KitchenAid KMBP107EBS Built In Microwave Oven Instruction Manual
- June 14, 2024
- KitchenAid
Table of Contents
INSTALLATION INSTRUCTIONS ELECTRIC
BUILT‑IN MICROWAVE OVEN SPACER KIT
KMBP107EBS Built In Microwave Oven
| Built-In Spacer Kit | Size and Color | UL Listed for Model Numbers |
|---|---|---|
| W10469901 | 27″ (68.6 cm), stainless steel | KMBP107ESS |
| W10842584 | 27″ (68.6 cm), limited edition black | KMBP107EBS |
| W10469903 | 30″ (76.2 cm), stainless steel | KMBP100ESS |
| W10842586 | 30″ (76.2 cm), limited edition black | KMBP100EBS |
BUILT‑IN MICROWAVE OVEN SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your
appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and
others.
All safety messages will follow the safety alert symbol and either the word
“DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don’t immediately follow
instructions.
You can be killed or seriously injured if you don’t follow instructions.
All safety messages will tell you what the potential hazard is, tell you how
to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed here.
Tools needed
- Phillips screwdriver
- Level
- ¼” (6.3 mm) hex opening screwdriver
- Drill
- ¹⁄8″ (3.2 mm) drill bit
- Measuring tape
Parts supplied
A. Spacer bars (2)
B. Bottom vent (1)
C. ³⁄8″ hex washer head screws (4)
D. ¾” pan head screws (4)
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
- Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance with microwave oven.
- Recessed installation area must provide complete enclosure around the recessed portion of the microwave oven.
- Microwave oven support surface must be solid, level, and flush with bottom of cabinet cutout. Floor must be able to support a weight of 90 lbs (41.0 kg).
IMPORTANT: To avoid damage to your cabinets, check with your builder or
cabinet supplier to make sure that the materials used will not discolor,
delaminate, or sustain other damage. This oven has been designed in accordance
with the requirements of UL and CSA International and complies with the
maximum allowable wood cabinet temperatures of 194°F (90°C).
Product Dimensions
27″ (68.6 cm) and 30″ (76.2 cm) Microwave Oven Spacer Kits 27″ (68.6 cm)
models A. 26³⁄4″ (67.9 cm) overall width
30″ (76.2 cm) models A. 29³⁄4″ (75.6 cm) overall width
Cabinet Dimensions
27″ (68.6 cm) and 30″ (76.2 cm) Microwave Oven Spacer Kits
27″ (68.6 cm) models
A. 27″ (68.6 cm) min. cabinet width
B. 207 ⁄16″ (51.9 cm) bottom of cutout to bottom of upper cabinet door
C. 40″ (101.2 cm) bottom of cutout to floor (recommended)
D. 25¹⁄2″ (64.8 cm) cutout width
E. 1¹⁄2″ (3.8 cm) min. bottom of cutout to top of cabinet door
F. 19 7 ⁄16″ (49.4 cm) recommended cutout height (will fit cutout height from
19¼” [48.9 cm] to 19¹¹⁄16″ [50.0 cm])
G. 217 ⁄8″ (55.5 cm) min. cutout depth| 30″ (76.2 cm) models
A. 30″ (76.2 cm) min. cabinet width
B. 20 7 ⁄16″ (51.9 cm) bottom of cutout to bottom of upper cabinet door
C. 40″ (101.2 cm) bottom of cutout to floor (recommended)
D. 28¹⁄2″ (72.4 cm) cutout width
E. 1¹⁄2″ (3.8 cm) min. bottom of cutout to top of cabinet door
F. 197 ⁄16″ (49.4 cm) recommended cutout height (will fit cutout height from
19¼” [48.9 cm] to 19¹¹⁄16″ [50.0 cm])
G. 21 7 ⁄8″ (55.5 cm) min. cutout depth
---|---
Minimum Installation Clearances
For proper installation, the following minimum clearances must exist above and
below the cabinet opening.
Installation Above Single Built-In Oven
INSTALLATION INSTRUCTIONS
Assemble Spacer Kit
- Attach bottom vent to spacer bars using four ³⁄8″ hex washer head screws.
NOTE: Spacer bar flanges should be facing out.
Install Spacer Kit
- Center assembled microwave oven spacer kit against lower, front edge of the cabinet cutout.
- Using an ¹⁄8″ (3.2 mm) drill bit, drill through the mounting holes in the spacer bars to create pilot holes.
- Attach the assembled spacer kit to the cabinet using four ¾” pan head screws provided. Do not overtighten screws.
Install Microwave Oven
Follow the instructions below along with the instructions in the Electric
Built-In Microwave Oven Installation Instructions.
Read the “Electrical Requirements” and “Electrical Connection” sections along
with all other sections of the Installation Instructions before installing the
microwave oven.
WARNING
Excessive Weight Hazard
Use two or more people to move and install microwave oven.
Failure to do so can result in back or other injury.
-
Using 2 or more people, lift microwave oven partially into cabinet cutout above spacer kit and place microwave oven in between spacer bar flanges.
NOTE: Open microwave oven door and push against seal area of microwave oven front frame when pushing microwave oven into cabinet. Do not push against outside edges. -
Push against the front frame of the microwave oven to push oven into cabinet. Push microwave oven completely into cabinet and center in cabinet cutout.
Complete Installation
- Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.
- Check that you have all of your tools.
- Dispose of/recycle all packaging materials.
If you need Assistance or Service:
Please reference the “Assistance or Service” section of the Use and Care
Guide, or contact the dealer from whom you purchased your built-in microwave
oven spacer kit.
® /™ ©2016. Used under license in Canada.
All rights reserved.
W11039684A
Documents / Resources
|
KitchenAid KMBP107EBS Built In Microwave
Oven
[pdf] Instruction Manual
KMBP107EBS, KMBP107ESS, KMBP100ESS, KMBP107EBS Built In Microwave Oven,
KMBP107EBS, Built In Microwave Oven, In Microwave Oven, Microwave Oven, Oven
---|---