PPEpower HD 10R140 Aluminum Transmission Pan Installation Guide

June 14, 2024
PPEpower

Heavy-Duty Cast Aluminum
Deep Transmission Pan
Ford Super Duty 10R140 Transmission
(328053300, 328053310, 328053320)
Installation Guide

HD 10R140 Aluminum Transmission Pan

PPEpower HD 10R140 Aluminum Transmission Pan

PPEpower HD 10R140 Aluminum Transmission Pan - pARTS

CONTENTS

A (20) M6-1.0 x 25mm Socket Head Cap Screws
B (20) M6 Flat Washers
C (1) 1/8-inch NPT plug (installed)
D (1) Neodymium Magnetic Drain Plug (installed)
E (1) PPE Deep Transmission Pan
Step 1. Vehicle off and secure. Engine cool.
Step 2. Remove rearward screws that secure the factory pan. Fluid will begin to drain. Loosen side screws to increase fluid flow. Doing this will minimize the volume of remaining fluid when pan is removed. Remove the remainder of the screws and remove the stock pan. Be cautious of the fluid remaining in the stock pan. Retain OEM gasket. Recycle fluid.
Step 3. Carefully clean OEM gasket.
Step 4. Thoroughly clean mating surface.
Step 5. Install a new set of OEM gasket in the channel, align the two halfmoon shapes on the gasket and the channel. Be careful to not install the gasket upside down (FIG 1)
Step 6. Assemble the 20 M6 screws and washers for easier installation.
Step 7. Lift PPE Pan into position and thread two M6 screw and washer assemblies into opposite sides of the Pan to hold in place. Finger tight for now.
Step 8. Install remaining M6 screw and washer assemblies. Finger tight for now.
Step 9. Tighten M6 screw assemblies in a crossing pattern as shown. (FIG 2) Torque to a final spec of 8-10 ft lbs.
Step 10. Check that the Drain Plug and NPT Plug are tight.
Step 11. Fill with recommended fluid.  Start engine. Check for leaks.
Installation complete.

PPEpower HD 10R140 Aluminum Transmission Pan - Fig1

DISCLAIMER OF LIABILITY

Performance products can increase horsepower above and beyond factory specifications.
Additional horsepower creates more stress on the drive-train components, which could result in drive-train failure.
Note regarding emissions-related, non-E.O.-legal products: THESE PRODUCTS ARE LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE.
This agreement sets forth the terms and conditions for the use of PPE products. The installation of this product indicates that the Buyer has read and understands this agreement and accepts the terms and conditions. PPE (Pacific Performance Engineering) Inc., its distributors, employees, and dealers (the “Seller”) shall not be responsible for the product’s proper use and service. The buyer hereby waives all liability claims. The Buyer hereby acknowledges no reliance on the Seller’s skill or judgment to select or furnish goods suitable for any particular purpose and that there are no liabilities which extend beyond the description on the face hereof, and the Buyer hereby waives all remedies or liabilities expressed or implied, arising by law or otherwise (including without any obligation of the Seller with respect to fitness, merchantability and consequential damages), or whether or not occasioned by the Seller’s negligence.
The Seller disclaims any warranty and expressly disclaims any liability for personal injury or damages. The Buyer acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and the Buyer agrees to indemnify the Seller and to hold the Seller harmless from any claim related to the item of equipment purchased. Under no circumstances will the Seller be liable for any damages or expenses by reason of use or sale of any such equipment. The Seller assumes no liability regarding the improper installation or misapplication of its products. It is the installer’s responsibility to check for proper installation and if in doubt, contact the manufacturer. The Buyer is solely responsible for all warranty issues from the manufacturer.

LIMITATION OF WARRANTY

The Seller gives Limited Warranty as to description, quality, merchantability, and fitness for a particular purpose, productiveness, or any other matter of Seller’s product sold herewith. The Seller shall not be responsible for the products proper use and service and the Buyer hereby waives all rights other than those expressly written herein. This warranty shall not be extended, altered or varied except by a written instrument signed by Seller and Buyer.
Limited lifetime warranty on all PPE cast aluminum products, and PPE Transmission Coolers. Three (3) year limited warranty on PPE Manifolds and Up- Pipes Kits, and OEM-Length Up-Pipes. One (1) year limited warranty on all other PPE products from the date of sale to original buyer and limited solely to the parts contained within the products kit. All products that are in question of Warranty must be returned prepaid to the Seller and must be accompanied by a dated proof of purchase receipt. All Warranty claims are subject to approval by Seller. Under no circumstances will the Seller be liable for any labor charged or travel time incurred in diagnosis for defects, removal, or re-installation – of this product or any other contingent expenses. Under no circumstances will the Seller be liable for any damage or expenses incurred by reason of the use or sale of any such equipment. In the event that the buyer does not agree with this agreement: the buyer may promptly return this product, in a new and unused condition in its original packaging, with a dated proof of purchase to the place of purchase within ten (10) days from date of purchase for a full refund. The installation of this product indicates that the buyer has read and understands this agreement and accepts its terms and conditions.

PPEpower.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals