Sopito V6 Chip Cutter Machine User Manual
- June 14, 2024
- Sopito
Table of Contents
Sopito V6 Chip Cutter Machine
Graphics and drawings in this manual are solely for illustration purposes and are subject to variations from actual product. Read all instructions before using this appliance for the first time. Keep this manual for future reference.
GENERAL SAFETY RULES
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
- Keep the appliance out of reach of children. Children should be supervised to ensure that they do not play with the appliance.
- Do not use or place the appliance near edge of the table or counter. Always place the appliance on a flat, level and dry surface.
- The blades and components are very sharp. Care shall be taken when changing accessories, after use and during cleaning and maintenance. It is suggested that you wear cut-resistant gloves when handling the cutting plates.
- Never touch the blades or inserts with your hand. Keep fingers clear of cutting blades at all times.
- Never use accessories or parts made by other manufacturers not recommended or sold by Morgles as it may cause a risk of injury to persons.
- Do not use the appliance for other purpose than its intended use.
COMPONENT LIST
- Cutting Plate
- Guide Shaft
- Pushing Plate
- ALu Pushing Plate base
- Lever
- Lever arm
- Butterfly nut
- Clip
- Safety plate
- Bolt
- Suction feet
Installation
- Unbox, take out the following parts:
- Main body
- Lever
- Lever arm
- Cutting plate
- Pushing Plate
-
Using screws to tighten 2 and 3, prepare for next step.
-
Put the lever in slot in the compartment, insert bolt, screw to tighten it. Attention, add a clip before insert a bolt.
-
Pull the pushing plate base back to bottom most, please make sure the holes of the pushing plate base and lever arm are in the right position, and a clip and insert bolt.
CHANGING THE PUSHING PLATE AND CUTTING PLATE
Caution : Pushing plate and cutting plate is a set, please use the same spec. 9x9mm or 12x12mm, otherwise the machine would be damaged. KEEP FINGERS CLEAR OF CUTTING BLADES AT ALL TIMES. Never hold the product with your hands in line of the cutting blade.
Step 1: Pull the lever to aftermost position to make compartment fully open.
Step 2: Rotate the metal clip counter clockwise to release the pushing plate, take out the pushing plate to replace it with new one.
Step 3: Unscrew the 4 butterfly nuts to release the cutting plate.
Attention: Never hold the product with your hands in line of the cutting
blade. It is suggested that you wear cut-resistant gloves when handling the
cutting plates.
Step 4: Choose the intended pushing plate and cutting plate set, follow
the instruction in the below left drawing, remove bolts ① & ②, then remove ③
the lever, set the cutter upright to prevent the safety plate from moving,
install the cutting plate as shown in the below right drawing, don’t forget to
put clip in the picture A, the side with foams of cutting plate (shown in
below right drawing B) should be facing the same direction as suction cup
(shown in below right drawing C).
CUTTING POTATOES
Step 1 : Place the cutter on a flat work surface, clean work surface A
and section cup B, then suck the cutter to the work surface to make sure no
movement during use.
Step 2: Pull the lever till the compartment is fully opened, put potato in it
- It’s recommended to cut an edge on the end of the potato ② to make it easily to be cut off.
Step 3: Any high fiber food like carrot or sweet potato, it’s recommended to push back the lever a bit then push forward the lever rapidly to make them easily cutt off. This cutter has been tested for 10,000 times, it can be used ti cut potatoes, carrots and sweet potatoes etc.
Step 4: Follow ” Cleaning and Maintenance” section to clean cutting plate, pushing plate and compartment.
Cleaning and Maintenance
It is recommended to thoroughly clean your cutter before and after each use. Clean with hot, soapy water, then rinse with clean water and dry thoroughly. Keep your fingers away from cutting plate, DO NOT take the cutter from the cutting plate side. Caution! Use extreme care when handling the cutting plate and blades. The blades are extremely SHARP! It’s suggested that you wear cut- resistant gloves when handling the cutting plates.
Step 1: You may need to disassemble the pushing plate and cutting plate
according to the instructions in “CHANGING THE PUSHING PLATE AND CUTTING
PLATE” section to clean thoroughly.
Step 2: Use a long bristle brush to remove debris and clean the cutting
plate, DO NOT use your fingers!
Step 3: To clean the pushing plate, remove any remaining debris with a blunt object, such as a butter knife, then thoroughly clean it with a long bristle brush.
WARRANTY INFORMATION
MORGLES WARRANTY INFORMATION
We provide one year warranty for this product, contact manufacturer’s official
site if services is needed under warranty. The warranty covers only the
product and its specific parts, not the food or other products processed in
it. Morgles is not responsible for missing or damaged parts on discounted
clearance, resale or final sale items where the seller may not be able to
guarantee full functionality or completeness of the unit. Morgles will not
accept any liability for possible damage caused by improper or incorrect use.
DISPOSAL
The packaging materials are environmentally friendly and can be recycled.
Please dispose the packaging materials in the appropriate container at the
community waste disposal facilities.
Email : support@morgles.com (We will reply within 24 hours)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>