Waterpik CC-01 Water Flosser Electric Toothbrush User Manual

Waterpik CC-01 Water Flosser Electric Toothbrush

BEFORE USING

• This product is for household use.
• When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:

DANGER:

To reduce the risk of electrocution:

• Do not handle the plug with wet hands.
• Do not place in or drop into water or other liquid.
• Do not use it while bathing.
• Do not place or store product where it can fall or be pulled into a tub or sink.
• Do not reach for a product that has fallen into the water. Unplug immediately.
• Check the power supply cord for damage before the first use and during the life of the product.

WARNING:

To reduce the risk of burns, electrocution, fire, or injury to persons:

• Do not plug this device into a voltage system that is different from the voltage system specified on the device or charger. Use with improper voltage will damage the product and VOID warranty.
• If the product is opened/disassembled for ANY reason warranty is VOID.
• Do not use this product if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water.

Contact Water Pik, Inc. at 1-800-525-2774 or visit www.waterpik.com

• Do not direct water from the Water Flosser under the tongue, into the ear, nose, or other delicate areas. This product is capable of producing pressures that may cause serious damage in these areas.
• Do not direct water into the nose or ear. The potentially deadly amoeba, Naegleria fowleri may be present in some tap water or unchlorinated well water and may be fatal if directed into these areas.
• Use this product only as indicated in these instructions or as recommended by your dental professional.
• Only use tips and accessories recommended by Water Pik, Inc.
• Do not drop or insert any foreign object into any opening or hose.
• Keep the electrical cord away from heated surfaces.
• Do not use a Water Flosser or Toothbrush outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
• Do not use iodine, or water-insoluble concentrated essential oils in the Water Flosser. Use of these can reduce product performance and shorten the life of the product.
• Remove any oral jewelry prior to the use of the Water Flosser or Toothbrush.
• Do not use either the Water Flosser or Toothbrush if you have an open wound on your tongue or in your mouth.
• If your physician or cardiologist has advised you to receive antibiotic premedication before dental procedures, you should consult your dentist and/or medical professional before using the Water Flosser, Toothbrush, or any other oral hygiene aid.
• This product complies with the safety standards for electromagnetic devices.
• If you have a pacemaker or other implanted device containing magnets or electronics, contact your physician or the device manufacturer prior to using the Toothbrush.
• If the Pik Pocket™ tip (not included in all models) separates from the shaft for any reason, discard the tip and shaft and replace it with a new Pik Pocket™ tip.
• Do not use the Water Flosser for more than 5 minutes in each two-hour period.
• This product does not contain any user-serviceable parts in the toothbrush handle or Water Flosser unit.
• Do not attempt to open either component except for battery disposal.

See Battery Removal Section.

• Using toothpaste containing peroxide may damage the plastic housing of this product.
• Using abrasive or chemical cleaners may damage the plastic housing of this product.
• Close supervision is necessary when this product is used by, on, or near children or invalids.
• Children should be supervised to ensure that they do not play with the appliance.
• Fill the Water Flosser reservoir with warm water or other dental professional-recommended solutions only.

PRODUCT DESCRIPTION

Water Flosser

• Hinged reservoir lid
• Reservoir
• Hose
• Water fosser pressure control dial
• Power button (push to turn unit ON/OFF)
• Power cord
• Magnetic handle cradle
• Tip
• Tip eject switch
• Water ON/OFF switch
• Toothbrush charger post
• Base

TIPS

• Orthodontic Tip – Braces – General use
• Pik Pocket™ Tip – Periodontal pockets – Furcations
• Plaque Seeker™ Tip- Implants – Crowns – Bridges- Retainers – General use
• Classic Jet Tip – General use
• Tongue Cleaner- Fresher breath

NOT ALL TIPS INCLUDED IN ALL MODELS

Sonic/Oscillating Toothbrush

• Sonic brush head
• Oscillating brush head
• Toothbrush power button
• Toothbrush mode button
• Toothbrush mode indicator lights
• Toothbrush recharge indicator

Brush Heads

• Triple Sonic Brush Head”
  • Plaque removal
  • Whitening
• Triple Clean (Oscillating) Brush Head
  • Raque removal

NOTE : BRUSH HEADS ARE NOT INTERCHANGEABLE. EACH UNIT ONLY CONTAINS ONE TYPE OF TOOTHBRUSH.

Replacement tips/attachments may be purchased online at www.waterpik.com or by phone from Water Pik, Inc. at 1-800-525-2774. To find detailed information about tips, other accessories, and product usage please visit our website at www.waterpik.com

GETTING STARTED WITH YOUR WATER FLOSSER

Powering the Unit
Plug the cord into an electrical outlet. If the outlet is controlled by a wall switch, be sure it is turned on.

Preparing the Reservoir
Lift the reservoir lid, remove the reservoir, and fill it with lukewarm water. Replace the reservoir over the base press down firmly and close the lid.

Inserting and Removing Tips
Insert the tip into the center of the Water Flosser handle, pressing down firmly until the tip clicks into place. The colored ring will be flush with the top of the handle if the tip is correctly locked into place. To remove the tip from the handle, slide the tip eject button on the handle.

Caution : Do not use the tip-eject slide while the unit is running.

Prime Unit (First Time Use Only)
Set the pressure control dial on the base to high (pressure setting No. 10), and point the handle and tip into the sink. Turn unit ON (I) and water ON until water flows from the tip. Turn Power Off (0).

Adjusting the Pressure Setting
Turn the pressure control dial on the base of the unit to the lowest setting (pressure setting No. 1) for first-time use. Gradually increase pressure over time to the setting you prefer – or as instructed by your dental professional.

Using the Water Flosser
Always place the tip in your mouth before turning the water ON. With the water switch in the OFF position, turn the power on. Lean over the sink and slightly close your lips enough to prevent splashing while still allowing water to flow from your mouth into the sink. Turn the water switch ON. When finished, turn the water switch and power OFF. During use, you can stop the flow of water by sliding the water switch on the handle to the OFF position.

NOTE : The motor will continue to run.

Recommended Technique
For best results, start with the back teeth and work toward the front teeth. Glide the tip along the gumline and pause briefly between teeth. Continue until you have cleaned the inside and outside of both the upper and lower teeth.

When Finished
Turn the unit OFF (O). Empty any liquid left in the reservoir. Unplug the unit.

NOTE : If you used mouthwash or other solution besides water, see the “Using Mouthwash and Other Solutions” section.

NOTE : NOT ALL TIPS INCLUDED WITH ALL MODELS.

TIP USAGE

Plaque Seeker™ Tip
To use the Plaque Seeker™ tip, place the tip close to the teeth so that the bristles are gently touching the teeth. Gently glide the tip along the gumline, pausing briefly between teeth to gently brush and allow the water to flow between the teeth.

Orthodontic Tip
To use the orthodontic tip, gently glide the tip along the gumline, pausing briefly to lightly brush the area between the teeth and all around the orthodontic bracket, before proceeding to the next tooth.

Pik Pocket™ Tip
The Pik Pocket™ tip is specifically designed to deliver water or anti- bacterial solutions deep into periodontal pockets. To use the Pik Pocket™ tip, set the unit to the lowest pressure setting. Place the soft tip against a tooth at a 45-degree angle and gently place the tip under the gumline, into the pocket.

Tongue Cleaner Tip
Set to the lowest pressure setting, place the tip in the center/middle of your tongue about halfway back. Pull forward with light pressure. Increase pressure as you prefer

Using Mouthwash and Other Solutions
Your Waterpik® Water Flosser can be used to deliver mouthwash and antibacterial solutions. After using any special solution, rinse the unit to prevent clogging by partially filling the reservoir with warm water and running the unit with a tip pointed into the sink until the unit is empty.

Cleaning
Before cleaning, unplug from the electrical outlet. Clean the product when necessary by using a soft cloth and mild non-abrasive cleanser. The water reservoir is removable for easy cleaning and is top-rack dishwasher safe.

Removing Hard Water Deposits / General Cleaning
Hard water deposits may build up in your unit, depending on the mineral content of your water. If left unattended, it can hinder performance.

Cleaning internal parts:

add 2 tablespoons of white vinegar to a full reservoir of warm water. Point the handle and tip into the sink. Turn the unit ON and run until the reservoir is empty. Rinse by repeating with a full reservoir of clean warm water. This process should be done every 1 to 3 months to ensure optimal performance.

Leakage
If leaking due to a damaged hose, replacement hoses, and handles can be purchased at www.waterpik.com or contact Water Pik Inc. customer service for a self-service repair kit.

GETTING STARTED

Charging the Triple Sonic Toothbrush
Charge for 24 hours before first use. All 3 charge indicator lights will stay on continuously when the unit is fully charged. A full charge will last for approximately 1 week of typical use (2 minutes of brushing twice a day). If the toothbrush is to be stored for an extended period of time (six months or more), be sure to fully charge it prior to storage.

Recharge Indicator Lights
Charge indicator lights will indicate the level of battery charge for approximately 10 seconds after use and after removal from the charging base, and will then turn off.

• Fully Charged
• 2/3 Charged
• 1/3 Charge Life (Recharging is Recommended)

The unit will not operate if the bottom LED begins to blink rapidly. In order for the toothbrush to begin to work again, it must be placed on the charger for approximately 1 hour.

Modes

• Clean : Standard mode for superior teeth cleaning.
• Whiten : Teeth cleaning with polishing and whitening.
• Massage : Pulsates for gentle gum stimulation

Sonic brushing

• Slide the brush head onto the handle and push it down firmly.
• Place the brush head into your mouth before turning the unit on.
• Select mode by pressing the mode button.
• For best results, position the brush along the gumline at a 45-degree angle.
• Use light pressure with a small, slow back-and-forth motion covering one or two teeth at a time.
• Quad Timer: The Toothbrush will create a short pause every 30 seconds, to remind you to move to the next quadrant of your mouth.
• 2-Minute Timer: The brush will automatically shut off after 2 minutes of run time.

GETTING STARTED WITH YOUR OSCILLATING TOOTHBRUSH

Charging the Triple Clean Toothbrush
Charge for 24 hours before first use. When the toothbrush is fully charged, the charge indicator will be green while sitting on the base. A full charge will last for approximately 1 week of typical use (2 minutes of brushing twice a day). If the toothbrush is to be stored for an extended period of time (six months or more), be sure to fully charge it prior to storage.

Recharge Indicator Lights
Charge indicator lights will indicate the level of battery charge for approximately 10 seconds after use and after removal from the charging base, and will then turn off.

• Fully Charged – CHARGE light is green.
• 2/3 Charged – Both MASSAGE and LOW lights are flashing green.
• 1/3 Charge life – MASSAGE light is green. Recharging is recommended.

NOTE :

• If the charger light blinks red and green when the charger base, the unit has a low battery level and may not operate.
• In order for the toothbrush to begin to work again, it must be placed on the charger for approximately 1 hour.

Modes

• High : Everyday cleaning performance
• Low : Gentle movements for effective cleaning of sensitive teeth
• Massage: Micro-pulse pattern for enhanced gum stimulation

Brushing

• Slide the brush head onto the handle and push it down firmly.
• Place the brush head into your mouth before turning the unit on.
• Select mode by pressing the mode button.
• Use light pressure with a small, slow back-and-forth motion covering one or two teeth at a time.

Quad Timer: The Toothbrush will create a short pause every 30 seconds, to remind you to move to the next quadrant of your mouth.

2-Minute Timer : The brush will automatically shut off after 2 minutes of run time.

CARE OF YOURWATERPIK® TOOTHBRUSH

Cleaning

• After each use, turn off the unit, remove the brush head from the handle, and rinse the brush head under running water.
• Wipe the handle dry after each use.

Service Maintenance
Waterpik® Toothbrushes have no consumer serviceable electrical items and do not require routine service maintenance. For all accessories go to www.waterpik.com. You may also call our toll-free customer service number at 1-800-525-2774 (USA) or 1-888-226-3042 (Canada). Refer to the serial and model numbers in all correspondence. These numbers are located on the bottom of your unit.

Still have questions? Go to www.waterpik.com

DISPOSAL AND BATTERY REMOVAL

Disposal
This product contains rechargeable Nickel Metal Hydride batteries. The batteries are not replaceable. Please do not dispose of the unit in the household waste. Remove the batteries per the instructions below and recycle at your local recycling center.

Battery Removal

Note: This process is not reversible Remove the battery only at the end of the product’s life for recycling. Doing so earlier will destroy the product. Deplete the battery charge until the brush no longer operates. Observe basic safety precautions. Remove the batteries as shown and recycle them and the rest of the product according to local regulations.

• Use a screwdriver to remove the screw and battery door.
• Hold the handle upside down, press the toothbrush shaft, and release the two tabs inside the handle using a flathead screwdriver to release the internal components of the handle.
• Insert a screwdriver next to the battery connections, and push out of the plastic covering. Twist and break the battery connections. Remove the circuit board and pry the battery from the circuit carrier.
• Recycle or dispose of the battery properly.

WARRANTY

LIMITED TWO-YEAR WARRANTY

Water Pik, Inc. warrants to the original consumer of this product that it is free from defects in materials and workmanship for 2 years from the date of purchase. Consumers will be required to submit the original purchase receipt as proof of purchase date and if requested, the entire product, to support a warranty claim. Water Pik, Inc. will replace at its discretion any part of the product, which in its opinion is defective, provided the product has not been abused, misused, altered, or damaged after purchase, was used according to instructions, and was used only with accessories or consumable parts approved by Water Pik, Inc. Installation is the responsibility of the consumer and is not covered by the warranty. This limited warranty excludes accessories or consumable parts such as tips and brush heads. Use with improper voltage will damage the product and VOID warranty. This warranty gives you specific legal rights. You may also have other rights that vary, depending on the law in your place of residence

Service Maintenance

Waterpik® Water Flossers have no consumer serviceable electrical items and do not require routine service maintenance. For all accessories go to www.waterpik.com. You may also call our toll-free customer service number at 1-800-525-2774 (USA) or 1-888-226-3042 (Canada). Refer to the serial and model numbers in all correspondence. These numbers are located on the bottom of your unit. Still have questions?

Go to www.waterpik.com

FAQs

What is the TEASÄNE Mosquito Bug Zapper Light Bulb?

The TEASÄNE Mosquito Bug Zapper Light Bulb is a lighting solution designed to attract and eliminate mosquitoes and other flying insects while providing illumination.

How does the mosquito bug zapper feature work?

The bug zapper feature typically uses UV light to attract insects and an electric grid or trap to eliminate them when they come into contact with it.

What types of insects does this light bulb target?

The TEASÄNE Mosquito Bug Zapper Light Bulb is designed to target mosquitoes and various flying insects commonly found outdoors.

Is this light bulb suitable for indoor and outdoor use?

This light bulb is typically designed for outdoor use, where mosquitoes and bugs are most prevalent. However, some models may be used indoors as well.

What is the lifespan of the TEASÄNE Mosquito Bug Zapper Light Bulb?

The lifespan of the bulb may vary depending on usage, but it is often designed to last for thousands of hours before replacement is needed.

Is the bug zapper function safe for humans and pets?

The bug zapper function is typically designed to be safe for humans and pets, but it's essential to follow safety guidelines provided by the manufacturer.

Does the light bulb require any special installation or fixtures?

Installation is usually as simple as screwing in the bulb like a regular light bulb. It may fit standard light fixtures.

Is the light bulb energy-efficient?

Many mosquito bug zapper light bulbs are designed to be energy-efficient, helping to reduce electricity consumption.

Is the bulb resistant to weather and moisture?

The bulb is typically designed to be weather-resistant and withstand outdoor conditions, including rain and humidity.

Can it be used as a primary source of outdoor lighting?

Some models may provide sufficient illumination for outdoor areas, while others are primarily designed for bug zapping with minimal lighting.

Does it emit any noise or odors when insects are zapped?

The bug zapper function is typically quiet and odorless, ensuring a comfortable outdoor environment.

Can I use this light bulb in existing outdoor fixtures?

Yes, the TEASÄNE Mosquito Bug Zapper Light Bulb is often compatible with standard outdoor light fixtures, making it easy to install.

Video Introduction

Download This PDF Link:Waterpik CC-01 Water Flosser Electric Toothbrush User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>