Jovoko MP5 7.0 Inch TFT LCD Receiver Instruction Manual

Jovoko MP5 7.0 Inch TFT LCD Receiver

Product Information

Specifications

• Power Supply Voltage: 12 V DC, Negative Ground
• Max Current Consumption: 15 A
• Max Output Power: 4x55W

Product Usage Instructions

Installation

1. Remove the stereo carefully from the box, keeping the box for warranty and service purposes.
2. Remove the screws.
3. Unpack the car’s dashboard and mounting bracket.
4. Check the size of the board window to meet the requirements.
5. Align the holes of the left alignment screws and the right plates.
6. Fix the machine support with screws in the dashboard.
7. Install the control panel.

Precautions
Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver. Avoid installing the unit where it would be subject to high temperatures, direct sunlight or hot air from the heater, dust, dirt, or excessive vibration. Use only the supplied mounting hardware for a safe and secure installation. Adjust the mounting angle as desired.

Note:
Keep the release Key in a safe place as you may need it in the future to remove the unit from the car.

Wiring Diagram

WARNING:
Use the specified amperage fuse for each lead. Using a higher amperage fuse may cause serious damage.

Power Cables Wiring:

• Black 1 – Ground
• Black 2 – Ground
• Red – 12V positive Ignition Switch ACC
• Yellow – 12V Battery positive
• Blue+Black – Steering wheel Control line
• Orange – Small Light Line
• Brown 1 – Steering Wheel Control Line
• Blue – Power Antenna/Amplifier Turn on
• Pink – Backing Line
• Brown 2 – Steering Wheel Control Line

Speaker Cables Wiring:
There are four groups of speaker cables: green, grey, white, and purple. Each color represents one group, and one group connects to one speaker’s positive wire and negative wire.

Camera Wiring:

1. Power cable:
   • Red – Reverse light positive
   • Black – Reverse light negative
2. RCA cable: Connect the yellow port to the CAMIN port (yellow) on the radio.
3. Make sure the pink cable on the radio power cable is connected to the backing line. This will enable the device to show the rear view image automatically when parking and return to the radio page when parking finishes.

FAQs

Language Setting:
To set the language, go to Settings > Language.

Why can’t watch the video, showing a ‘video warning’?
To disable the video warning, go to Settings > Other > Video Warning and turn it off.

Why can’t use GPS?
If you are unable to use GPS, try re-activating the SD map card by following these steps:

1. Remove the SD card, make sure there is no dust on it, and put it back in the unit.
2. Click Navigation/GPS > Setup > Navi Path > Primo > Primo.exe > Load Map Automatically.
3. Return to the home page and click Navigation to load the map and start using it.

SAFETY PRECAUTIONS

INSTALLATION
Please read the following notice before the installation

1. Make sure that you or the professional are using our original connector in your first installation, otherwise, it could cause a short circus in the radio because the order of the cable does not match correctly. If you use another connector, the radio may not turn on or make any sound, even when you use our original connector for the second attempt. Any damage caused by misuse of the wiring will not be included in the terms of the warranty.
2. After installing the radio, you may see some regular problems that most buyers can see, but most of which can be verified and resolved by “F&Q”

Remove the stereo carefully from the box. keeping the box. For warranty and service of the unit.

1. Remove the screws.
2. Unpack the car’s dashboard and mounting bracket.
3. Check the size of the board window to meet the requirements. The holes of the left alignment screws and the right plates.
4. By machine, support is fixed with screws in the dashboard.
5. Control panel installed.

PRECAUTIONS

• Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver.
• Avoid installing the unit where it would be subject to high temperatures, from direct sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration.
• Use only the supplied mounting hardware for a safe and secure installation.
• Adjust the mounting angle as desired.
• Note: Keep the release Key in a safe place as you may need it in the future to remove the unit from the car.

Key display

WIRING DIAGRAM

WARNING
Use the specified amperage fuse for each lead. Using a higher amperage fuse may cause serious damage.

Power Cables Wiring:

• Black 1 — Ground
• Black 2 — Ground
• Red — 12V positive Ignition Switch （ACC）
• Yellow — 12V Battery positive
• Blue+Black– Steering wheel Control line
• Orange — Small Light Line
• Brown 1– Steering Wheel Control Line
• Blue — Power Antenna/Amplifier Turn on
• Pink — Backing Line
• Brown 2 — Steering Wheel Control Line

Speaker Cables Wiring:
There are four groups of speaker cables, green, grey, white, and purple. Each color is one group, and one group connects to one speaker’s positive wire and negative wire.

Camera Wiring:

1. Power cable: red and black
   • Red — reverse light positive
   • Black — reverse light negative
2. RCA cable: yellow port. insert into CAMIN port (yellow) on the radio
3. Make sure the pink cable on the radio power cable is connected to the backing line.

Thus, the device will show rear view image automatically when you are parking, and return to the radio page when parking finishes.

Installation Guide

SPECIFICATIONS

FM TUNER

• Frequency Range 87.5-108MHz
• Sensitivity 10 dBu
• I.F. Frequency 10.7MHz
• Frequency Response 80Hz-12kHz (±3dB)
• Stereo Separation >25dB
• S/N Ratio >50dB

GENERAL

• Power Supply Voltage 12 V DC, Negative Ground
• Max Current Consumption 15 A
• Max Output Power 4x55W

Note:
Specifications and the design are subject to possible modification without notice due to improvement.

F &Q:

1. Language Setting: Setting- Language

2. Why can’t watch the video, showing a ‘video warning’?
   Please click ‘Setting – other – video warning’ and turn ‘video warning’ off.

3. Why can’t use GPS?
   Please try to re-activate the SD map card.
   Steps:

4. Remove the SD card, make sure there is no dust on it, and put it back in the unit

5. Click “Navigation/GPS – Setup – Navi Path” – “Primo” – “Primo.exe” – “Load Map Automatically” – “.

6. Return to the home page and click “Navigation” to load the map, and start to use it.

7. If the map is still empty, click on the map to show the “+” and “-” buttons, and click “+” to magnify the map until it shows streets

8. Why does the car radio show “No Signal” when I’m reversing?
   If the camera can light up when it connects to power, the camera can work. Then please check if the camera’s lines are wired correctly, exactly as written in “camera wiring”.

Main Functions

HOME
In the taskbar click to enter the main menu interface.

1. Click here to enter the radio player interface.
2. Click here to enter the music player interface.
3. Click here to enter the video player interface.
4. Click here to go to the photo browsing interface.
5. Click to go to the A V IN interface.
6. Click to go to the aux input interface.
7. Click here to go to the Bluetooth player interface.
8. Click to go to the GPS interface.
9. Click to go to the previous/next page.
10. Click here to adjust the screen brightness and off-screen.
11. Click to go to the System Settings interface.

MUSIC
In the main menu interface, touch the MUSIC icon to enter the music state.

Features taskbar icon

1. Click here to enter the menu setting.
2. The volume regulation, and paddling can adjust the volume.
3. Return
4. Enter the main menu
5. Click here to play the previous/next song.
6. Click here to play/pause.
7. Click here to Shuffle.
8. Click here loop.
9. Playback progress display.

PHOTO
In the main menu interface, touch the PHOTO icon to enter the photo state.

1. Click here to play the prev/next picture.
2. Click here to play/pause.
3. Click here to zoom in.
4. Click here to zoom out.
5. Click here to rotate the image.

VIDEO
In the main menu interface, touch VIDEO icon to enter the video state.

1. Click here to play the previous/next video.
2. Click here to play/ pause.
3. Click here loop.
4. Click here to Shuffle.
5. Playback progress display, Touch paddling can fast forward and rewind.
6. Next page

RADIO
In the main menu interface, touch the RADIO icon to enter the radio state.

1. Click here to manually scan the radio.
2. In the radio state, each band has six frequency points, press any frequency, and you can store your favorite radio stations.
3. LOC/DX Switch
4. Stereo
5. Press to automatically search for radio stations and store the FM 1- FM2- FM3 18 radio stations, and short press to navigate through the radio.
6. Band Switch

BT
In the main menu interface, touch the BT icon to enter the Bluetooth state.

Click on the dial-up interface.

1. Bluetooth dial number keys can be used to enter a phone number to dial.
2. Backspace
3. Bluetooth is available under the call state will host the button to switch\ the sound to the phone.
4. hang up the phone.
5. Dial/answer a call.

Click to go to the call log interface

1. Missed record, received record dial record list.
2. Received record
3. Dial record
4. Missed record

Click on the contact interface

Click to go to the Bluetooth music interface

1. Prev/Next, play/pause function.

SETUP

In the main menu interface, touch the SETUP icon to enter the setup state.

1. Click on sound settings.
2. Click on the language Setup.
3. Other settings.
4. Click to go to the radio region selection.
5. Click on the steering wheel control settings.
6. Click to set the time.

Touch the Radio Area, and select the radio region

Touch TIME, into the time setting

1. Touch to set the time and date
2. 12/24 standard switch

Touch Wheel Control, Steering wheel control interface

Enter the learning state:

1. Long press the button on the steering wheel using your left hand, then touch the screen corresponding function using your right hand, make it highlight, mean learn OK;
2. When the learning is completed, click Confirm.
3. When learning has failed, it should not respond to the steering wheel.
4. If an operating mistake in the learning process, click Reset to relearn.

Other settings interface

1. Software Update
2. Factory Data Reset
3. Calibration
4. Background Set

Touch Language, select the national language

CPS NAVIGATION

CPS NAVIGATION (Optional)
In the main menu interface, touch the GPS icon to enter the Navigation.

AUX IN

In the main menu interface, touch the aux-in icon to enter the aux-in state.

Front panel 3.5mm audio input.

AV IN
In the main menu interface, touch the av in icon to enter the av in the state.

RCA audio/video input.

INSTALLATION

PRECAUTIONS

• Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver.
• Avoid installing the unit where it would be subject to high temperatures, from direct sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration.
• Use only the supplied mounting hardware for a safe and secure installation.
• Adjust the mounting angle as desired.

MOUNTING EXAMPLE

Installation In the dashboard

Note:
Keep the release Key in a safe place as you may need it future to remove the unit from the car.

WARNING
Use the specified amperage fuse for each lead. Using a higher amperage fuse may cause serious damage.

FEATURES

The Unit Features MP5/USB/SD Ports and 7.0 inch TFT LCD

• Electronic PIl Tuning Control with 18 Programmable Stations
• MP3/WMA Compatible
• Preamplified Line-out
• Front Audio Aux-in
• USB Port and SD/MMC Input
• Last Track Memory (RADIO & SD/MMC & USB)
• 7.0 inch TFT LCD

Note:
Specifications and the design are subject to possible modification without notice due to improvement.

REMOTE CONTROL GUIDE

1. Power/Mute
2. SRC & End Call
3. Play/Pause
4. Band (switch for FMI-FM2-FM3) & Answer Call
5. Prev
6. Next
7. AMS
8. Vol-
9. Vol+
10. Audio & NO.0
11. A.V.P.
12. System Menu
13. NO.1
14. NO.2
15. NO.3
16. NO.4
17. NO.5
18. NO.6
19. NO.7 &RPT
20. NO.8 & INT
21. NO.9 & SUB-T

LOCATION OF CONTROL

1. PWR: Power ON/OFF
2. MODE: Function Selector (radio/usb/sd/aux-in/bt) & End Call
3. AMS: Auto Seek Search Tuning
4. BAND: Band Bullon (FM 1-FM2-FM3) & Answer Call
5. /6. : Short press: Prev/Next, Long press:Fast forward/rewind; Manual Auto Search Radio
6. SD: Micro SD Card Slot, GPS navigation map card slot (optional model)
7. AUX IN: AUX IN Jack
8. USB: USB Port
9. LCD: LCD Display
10. VOL/SEL: Volume / Select Control
11. MUTE: Mute ON/OFF
12. DISP: Clock Display
13. EQ: flat-pop-classic-rock/ NA VI: Enter the navigation interface (optional model)
14. :Return to the previous level

SUPPORT VIDEO FORMAT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>