MSI MPG B650I EDGE WIFI Motherboard User Guide
- June 14, 2024
- MSI
Table of Contents
MPG B650I EDGE WIFI
Motherboard
User Guide
Quick Start
Thank you for purchasing a new motherboard from MSI®. This Quick Start section provides demonstration diagrams about how to install your computer. Some of the installations also provide video demonstrations. Please link to the URL to watch it with the web browser on your phone or tablet. You may have even link to the URL by scanning the QR code.
Preparing Tools and Components
Safety Information
- The components included in this package are prone to damage from electrostatic discharge (ESD). Please adhere to the following instructions to ensure successful computer assembly.
- Ensure that all components are securely connected. Loose connections may cause the computer to not recognize a component or fail to start.
- Hold the motherboard by the edges to avoid touching sensitive components.
- It is recommended to wear an electrostatic discharge (ESD) wrist strap when handling the motherboard to prevent electrostatic damage. If an ESD wrist strap is not available, discharge yourself of static electricity by touching another metal object before handling the motherboard.
- Store the motherboard in an electrostatic shielding container or on an anti-static pad whenever the motherboard is not installed.
- Before turning on the computer, ensure that there are no loose screws or metal components on the motherboard or anywhere within the computer case.
- Do not boot the computer before installation is completed. This could cause permanent damage to the components as well as injury to the user.
- If you need help during any installation step, please consult a certified computer technician.
- Always turn off the power supply and unplug the power cord from the power outlet before installing or removing any computer component.
- Keep this user guide for future reference.
- Keep this motherboard away from humidity.
- Make sure that your electrical outlet provides the same voltage as is indicated on the PSU, before connecting the PSU to the electrical outlet.
- Place the power cord such a way that people can not step on it. Do not place anything over the power cord.
- All cautions and warnings on the motherboard should be noted.
- If any of the following situations arises, get the motherboard checked by service personnel:
- Liquid has penetrated into the computer.
- The motherboard has been exposed to moisture.
- The motherboard does not work well or you can not get it work according to user guide.
- The motherboard has been dropped and damaged.
- The motherboard has obvious sign of breakage.
- Do not leave this motherboard in an environment above 60°C (140°F), it may damage the motherboard.
Installing a Processor
Important
If you are installing the screw-type CPU heatsink, please follow the figure
below to remove the retention module first and then install the heatsink.
Installing DDR5 memory
Connecting the Front Panel Header
Installing the Motherboard
Connecting the Power Connectors
Installing SATA Drives
Installing a Graphics Card
Connecting Peripheral Devices
Power On
Specifications
CPU| • Supports AMD Ryzen™ 7000 Series Desktop Processor*
• Processor socket AM5
- Please go to www.msi.com to get the newest support status as new processors are released.
---|---
Chipset| AMD B650 Chipset
Memory| • 2x DDR5 memory slots, supporting up to 96GB*
• Supports 1R 4800 MHz by JEDEC
• Max. overclocking frequency:
• 1DPC 1R Max. speed up to 6000+ MHz
• 1DPC 2R Max. speed up to 6000+ MHz
• Supports Dual-Channel mode
• Supports non-ECC, un-buffered memory
• Supports AMD EXPO - Please refer to www.msi.com for more information on compatible memory.
Expansion Slots| • 1x PCIe x16 slot (From CPU)
• Supports up to PCIe 4.0 x16
Onboard Graphics| • 1x HDMI™ 2.1 port with FRL, supports a maximum resolution of 4K 120Hz* / ** - Available only on processors featuring integrated graphics.
* Graphics specifications may vary depending on the CPU installed.
SATA Ports| • 4x SATA 6Gb/s ports (From B650 chipset)
M.2 SSD Slots| • 2x M.2 slots (Key M)
• M2_1 slot (From CPU)
• Supports up to PCIe 4.0 x4
• Supports 2260/ 2280 storage devices
• M2_2 slot (From chipset)
• Supports up to PCIe 4.0 x4
• Supports 2260/ 2280 storage devices
RAID| • Supports RAID 0 , RAID 1 and RAID 10 for SATA storage devices
• Supports RAID 0 and RAID 1 for M.2 NVMe storage devices
Audio| