VIGOPKA Keyless Entry Smart Door Lock Installation Guide

VIGOPKA Keyless Entry Smart Door Lock

Product Information

Specifications

• Smart lock: 1
• Latch: 1
• Batteries: 4
• Key fobs: 2
• Physical keys: 2
• Box striking plate: 1
• Mounting plate: 1
• Protective pad: 2
• Lock cylinder: 1
• Nuts: 3
• Screws: 9

Product Usage Instructions

Dimensioning

Before drilling the hole, please check the dimensions and follow the instructions below:

Backset:

• 2-3/8 or 2-3/4 (60-70mm)

Door Hole Diameter:

• 2-1/8 (54mm)

Hole on Door Side Diameter:

• 1 (25mm)

Door Thickness:

• 1-3/8 to 2 (35 to 50mm)

Fixing the Lock for Left or Right Opening Way

Note : The initial state of the smart lock handle is suitable for right- opening doors.

1. Move the handle downward at a 45-degree angle until you see the screws inside.
2. Unscrew the screws.
3. Move the handle 270 degrees backward.
4. Screw the screws back in until you see the screw holes.

In this way, the shift from left/right opening way is done.

Inserting the Lock Tongue

• Trim Size: 3/4 (19mm)
• Screw: 2
• Proceed to the next step without adjustment.
• Pinch and pull the square hole to adjust the length of the lock tongue.

Installing the Buckle Box on the Door Frame

• Trim Size: 3/4 (19mm)
• Screw: 2
• The door frame holes should be drilled at least 1/2 (12mm) deep.

Installing the Door Lock

1. Fit the rubber pad on the outer panel and tighten the 3 screw pipe strings.
2. Fix the lock cylinder according to the left or right opening way. Make sure the triangle arrow on the lock cylinder groove corresponds with the left or right door-opening direction you want to set.
3. Pass the outer panel power cord through the door hole and out from the other side.
4. Fit rubber pad on the metal retaining plate beneath the lock as shown in the picture, then screw the three long screws into the corresponding holes.
5. Connect the two terminals. Check the positive and negative of the plug before using. Do not forcibly insert or remove the plug to avoid damage.
6. Fix the back panel with screws one by one.
7. Insert the battery, close the battery cover, and complete the installation.

Frequently Asked Questions (FAQ)

• Q: How many batteries are included?
  A: Four batteries are included with the product.

• Q: How many key fobs and physical keys are included?
  A: The product includes two key fobs and two physical keys.

• Q: What is the backset dimension for the lock?
  A: The backset dimension can be either 2-3/8 (60mm) or 2-3/4 (70mm).

• Q: What is the recommended door thickness for installation?
  A: The recommended door thickness is between 1-3/8 to 2 inches (35 to 50mm).

Installation Instructions

1. Smart lock*1
2. Latch*1
3. Batteries * 4
4. Key fobs*2
5. Physical keys*2
6. Box striking plate*1
7. Mounting plate*1
8. Protective pad*2
9. Lock cylinder*1
10. Nuts*3
11. Screws*9

Dimensioning

Before drilling the hole, please check the dimensions and follow the instructions below

1. Measure to verify that the hole on the door is 2-1/8″ (54mm) in diameter
2. Make sure the distance from the edge of the door to the center of the hole is 2-3 / 8 ” ( 60mm ) or 2-3 / 4 ” ( 70mm )
3. Check if the hole on the door side is 1 ” ( 25mm ) in diameter as the picture shows
4. The thickness of the door should be 1-3 / 8 ” to 2 ” ( 35 to 50mm )

How to fix it alternatively from the left opening to the right opening way

Note : The initial state of the smart lock handle is suitable for right- opening doors

• First, move downward the handle at 45 degrees till you see the screws inside
• Secondly, unscrew the screws
• Thirdly, move the handle 270-degree backward till you see the screw holes
• Screw the screws back
• In this way, the shift from left /right opening way is done

Insert the lock tongue

Install the buckle box on the door frame

Install door lock

1. Fit the rubber pad on the outer panel , and tighten the 3 screw pipe strings
2. Fix the lock cylinder to comply with the left or right opening way. Make sure the triangle arrow on the lock cylinder groove corresponds with the left or right door-opening direction you want  to set
3. Pass the outer panel power cord through the door hole and out from the other side
4. Fit the rubber pad on the metal retaining  plate beneath the lock as the picture shows, then screw the three long screws into the corresponding holes
5. Connection of the two terminals. Check the positive and negative of the plug before using it. Do not forcibly insert or remove the plug to avoid damage
6. Fix the back panel with screws one by one
7. Insert the battery, close the battery cover, and complete the installation

Important
Please pay attention to step 2 of the installation of the lock, the set  of left/right opening issue

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>