - Rate Sensor

Heart Rate Sensor Disassembly

  1. Press the front of the sensor to take out the sensor (Figure 1);
  2. Aligned with the raised position and stuck into the groove position to install the sensor (Figure 2).

moofit HW401 Heart Rate Monitor Armband - Rate Sensor1

Connection
Compatible with most third party fitness Apps ( Polar beat / Strada / Wahoo / Hear tool );
ANT+ connection to fitness equipments ( Treadmill/ sports watch / bike computer, etc.), detailed method reference to the corresponding equipment setting instructions;
This product Bluetooth and ANT+ transmission could work simultaneously.

Applicable models

iOS 9.0 version and above, iPhone 5s and above.
Any Bluetooth 4.0 enabled Android device with Android 4.3 and above.

Basic Parameters

Weight 7.7 g
Battery Life 20 hours for continuous heart rate monist
Wireless Rechargeable lithium battery
Power Bluetooth & ANT+
Working Temperature 0 ℃ ~ 45 ℃
Size 35.2 x 34 x 10.9 mm
Waterproof IP67

Disclaimer

The information contained in this manual just for reference. The product described above may be subject to alteration owing to the manufacturer’s continuing research and development plans, without making an announcement in advance.
We shall not bare any legal responsibility for any direct or indirect, accidental or special damages, losses and expenses arising from or in connection with this manual or the contained product.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals