Oneida-Air AXD250099 Lid Separator Dust Deput Instruction Manual

June 14, 2024
Oneida-Air

Oneida LOGO

The Industry Leader in Dust Collection
Dust Deputy Low-Pro™ Lid Separator
DIY / Deluxe
# AXD250099
# AXD259922

AXD250099 Lid Separator Dust Deput

Oneida Air AXD250099 Lid Separator Dust Deput

Patents: www.oneida-air.com/patents
Rev: A 20230501LL
Doc. # ZBM000047
Appearance may vary slightly

System Start-Up Information

Read the Safety Practices, installation and maintenance instructions, and your wet/dry vacuum’s owner’s manual before assembling and using the dusts deputy.

  1. DO NOT use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
  2. DO NOT collect flammable or combustible liquids, gases, or explosive dusts, such as gasoline or other fuels, lighter fluid, cleaners, oil-based paints, natural gas, hydrogen, coal dust, magnesium dust, grain dust, aluminum dust, sugar dust, flour dust or gun powder.
  3. Can be used for collecting non-flammable liquids.
  4. DO NOT use or store near hazardous materials.
  5. DO NOT operate the in areas where explosion risks are high. Areas of high risk include, but are not limited to, areas near pilot lights, open flames, or other ignition sources.
  6. ALWAYS wear a NIOSH approved respirator when emptying dust bins and during operation. Dust created by machinery operations may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each work piece material.
  7. NEVER introduce sparks or sources of ignition.
  8. ENSURE all equipment and connections are electrically grounded.
  9. ONLY operate in locations that has a fire extinguisher available nearby.
  10. ALWAYS dispose of waste in a fire safe area after each use. NEVER leave wood dust in a building or vehicle. Wood dust mixtures are highly flammable and can be explosive.

SOME DUSTS ARE HIGHLY FLAMMABLE OR EXPLOSIVE. LEARN/ KNOW WHAT YOU ARE DEALING WITH. FOLLOW ALL LOCAL, STATE, FEDERAL & NFPA CODES AND GUIDELINES.

System Dimensions

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

Oneida Air AXD250099 Lid Separator Dust Deput - System
Dimensions

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.Oneida Air AXD250099 Lid Separator Dust Deput - System
Dimensions1

System Contents

ID Part number Part description Qty
A SDL250000 Lid Separator 1
B RGZ582599 5/8 x 40″ Gasket 1
C RGZ031640 1/4 x 40″ Gasket 1
D AHX000035 Latch Hardware Pack 2
D1 AFL000009 Latch 1
D2 AFS000012 6-32 x 5/8″ Poem Stud 1
D3 AFC230213 Wire Spring Clip 1
D4 AFW188075 3/4″ Flat Washer 1
D5 AFT000020 6-32 Wing Nut 1
E VFA050015 Metal Grounding Tape 30″

INCLUDED ONLY WITH DELUXE SYSTEMS
F| SDS050002| 5-Gallon, 100-Mil, Plastic Bucket| 1
G| RHB000000| Caster Mounts (4 Pack)| I 1
I-I| AFQ080101| Double Sided Tape| 1
I| RHC158716| Casters (4 Pack)| 1
J| RHS000004| Tether Pack| 1
11| AFS080375| #8 x 3/8 Sheet Metal Screw| 1
J2| AFB148000| D ring with clip| 1
J3| AFC000007| PSA Retainer Clip| 1
J4| AFB100000| Split ring| 1
15| AFH343800| Lanyard| 1
K| AXD200036A| 2″ x 36″ Hose| 1
L| AXD600103A| 2″ Elbow| 2

Oneida Air AXD250099 Lid Separator Dust Deput - System
Dimensions2

Assembly Instructions

you will need the following:

  • Phillips Head Screwdriver
  • Bucket
  • Scissors / Razor Blade
  • Wet/Dry Vacuum
  • Vacuum hose and adapters (2.5″ recommended)
  1. Secure each Poem Stud (D2) to the Lid Separator (A) through the holes as shown in [FIG. 1].Oneida Air AXD250099 Lid Separator Dust Deput - Assembly

  2. Apply the 5/8″ Gasket (B) onto the Lid Separator (A) along the underside rim. [FIG. 2] Apply the 1/4″ Gasket (C) perpendicular to the 5/8″ Gasket along the lip of the Lid Separator. The 1/4″ Gasket will follow the inner diameter of  the 5/8″ Gasket. [FIG. 2] Note: The Gasket should overlap around the circumference, firmly pressing against itself to avoid air leaks. Dust collection systems cannot operate effectively if there isn’t a complete seal. There must be NO air leaks.Oneida Air AXD250099 Lid Separator Dust Deput - Assembly1

  3. Secure each Latch (D1) to the previously installed Poem Stud (D2) on the Lid Separator (A) using one Wire Spring Clip (D3), one Washer (D4), and one Wing Nut (D5) as shown in [FIG. 3].
    Note: Refer to Optional Grounding Instructions prior to installing the Latch Hardware Pack (D) if necessary.Oneida Air AXD250099 Lid Separator Dust
Deput - Assembly2

  4. If you did not purchase the Deluxe Unit, proceed to Step 9.
    Insert the Casters (I) into the Caster Mounts (G). Apply pressure and twisting motion until Wheels snap into place [FIG. 4].Oneida Air AXD250099 Lid
Separator Dust Deput - Assembly3

  5. Ensure that the surfaces on the Bucket (F) and Caster Mounts (G) are clean and dry. Remove a square from the Double Sided Tape (H) and apply to the Caster Mount in the recessed location at each corner [FIG 5].

  6. Flip the Bucket (F) upside down and arrange the Caster assemblies evenly around the bottom edge [FIG. 6].
    Note: We recommend arranging the Caster Assemblies at 90° increments from each other for the most stable setup.Oneida Air AXD250099 Lid Separator Dust
Deput - Assembly5

  7. The Caster assemblies must be adhered to the Bucket (F) with a single smooth motion so that the bottom edge of the Bucket fits within the recessed channel of the Caster Mount [FIG. 7a].
    Remove the backing paper from the Double Sided Tape (H) on the Caster assembly. Rest the lip of the Caster assembly against the bottom of the Bucket and then rotate the Caster assemblies flush against the side of the Bucket. Press firmly for a secure fit [FIG. 7b].
    Note: Optional step to more securely attach the Caster Mounts to the Bucket we recommend a ¼”-20 nut and ¼”-20 x 1/2″ bolt (not included).Oneida
Air AXD250099 Lid Separator Dust Deput - Assembly6

  8. The Dust Deputy Low Pro Deluxe can be attached to your wet/dry vacuum to move as one unit. The Tether Pack (J) includes a variety of components to meet the needs of any make/model vacuum. Examine your vacuum  configuration first to review what option works best. You are not limited to the below options:
    a. Attach the Split Ring (J4) to the slot on the Caster Mount (G) and attach the Retainer Clip (J3) onto your vacuum’s foot caster. Then loop the Lanyard (J5) around your vacuum’s foot caster and through itself and the Retainer Clip.  Finally, clip the Lanyard to the Split Ring. [FIG 8a] b. Attach the D ring (J2) to the vacuum with the Sheet Metal Screw. (J1) Then loop the Lanyard (J5) around the slot on the Caster Mount and through itself. Finally, clip the Lanyard to the D ring [FIG 8b] [FIG 8c].Oneida Air AXD250099 Lid Separator
Dust Deput - Assembly7Oneida Air
AXD250099 Lid Separator Dust Deput - System Dimensions3

  9. Snap the Low-Pro assembly onto your bucket – either (F) or your own – and ensure that the Latches (D1) are fully seated with the lip of your bucket [FIG. 9]. The Wing Nut (D5) can be loosened to slide the Latch tighter to the  bucket lip.
    Note: It’s normal for the Low-Pro to fit loosely but it will seal firmly shut under vacuum pressure. To empty your bucket, lift up on the latches and pull up on the Low-Pro.

  10. If you purchased the Deluxe Unit, connect the Low-Pro’s (A) top outlet port to your vacuum with Hose (K) and both Elbows (L) as shown in [FIG. 10a].
    If you purchased the DIY Unit, connect the Low-Pro’s top outlet port to your vacuum with your hose [FIG 10b].
    Connect the Low-Pro’s side inlet port to your tool with your vacuum’s hose [FIG. 10a] [FIG. 10b].
    Note: Both ports accept standard 2.5″ hose cuffs (OD ≈ 2.25″).Oneida
Air AXD250099 Lid Separator Dust Deput - System
Dimensions5

  11. Make sure there are no air leaks at the connections. Review [FIG. 11] for common leak points.
    Note: Any air leak will affect separation performance. Make sure to check your dust drum frequently so you do not overfill it. One option to check for air leaks is with a smoke test. Test kits are found at most hardware stores in the  HVAC section. Introduce smoke around every leak point. If you see the smoke being drawn into the system, you’ve found an air leak that needs to be sealed.Oneida Air AXD250099 Lid Separator Dust Deput - System
Dimensions6

Optional Grounding Instructions

Recommended for fine dust situations or electronically sensitive applications.

  1. Install the Metal Tape (K) to the Lid Separator (A) so that the inlet, outlet, and flange are attached by a continuous, conductive path. The tape should wrap 1/4″ around the edge of each opening [FIG 12].Oneida Air AXD250099 Lid Separator Dust Deput - Grounding
  2. For added grounding, attach a self-supplied wire with a ring terminal on one end and a washer tied to the other end when installing one of the latches in step 3. The wire must be long enough for the washer to lie on the floor [FIG  13].Oneida Air AXD250099 Lid Separator Dust Deput - Grounding 1

Troubleshooting

Problem caused Solution

Not separating well.
(Only a tiny amount of dust
should reach the vacuum)| Air leaks in the bucket| 1. Check for leaks between the Low-Pro Lid Separator and the bucket.
2. Check for holes or leaks in the bucket.
Material not dropping
into the dust container.| Collecting large,
bulky material| 1. Large, bulkier material might swirl. Restart or temporarily cut off
airflow to drop material down.
Low air volume| System clogged| 1. Clean vacuum and the vacuum filter per the manufacturer’s specs.
2. Check all hose connections for a blockage in the hose.
Drum collapsing| Blocked airflow| 1. Ensure the end of the hose isn’t blocked.
Hose pulling off| Hose connections not tight| 1. Due to the varied hose diameters, flexible couplers can be used.
They are available at local hardware stores in the plumbing section.
2. Use a hose clamp.
3. Wrap the inlet and outlet of the Low-Pro with a layer of electrical tape to increase the friction fit.
4. Secure hose with a sheet metal screw.

Accessories

2.5″ x 4.5′ wire Reinforced vacuum hose

AXD250054

• Crush-resistant, flexible hose with a smooth wall inner lining that minimizes air resistance.

1.25″ x 1.5″ hose adapter kit

AKD000000

• Includes reducers, adapters, and O-rings for connecting smaller vacuum hoses to standard Dust Deputy ports.

2.5 tapered Static conductive vacuum hose elbow

AXD600103

  • For creating smooth 90 degree hose turns with minimal loss of air performance. Tapered on one end for easy friction-fit hose connections.

2.5″ vacuum hose coupler

AXD225225

  • Used for connecting separate lengths of 2.5″ vacuum hose.
  • Slips over 2.25″ O.D. hose cuffs and features a inner beaded section to complete the friction fitting.

2″ vacuum hose coupler

VSHNZZ200

  • Efficiently couple together long lengths of flexible vacuum hose with a secure friction fit.
  • Made from steel for rigidity, durability, and static grounding.

viper vacuum Scraper Paint Removal tool

AXS001160B

  • Ergonomic hand scraping tool with hightextured grip and reversible, tungsten-carbide blade.
  • Hollow handle fits 1-1/4″ to 1-1/2″ vacuum hoses.

universal dust-free Router hood

AXH000001

  • Collects router waste from both above and below the bit, virtually eliminating postproject cleanup.

1.5″ x 6.5′ dust extraction hose whip

AHE000001

  • This highly flexible vacuum hose fits onto the dust collection ports of common portable power tools. Includes 2.5″ rotating swivel cuff.

Warranty Information

limited warranty – activate online at oneida-air.com/warranty
Oneida Air Systems, Inc. (Oneida Air Systems) warrants the Dust Deputy for a period of 1 year, to the original purchaser from the date of purchase, unless otherwise specified. Items not manufactured by Oneida Air Systems are limited to  their own manufacturer’s warranties. All electrical items such as magnetic starters, remotes, sensors, pumps, bin sensors, bag grippers, etc. and accessories are limited to 90 days. Oneida Air Systems warrants that the product will be free  from defects in materials and workmanship.
This is Oneida Air Systems’ sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty.  Oneida Air Systems does not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. This warranty does not apply to defects due directly or indirectly to misuse,  negligence, accidents, abuse, repairs, alterations, improper wiring or lack of maintenance. In no event shall Oneida Air Systems’ liability under this warranty exceed the purchase price paid for the product and any legal actions brought  against Oneida Air Systems shall be tried in the State of New York, County of Onondaga.
The buyer is cautioned to install and operate dust collectors in accordance with prescribed federal, state, OSHA, NFPA, local codes and regulations. This equipment should be installed/wired by a licensed electrician following all applicable codes. Local codes can be significantly different from national codes. The customer assumes the responsibility for contacting their insurance underwriter with regard to specific application requirements of venting or if additional fire protection and safety equipment may be required. Oneida Air Systems shall in no event be liable for death, injuries to persons or property, or for incidental, and contingent, special, or consequential damages arising from the use of our product.
Oneida Air Systems makes every effort to accurately represent our products and prices, however Oneida Air Systems reserves the right to make changes to products and prices at any time. As a manufacturer, Oneida Air Systems reserves  the right to change product specifications at any time in an effort to achieve better quality products.
ONEIDA AIR SYSTEMS SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, AND CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCT.
SAFETY WARNING – PLEASE READ

Before purchasing or installing a dust collection system, the buyer is cautioned to do so in accordance with prescribed federal, state, local, OSHA, NFPA, and any other applicable codes or regulations relating to the type of dust(s) you are collecting.
SOME TYPES OF DUST UNDER CERTAIN CONDITIONS HAVE THE POTENTIAL TO BE EXPLOSIVE.
Oneida Air Systems is not responsible for how the dust collector is used or installed. Dusts with deflagration or explosion risks, such as wood dust, may require additional safety equipment, including but not limited to; venting, spark  detection, suppression systems, backdraft dampers or may require installation in an outside location or in a protected area away from personnel. The customer assumes the responsibility for contacting their insurance underwriter with  regard to specific engineering controls or application requirements.
We suggest you reference NFPA 664, 654 and 68 codes for more information. Oneida Air dust collection systems may not be suitable for some applications and are not designed to be used in explosive atmospheres. Oneida Air Systems equipment should only be installed and wired by a licensed electrician following all applicable local and national electrical codes.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead- based paints; crystalline silica from bricks, cement and other masonry products; arsenic and chromium from chemically-treated lumber; etc. Your risk from these exposures varies, depending on how often you do this type of work. To  reduce your exposure to these chemicals, work in a well ventilated area, and with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. Oneida Air Systems recommends using  additional approved safety equipment such as an approved OSHA and NIOSH dust mask or respirator.

Oneida LOGO The Industry Leader in Dust Collection

Thank you for your purchase of this American made product!
Regardless of where you purchased your Oneida Air Systems’ product, if you have any questions or issues with missing / damaged parts, please call us first to let us help resolve your problem. We fully stand behind the quality of our  products and place the utmost value on the satisfaction of our customers. We want to do everything possible to make your purchase and experience with Oneida Air Systems a good one!

Customer Service Department
1-866-387-8822support@oneida- air.com
1001 West Fayette Street, Syracuse, NY 13204 U.S.A.
Copyright © 2023 Oneida Air Systems, Inc.

Documents / Resources

| Oneida-Air AXD250099 Lid Separator Dust Deput [pdf] Instruction Manual
AXD250099 Lid Separator Dust Deput, AXD250099, Lid Separator Dust Deput, Separator Dust Deput, Dust Deput, Deput
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals