Oneida-Air AHR000025-KIT Hose Reel and Hose Instructions

June 14, 2024
Oneida-Air

Oneida-Air AHR000025-KIT Hose Reel and Hose Instructions
Oneida-Air AHR000025-KIT Hose Reel and Hose

System Contents

If you cannot find an item on the list examine the packaging materials very carefully. *Certain components are pre-installed for ease of installation.

ID Part number Part description Qty
A* AHP000005 Body Assembly 1
A1* AAC810025 Core 1
A2* AHM000025 Wall Mount Plate 1
A3* AHS000025 Handle Side Assembly 1
A4* AHS000251 Outlet & Brake Side Assembly 1
B AHH500513 Handle 1
C AFW000007 2″ Nylon Spacer 1
D AFS000009 1/4″-20 X 3″ Button Head Screw 1
E DFH000025 2.5″ Outlet Coupler 1
F AFS000011 8-32 x 3/8” Button Head Screw 3
G ACT000238 Brake 1
G1 AFT000011 1/4″-20 Hex Nut 2
H AFW000008 2″ Nylon Spacer 1
I AFS000010 1/4″-20 X 3″ Button Head Screw 1
F AFS000011 8-32 x 3/8″ Button Head Screw 4
J ACL000003 3″ Loop Clamp 1
K AFS000004 #10 x 1/2” Self-Drilling Screw 1
L VSHRFB250 2.50″ X 25′ Hose 1
M ACB360000 Turn Key Hose Clamp 2
N ZBT000003 Template 1

*Extra components are included with the brake that are not needed for install.

You will need the following tools:

WALL MOUNTING BRACKET

Stud Finder| Light Adhesive Tape| Allen Wrench| Power Drill
Tack / Center Punch / Nail| Tape Measure / Ruler| Flathead Screwdriver| Drill Bit (for your wall fastener)
Wall Mounting Fasteners *| Level Tool| Pencil / Marker|

You will need to supply your own wall mounting hardware. Use appropriate fasteners for the wall type you are installing your system onto (e.g. lag bolts, drywall anchors, etc.). Maximum Fastener Diameter: 3/8″. Maximum Washer Outside Diameter: 5/8″.

Package Content

Package Content

Assembly Instructions

  1. Thread the 1/4″-20 X 3″ Screw (D) through the Spacer (H), Brake (G) and both 1/4″-20 Hex Nuts (G1) as shown in [FIG. 1].
    Assembly Instructions

  2. Secure the Brake Assembly (G) to the Outlet & Brake Side Assembly (A4) using four 8-32 x 3/8″ Screw (F) as shown in [FIG. 2].
    Assembly Instructions

  3. Secure the Outlet Coupler (E) to the Outlet & Brake Side Assembly (A4) using three 8-32 x 3/8″ Screws (F) as shown in [FIG. 3].
    Assembly Instructions

  4. Thread the Screw (D) through the Handle Side Assembly (A3), Spacer (C) and Handle (B) [FIG. 4].
    Assembly Instructions

  5. Identify where you will install the Hose Reel in your shop and how the hose reel will be oriented [FIG. 5].
    Assembly Instructions
    The Wall Bracket should be mounted to a sturdy, reinforced wall (e.g. concrete wall, wood-framed wall, etc.) Wall anchors can be used if mounting on drywall. The Included template indicates the proper drill holes and the full, assembled size of the Wall Bracket.

  6. Mark a straight level line. Align the top of the Template (N) with the marked line and temporarily secure the template to the wall with a tack or non-marking tape [FIG. 6a]. Place a mark through the template’s paper at each indicated crosshair (four bi-directional keyway holes), then remove the template from the wall [FIG. 6b].
    Assembly Instructions

    Note: DO NOT FLIP THE TEMPLATE! The dimensions of the template are accurate to either orientation of the Hose Reel.
    The central keyway holes can be used to further secure the bracket if standard 16″ on-center stud spacing is not available.

  7. Using appropriate fasteners for the wall type you are installing your system onto, drill into and install fasteners into the wall at all marked locations.
    a. Maximum Fastener Size: 3/8″ diameter
    b. Maximum Washer Size: 5/8″ outside diameter Place washers onto each fastener and thread the fasteners into all four holes, leaving at least 1/2″ outside of the hole to fit the Hose Reel Assembly [FIG. 7].
    Assembly Instructions

  8. Lift the Hose Reel Assembly up and over the fasteners so that the washer is on the inside of the Hose Reel [FIG 8a].
    Slide the Hose Reel Assembly down so that the fastener is snugly inside the smaller section of each keyhole [FIG 8b].
    Assembly Instructions

  9. Tighten these four fasteners to secure the Hose Reel Assembly to the wall [FIG. 9].

    Note: If installing over drywall, avoid overtightening as it may damage the wall.

  10. Secure the Turn Key Hose Clamp (M) tightly onto one end of the Hose (L) as shown in [FIG. 10].

  11. Partially tighten the Turn Key Hose Clamp (M) onto the Outlet Coupler (E) as shown in [FIG. 11a].
    Feed the clamped end of the Hose (L) through the access hole in the Core (A1) closest to the Handle Side Assembly (A3) [FIG. 11b].
    Then attach the Hose to the Outlet Coupler.
    You can guide the Hose by using the secondary access hole in the Core closest to the Outlet & Brake Side Assembly (A4). Secure in place by firmly tightening the Turn Key Hose Clamp on the Outlet Coupler [FIG 11c].
    Assembly Instructions
    Note: To permanently install the Hose, silicone can be applied to the Hose’s cuff prior to being inserted into the Outlet Coupler.

  12. Secure the Hose (L) to the Handle Side Assembly (A3) with the Self-Drilling Screw (K) and 3″ Loop Clamp (J) as shown in [FIG 12].
    Assembly Instructions
    Note: DO NOT screw into recessed portions of the Core (A1).

  13. Guide the Hose (L) as you wind it around the Core (A1) of the Body Assembly (A) so it is neatly wrapped as shown in [FIG. 13]Assembly Instructions

Thank you for your business!

Regardless of where you purchased your system, if you have any questions or issues with missing / damaged parts, please call Oneida Air Systems first to let us help resolve your problem.
We fully stand behind the quality of our product and place the utmost value on our customer’s satisfaction.

We want to do everything possible to make your purchase and experience with Oneida Air Systems a good one!

Customer Service Dept.

1-866-387-8822
support@oneida-air.com

1001 West Fayette Street, Syracuse, NY 13204 U.S.A.
Copyright © 2023 Oneida Air Systems, Inc.

Oneida-Air logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals