Srygery BSV-IC005 Solar Drip Irrigation System Instruction Manual

Srygery BSV-IC005 Solar Drip Irrigation System

Product Information

Specifications

• Item Name : Solar Automatic Watering System
• Model No.: BSV-IC005
• Solar Panel : 3W
• Battery : 3.7V/2200mAh
• Pump : 1W
• Max Water Flow : 400mL/min
• Water Sensor : Yes
• Operating Temperature : 33.8-104°F
• Storage Temperature: -50-122°F

Product Usage Instructions

Assembling the Drip Irrigation Kit
Before you start, plan the layout of plants and water tubing to the solar controller.

Important Safeguards

1. Read all instructions carefully.
2. Do not disassemble the product by yourself.
3. Do not vigorously vibrate, beat, or hit the product.
4. Do not throw the product into fire to avoid the risk of fire or explosion.
5. Children should use this product under the guidance of their parents.
6. Avoid using the product when the ambient temperature is higher than 40°C or lower than 0°C.
7. Do not put the product into water. Ensure that the side with the switch button is faced down to prevent water from entering.
8. Use a water filter at the water inlet pipe interface to prevent damage to the main unit.
9. Install the product in a sunny place and regularly clean the dirt on the solar panel to improve charging efficiency.

Using the Drip Irrigation Kit

Package Contents

• Solar Controller
• Manual (1)
• Ground Stake (1)
• Screw (2)
• 65.6 Feet Water Pipe (1)
• Dripper (20)
• Barb Fitting (20)
• Water Pump Filter (1)
• Water Level Sensor (1)
• Anti-siphoning Accessory (1)

Watering Program Table

ON/OFF button – Program Start
MODE button – Program Interval & Volume – Blue LED on Solar Controller

1. Tailor the pipe into the length you need.
2. Connect the T-joint and dripper and insert it into the potting soil.
3. Add the Anti-siphoning accessory to the water outlet.
4. Connect the water filter to the inlet.

Main Line Water Tube

1. Arrange plants at desired positions.
2. Lay Main Line tubing in front of plants.
3. Mark plant positions on Main Line water tube section (tape or bread ties).
4. Cut tubing with scissors at plant location.
5. Insert T-Joints into Main Line water tubing at each plant position.

Lateral Line

1. Arrange short Lateral Lines between Main Line and plants.
2. Install the end of Lateral Line onto Main Line T-Joint.
3. Install Drip-Stake on the other end of Lateral Line.
4. Insert Drip-Stake into the plant.

Note

• There are two ways to install the product.
• Connect the water sensor and place the probe and water filter in the water. Then turn on the machine.

TIP: Hot water can be used to soften the end of the water tube to fit over the T-Joint barb. Lightly soap the end of the selected T-Joint. Dip the tube end in hot water for 10-15 seconds. Dry the tube end and fingers. Use repeated pushing movements to fit the warmed tube end completely over the T-Joint barb.

Troubleshooting

2. Water Filter clogged
3. Pump clogged| Restore water level.
Clean the water filter.
Clean the pump.

Frequently Asked Questions (FAQ)

• Q: What is the operating temperature range of the product?
  • A: The operating temperature range of the product is 33.8-104°F.
• Q: Can children use this product?
  • A: Children should use this product under the guidance of their parents.
• Q: Can the product be submerged in water?
  • A: No, it is forbidden to put the product into water. Ensure that the side with the switch button is faced down to prevent water from entering.

For your safety and continued enjoyment of this product, always read the Instruction Book carefully before using.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following

1. READ ALLINSTRUCTIONS
2. Do not disassemble this product by yourself.
3. Do not vigorously vibrate, beat or hit the product
4. It is strictly forbidden to throw this product into fire to avoid the risk of fire or explosion.
5. Children should use this product under the guidance of their parents.
6. When the ambient temperature is higher than 40″C or lower than 0″C, the product may fail to work, please avoid using it.
7. It is forbidden to put the product into water. And the side with the switch button must be faced down, other wise water may enter.
8. Be sure to use a water filter at the water inlet pipe interface, otherwise the main unit will be at risk of damage.
9. Choose a sunny place to install the product and clean the dirt on the solar panel regularly to help improve the charging efficiency.

CONTENTS OF PACKAGE

SPECIFICATIONS

SOLAR CONTROLLER
The unit is equipped with a signal that indicates the solar controller needs to be charged. When the power of the system is low, the ON/OFF button will flash red. After 30 seconds the red light and the blue LED program light will turn off. At this time the system enters the standby state. Later when exposed to light again and the product gets fully charged the system will automatically return to the working program with the blue LED program light and the system will perform a watering and re-time.

