SSL SRC50 Mini Rear View Flush Mount Camera User Manual
- June 14, 2024
- SSL
Table of Contents
SSL SRC50 Mini Rear View Flush Mount Camera
Product Information
- Specifications
- Max. Relative Humidity: 95%
- White Balance: Auto
- Illumination: Min. 0.1 lux
- Automatic Gain Control (AGC): Auto
- Resolution (TV lines): 480
- Electronic Shutter Speed: 1/60 (NTSC)
- Effective Pixels: 648 x 488
- Flush Mount Hole: 0.73 (18.5 mm)
- Cable Length: 197/5m (video cable), 39/1m (power cable)
Product Usage Instructions
-
Wiring
- Connect the video cables.
- For the front camera, connect one yellow RCA plug of the video cable to the Front Camera Input RCA socket on your head unit.
- For the rear camera, connect one yellow RCA plug of the video cable to the Rear Camera Input RCA socket on your head unit.
- Connect the other yellow RCA plug of the video cable to the yellow RCA socket on the camera.
- Connect the power cables.
- For the front camera, connect the red split wire of the video cable to the Front Camera Power Output wire on your head unit.
- For the rear camera, connect the red split wire of the video cable to the Rear Camera Power Output wire on your head unit.
- Connect the other red split wire of the video cable to the red wire of the power cable.
- Connect the black (ground) wire of the power cable to the car chassis.
- Connect the black plug of the power cable to the red socket on the camera.
-
Mounting Options
-
Option 1: Flush mount
Select a suitable location on the front or rear of your vehicle (e.g. front or rear bumper). Use the supplied installation bit (0.73/18.5mm) to drill a hole which is used to secure the camera. Flush mount the camera as illustrated in the manual. No screws are required. -
Option 2: Hanging mount
Select a suitable location on the front or rear of your vehicle (e.g. front or rear bumper). Cut an appropriate hole for the camera cable, and drill two screw holes for the mounting bracket. Use two proper screws to fix the supplied bracket, then attach the camera to the bracket as illustrated in the manual.
-
-
Troubleshooting
If you encounter any issues with your camera, refer to the following troubleshooting steps:- Problem: No image
- Solution: Ensure the camera’s power cable is securely plugged. Ensure there is correct and secure wiring between the camera and your head unit. Ensure the reverse input wire on your head unit is connected to the vehicle’s reverse light. Ensure correct camera settings on your head unit.
- Problem: The image is blurry
- Solution: Check for water drops or dust on the camera lens. Clean it with a damp, fiber-free cloth.
- Problem: Image shaking
- Solution: Ensure the camera is tightly mounted.
- Problem: Image slanted
- Solution: Adjust the camera mounting bracket.
-
FAQ (Frequently Asked Questions)
- Q: What is the purpose of this camera?
- A: This camera is designed for use as a front-view or rear-facing backup camera and is mounted on the vehicle’s front or rear bumper.
- Q: How is the camera triggered?
- A: When installed with any of our camera-capable head units, the camera view can be automatically triggered when shifting into reverse or manually triggered by selecting the camera button from the head unit home screen.
- Q: What should I do before using the product?
- A: Please read and understand all instructions before using your product. Failure to follow the instructions could result in injury and/or damage that could potentially void the warranty.
- Q: Can the camera detect all obstacles?
- A: No, certain obstacles may not be detected or not reliably detected.
Introduction
- This camera is designed for use as a front-view or rear-facing backup camera and is mounted on the vehicle’s front or rear bumper.
- When installed with any of our camera-capable head units, the camera view can be automatically triggered when shifting into reverse or manually triggered by selecting the camera button from the head unit home screen.
Package Contents
- 1x Camera with power and video sockets
- 1x Power cable with power plug
- 1x Video cable with two yellow RCA plugs
- Camera mounting kit (including one installation bit)
- User manual
Important
- Please read and understand all instructions before you use your product. Failure to follow the instructions could result in injury and/or damage that could potentially void the warranty.
Important safety precautions
- Use of the camera must not replace other safe driving habits. Precise control and looking around before backing up is necessary.
- Always remember that the area displayed by the camera is limited, and certain obstacles may not be detected or not reliably detected.
Installation precautions
WARNING: Always consult a professional installer.
- Improper wiring and mounting of the camera can cause damage, injury, or accident.
- Have installation performed by a professional only. Contact our technical support for any installation questions.
- Disconnect the negative terminal of the vehicle battery prior to wiring.
- Hide wires under the car floor mat or through the car headliner.
- Make sure wires are not squeezed or damaged by sharp edges. Use rubber grommets if passing through sheet metal.
Wiring
- Follow the two steps described below to install this product as a front camera or a rear camera.
- The rear camera view automatically turns on when reversing.
- Ensure you connect the “Reverse Input” wire on your head unit to the vehicle’s reverse light for the reverse trigger.
- The front camera view is not accessible when reversing.
- Both rear and front camera views can be selected via Home screen options on your head unit.
- Connect the video cables.
- a Connect one yellow RCA plug of the video cable to your head unit.
- Front camera: to “Front Camera Input” RCA socket.
- Rear camera: to “Rear Camera Input” RCA socket.
- b Connect the other yellow RCA plug of the video cable to the yellow RCA socket on the camera.
- Connect the power cables.
- c Connect the red split wire of the video cable to your head unit.
- Front camera: to “Front Camera Power Output” wire.
- Rear camera: to “Rear Camera Power Output” wire.
- d Connect the other red split wire of the video cable to the red wire of the power cable.
- e Connect the black (ground) wire of the power cable to the car chassis.
- f Connect the black plug of the power cable to the red socket on the camera.
Mounting
Important notes on mounting
- When making modifications to the vehicle due to the installation, make sure the traffic safety and stability of the vehicle are not impaired.
- When drilling or cutting any holes in your vehicle, make sure the fuel tank, fuel lines, hydraulic lines, and electrical wiring are not damaged.
Option 1: Flush mount
- Select a suitable location on the front or rear of your vehicle (e.g. front or rear bumper). Then use the supplied installation bit (0.73”/18.5mm) to drill a hole which is used to secure the camera.
- Flush mount the camera as illustrated below. No screws are required.
Option 2: Hanging mount
- Select a suitable location on the front or rear of your vehicle (e.g. front or rear bumper). Then cut an appropriate hole for the camera cable, and drill two screw holes for the mounting bracket.
- Use two proper screws to fix the supplied bracket then attach the camera to the bracket as illustrated below.
Troubleshooting
| Problem | Solution |
|---|---|
| No image | Ensure the camera’s power cable is securely plugged. |
Ensure there is correct and secure wiring between the camera and your head unit.
Ensure the reverse input wire on your head unit is connected to the vehicle’s reverse light.
Ensure correct camera settings on your head unit.
Image blurry| Check for water drops or dust on the camera lens.
Clean it with a damp, fiber-free cloth.
Image shaking| Ensure the camera is tightly mounted.
Image slanted| Adjust the camera mounting bracket.
Image Setting
- To remove the on-screen parking guidelines, cut the white wire loop which splits from the camera’s cable.
- Make sure to unplug the power cable from the camera and plug it in again to enable the new setting (after cutting the white wire loop).
Specifications
- Power supply………………………………12 VDC
- Viewing angle……………………………..170°
- TV system…………………………………..NTSC
- Video output……………………………….1.0 vp-p, 75 Ω
- S/N ratio……………………………………..≤45 dB
- Ingress protection rating……………….IP67 (waterproof)
- Operating conditions……………………. -22 to +140°F (-30 to +60°C) max. 95% RH
- White balance……………………………..Auto
- Illumination…………………………………min. 0.1 lux
- Automatic gain control (AGC)………..Auto
- Resolution (TV lines)……………………480
- Electronic shutter speed………………. 1/60 (NTSC)
- Effective pixels…………………………….648 x 488
- Flush mount hole…………………………0.73” (18.5 mm)
- Cable length………………………………. 197”/5m (video cable); 39”/1m (power cable); 20”/0.5m (camera’s cable)
Specifications are subject to change without notice.
CONTACT
- SOUND STORM LABORATORIES
- 3451 Lunar Court, Oxnard CA 93030
- TECHNICAL ASSISTANCE
- www.soundstormlab.com/support.
- 805-751-4855 Customer Service 0723
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>