CURSOR FITNESS C20 Under Desk Treadmill 2 in 1 Walking Pad User Manual
- June 14, 2024
- CURSOR FITNESS
Table of Contents
CURSOR Fitness
C20 Treadmill
User’s Manual
Important Precaution
MINIMUN
USER
HEIGHT| 140 cm| MAX
USER
WEIGHT| 265 Lbs
---|---|---|---
WARNING
CORRECT LUBRICATION OF THE TREADMILL IS REALLY IMPORTANT. THIS LUBRICATION
MUST BE PERFORMED REGULARLY DEPENDING ON EACH PERSON, EVEN BEFORE ITS FIRST
USE.
YOU MUST PRESERVE THE ORIGINAL PACKAGING WITH ITS PROTECTIONS, PURCHASE
RECEIPT, MANUAL, AND COMPONENTS DURING THE GUARANTEE PERIOD.
In order to decrease the risk of suffering severe injuries, read carefully all
the important instructions and warnings regarding the use of a treadmill
before using it.
CURSOR FITNESS doesn’t take any responsibility for personal injuries or
property damages resulting from the use of this product.
-
Before starting any workout program, consult your doctor. It’s especially important for people older than 35 years old, people with a health problem, and pregnant women.
-
Use the equipment as explained in the instructions manual.
-
Keep the equipment in an enclosed area, away from dust or humidity. Don’t store it in a garage, indoor backyard, or near the water. Humidity, dust and water could lead to a malfunction of the equipment, annulling its guarantee.
-
Place the unit on a flat surface. If the surface is uneven, the proper functioning could be affected. Some models include levelers or leveling threads behind the legs, helping the
leveling. Please read the manual to verify if your unit is provided with one of them… -
The unit must be placed in a ventilated area. Don’t use it in places with sprays or oxygen dispensers. The air you breathe may be affected and cause an accident.
-
Keep children younger than 12 years old and pets away from the equipment. Keep the security distance.
-
Check in the manual the maximum weight your equipment can support. Excessive weight could lead to a malfunction in the operating system, which won’t be covered by the guarantee.
-
If your equipment is working through a power supply: make sure that the power cord and plug are in good condition. Carry out the connection only when the circuit has a ground connection, otherwise, it could cause damages to the equipment or in the property which the guarantee won’t cover. Power cords must be away from hot surfaces.
-
If it is a battery-powered unit: check and make sure that they are charged enough so the display will fully function.
-
If your unit works with an electric supply: check the speed it can reach, for your security. The best is to adjust gradually the speed in order to avoid sudden changes.
-
If your unit works through an electric supply: never leave the machine unattended while it’s working.
-
Check and tighten all screws on a regular basis, because due to vibrations screws and nuts tend to loosen. Damages caused by a lack of maintenance won’t be covered by the guarantee.
-
Two people will be needed in order to take the unit from the package. Otherwise, the damages caused at this moment won’t be covered by the guarantee.
-
Don’t let any object fall into the grooves.
-
If the unit works through a power cord: unplug always the power cord before cleaning it, after the workout, and before performing any maintenance duty.
-
If you start feeling pain or dizziness while training: STOP IMMEDIATELY.
-
You must preserve the original packaging with its protections, manual, and components during the guarantee period.
-
This electronic product can’t be thrown under any circumstances into municipal rubbish bins. With the aim of preserving the environment, this product must be recycled according to the applicable law of your country. Please contact your town council to know more about this procedure.
-
Should you need technical assistance or advice with the installation of pieces, You can get in touch with us through 866-950-8629.
YOU MUST KEEP THE PURCHASE RECEIPT IN ORDER TO HAVE ACCESS TO THIS SERVICE KEEP THIS ADVICE FOR FUTURE REFERENCES
Main Technical Features
| Input Voltage | 110V±10% |
|---|---|
| Frequency | 60 HZ |
| Running Area | 39.8″ x 15.4″ |
| Function | Remote control, Bluetooth, APP |
| Speed Range | 0.6-3.9MPH |
| Max user weight | 265 Lbs |
| Power | 2.5 HP |
Assembly
Plug and Play, No assemble needed
| No. | Fittings | Qty |
|---|---|---|
| 1 | Remote Control | 1 |
| 2 | Lubricant | 1 |
| 3 | Multi- wrench | 1 |
| 4 | 5mm wrench | 1 |
| 5 | 6mm wrench | 1 |
| 6 | CR2032 Lithium Battery | 1 |
Workout Guidelines
Beware:
Before starting to use this or any exercise programs, consult your doctor.
This is especially important for people older than 35 years old, or for people
with health problems.
Programm with warm-up workouts:
Warm-up: Start stretching and slightly activating the muscles between 5 and 10
minutes. The warm-up will increase your corporal temperature, your heart rate,
and your blood flow, making you ready for the workouts.
- WORKOUT FOCUSED ON THE TRAINING AREA: Do some exercises during 20-30 minutes with your heart rate (don’t maintain your heart rate for more than 20 minutes during the first weeks of the exercise program). Breathe constantly and deeply during the workout (never hold your breath).
- COOL DOWN: Finish with stretching exercises during 5-10 minutes. Stretching increases the flexibility of your muscles and helps you to avoid injuries after the workouts.
FREQUENCY OF THE WORKOUT:
In order to be fit or improve your shape, complete three workout sessions
each week, with a rest day between the workouts. After some months of regular
training, you will be able of completing up to five workouts a week.
Treadmill Operation
A brief introduction
This electronic watch is easy to use and has few adjustment parameters The
noun convention used in the specification:
Treadmill parameters: “Speed” values Motion parameters: “distance” value,
“calorie” value, “time” value. Motion mode: wireless receiving control mode
LED screen display description:
- Speed display: When this LED is on, the screen displays the current speed value.
- Time display: When this LED is on, the screen shows the current time value.
- Distance display: When this LED is on, the screen shows the current distance value.
- Calorie display: When this LED is on, the screen shows the current calorie value of the exercise.
The above parameters are displayed at intervals of about 5 seconds.
This product is a wireless remote control, and the Settings are as follows:
- Start button: Press the start button on the remote control and the treadmill belt begins to move.
- Pause button: Press the pause button on the remote control to pause the treadmill belt’s movement. The display window will show “PAU” and pause the current time, distance, calories, speed, etc. Press the start button on the remote control to continue the current status and resume exercising.
- Speed +: Press the speed + button on the remote control to increase the exercise speed.
- Speed -: Press the speed – button on the remote control to decrease the exercise speed.
- P button: Press the P button on the remote control to switch the display window between exercise speed, time, distance, and calories.
- Power button: Press the power button on the remote control to start exercising.
- Stop button: Press the stop button on the remote control to stop exercising.Please note that if the movement time exceeds 99 min 59s, the system will stop automatically.
Trouble Shooting
| Error Code | Reason | Solution |
|---|---|---|
| E01 | Communication error | Re-plug each plug of the signal line |
Replace the electronic meter
Replace the driver
E02| Sensor detection error| Detect sensor route
Change motor
Change PCB
E03| Over current protection| Change PCB
E04| Sudden big current protect| Check the AC power
supply voltage
Change PCB
E05| Sudden low current protect| Check the AC power
supply voltage
Change PCB
E06| Overload error| Check running belt
resistance
Change motor
Change PCB
E08| PCB overheat protection| Check running belt
resistance
Change PCB
E09| Motor testing error| Turn off and re-start
machine Change motor
E11| Motor wire not well connected| Check motor wire
Change PCB
Change motor
E12| PCB error| Change PCB
E13| Computer error| Check connection wire
Change PCB
Change computer
E14| Phase failure error| Re-plug the phase wire
into the drive
Power off and on
Replace the motor
E16| Drive failure| Replace the motor
The Obvious Danger List
| No. | Description | Associated |
|---|---|---|
| 1. | Mechanical Hazards | |
| 1.1 | Crushing | Inclining |
Folding
1.2| Shearing| Inclining
Folding
1.3| Drawing-in Or Trapping| Rear roller
Drive system
1.4| Falling| Sudden starts/stops
Excessive speed variation
Support failure
1.5| Abrasion| Contact with moving running surface
1.6| Slippery Surface| Slipping and falling
1.7| Stored Energy| Folded treadmills falling down
Springs or elastic devices prior to assembly
2.| Electrical Hazards|
2.1| Electrocution| Contact with live components
3.| Thermal Hazards|
3.1| Burns| Contact with hot surfaces
4.| Hazards generated by neglecting ergonomic
principles in design process|
4.1| Ineffective ergonomics| Size or location of support surfaces
Running surface dimensions
4.2| Human errors human behaviour| Reasonably foreseeable misuse
5.| Noise Hazards|
5.1| Disturbing acoustic communication| Moving treadmill motor and belt
Maintenance
This product must be earthed. If the power cord is damaged, it must be replaced with a manufacturer-recommended power cord.
DO NOT TANGLE THE POWER CORD
Regular maintenance of the treadmill
- STORAGE: Keep your equipment in an enclosed place, away from dust or humidity. Don’t store it either in a garage or in an indoor backyard, or near the water. Humidity, dust, and water could damage it and affect its functioning
- ELECTRIC CABLE: Make sure that the cable and plug are in perfect condition. Electric cables must be away from hot surfaces
- SCREWS AND CONNECTING CABLES: Supervise and tighten the screws on a regular basis, because due to the vibration the screws and nuts tend to loosen.
Lubrication: After running for a period of time, the treadmill must be configured with lubricants for lubrication.
Schedule:
| < 3 hours/week | 2 months |
|---|---|
| 4 – 7 hours/week | 1 month |
| > 8 hours/week | 15 days |
*Do not lubricate more than what you need to. Remember: regular and reasonable lubrication is to improve the lifespan of your treadmill.
Whether it is necessary to lubricate, make sure the machine is switched off
and unplug the electricity. Lift the running belt, and observe if there is any
silicon remaining on the running board which is under the running belt. If it
is dry, then you need to apply the lubricant.
a) The step to lubricate the running board is as follows: (see the above
figure)
b) Stop the running belt.
c) Turn over the running belt. Insert the lubricant pot as deep as possible
into the middle of the running belt. Apply the lubricant onto the inner side
of the running belt. Lubricate both sides of the running belt. After the
lubrication is completed, start the machine at 1km/h to let the running belt
bring silicon all over the board.
Align and tighten the treadmill belt
- ALIGN THE BELT: Due to its use, the belt can move off-center. If the belt has moved to the left, start the treadmill and increase the speed to 3 MPH. Use the 5mm Wrench to turn the fixed left bolt clockwise or turn the fixed right bolt counterclockwise. Don’t tighten the belt too much in order to be able to walk.
Repeat this procedure until the belt is properly aligned.
- TIGHTEN THE BELT: (if the belt slips on the treadmill when walking). Start treadmill and increase the speed to 3 MPH. Using the 5mm wrench, turn both bolts 1/4 clockwise. If the belt is properly tight to walk, you must be able to pull up each side of the belt 5 or 7 cm off the platform. Be careful and maintain the belt aligned. Repeat this procedure until the belt is properly tightened.
• TIGHTEN THE DRIVE BELT:
If the drive belt becomes loose after using it for a period of time, you need
to:
(1) Open the motor cover.
(2) Use the 5mm wrench to turn the adjusting bolt clockwise.
Repeat this procedure until the drive belt is not slippery anymore.
- CLEANING: Don’t use abrasive products, a damp cloth is enough.
- LEVELING: If your unit is provided with leveling wheels, please adjust them in order to avoid vibrations and therefore malfunctions.
- KEEP THESE MAINTENANCE ADVISES FOR FUTURE REFERENCES
CURSOR CARE
**** This electronic product must not be disposed of in municipal waste. To preserve the environment, this product must be recycled after its useful life as required by law.
Contact Cursor 7/24 response
√ 7*24 online California-based customer service team to solve after-sales
problems without obstacles
√ Return Policy: 30-Day Hassle-Free Return and Exchange
√ Customer Service: California-Based Service Team Providing personalized
solutions to ensure 100% customer satisfaction
√ Exclusive Maintenance Service: We honor our commitment to quality and
durability by offering free maintenance tools for orders within 6 months,
including lubricants and remote control
Contact Number：866-950-8629
CursorCare Team E-Mail：cursorcare@outlook.com
You must preserve the original packaging with its protections, purchase
receipt, manual and components during the guarantee period.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>