WATER LEVEL SENSOR
The unit is equipped with a sensor that detects the water supply is low or blocked. When the water level is low the system will alarm. The beeper sounds twice a minute and the MODE button will flash GREEN. At night, the RED indicator light will flash without a beep.
The cause of this may be that the water pump or the filter is blocked. Please clean them. You can unclog the pump by injecting some warm water into the pump inlet with a syringe.(the syringe is not included.) It may also be that there is no water in the container. Please add water. Program will resume. After troubleshooting please restart the product, the system will perform a watering and re-time.

Note

1. Solar Controller must be above plant level and facing sun.
2. Solar Controller buttons must face toward the ground when installed.
3. Tube ends must be completely over T-Joint barb.
4. Water Container must be below level of plants.
5. Water Sensor Probe rests at bottom of water container Be certain your plant containers / trays are LARGEENOUGH to contain the programmed volume of water and water spillover will not cause damage to surroundings.
6. It is recommended to install more than 5 drippers, if there are less than 5 drippers, the water flow will be slow, blockage may be detected, and an alarm will appear.
7. The anti-siphon installation position must be higher than the bucket.

HOW TO ASSEMBLE
Before you start – Plan the layout of plants & water tubing to solar controller

1. Tailor the pipe into the length you need
2. Connect the T-joint and dripper and insert it into the potting soil
3. A small accessory, adding it to Water Outlet for Anti-siphoning
4. Connect the water filter to the inlet
5. Two ways installation
6. Connect the water sensor and place the probe and water filter in the water. And turn on the machine

HOW TO USE

1. Solar Controller
2. Water Supply Inlet
3. Water Supply Tube
4. Water Supply Container
5. Water Supply Filter
6. Water Level Sensor
7. Probe Connector
8. Probe Sensors
9. Water Supply Outlet
10. Water Mainline
11. T-joints Lateral Tube
12. Drip-Stake 8 Anti-siphon

MAIN LINE WATER TUBE .

1. Arrange plants at desired positions.
2. Lay Main Line tubing in front of plants
3. Mark plant positions on Main Line water tube section (tape or bread ties)
4. Cut tubing with scissors at plant location
5. Insert*T-Joints into Main Line water tubing at each plant position.

LATERAL LINE .

1. Arrange short Lateral Lines between water Main Line and plants.
2. Install end of Lateral Line onto Main Line T-Joint .
3. Install Drip-Stake in other end of Lateral Line.
4. Insert Drip-Stake into plant

Note

1. TIP*- Hot water will soften end of water tube enough to fit over T-Joint barb and tighten as it cools. Lightly soap end of selected T-Joint
2. Dip tube end in hot water 10-15 seconds. Dry tube end and fingers. Use repeated pushing movements to fit warmed use end completely over T-Joint barb.

WATERING PROGRAM TABLE

• ON/OFF button – Program Start
• MODE button – Program Interval & Volume – Blue
• LED on Solar Controller

Water Volume dispensed is 600 ml / minute. Water pumps evenly to each Drip- Stake: Example = 12 Liters to 20 Drip-Stakes = 600 ml water dispensed Unit is equipped with enough water tubing & Drip Stakes to water up to 30 plants. Reduce number of Lateral Lines & Drip-Stakes to dispense more water to each plant – see table Increase number of Lateral Lines and Drip-Stakes to dispense less water to each plant- see table

TROUBL SHOOTING

1. Double Beep every minute until water level restored.
2. Program Timer resumes after restoring water.

| |

1. Water level Low
2. Water Filter dogged
3. Pump clogged

|

1. Add Water to Water Supply Container.
2. Clean Water Filter
3. Inject some warm water into the pump inlet with a syringe.
4. Restart system if needed

Beeping| Green LED flashing| Drip stake clogged.| Clean drip-stake
Red LED flashing| Insufficient solar charge| After sunlight charging. Solar Controller returns to programmed MODE
Siphon effect| |

1. The position of the bucket is higher than the installation height of the product.
2. The watering place is too low.

|

1. Install anti-siphon device.
2. The anti-siphon installation position must be higher than the bucket.
3. The watering place should not be too low.

There is a blockage alarm| | The number of dripper installations is less than 5| More than 5 installations
Solar dripper irrigation kit not working| |

1. The water inlet and outlet are reversed.
2. The solar panel is out of power.
3. The machine is not turned on.

|

1. The water inlet and outlet cannot be reversed.
2. Confirm whether the solar panel is powered.
3. After turning on the machine, you can hear the sound of vibration, indicating that it has been turned on.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>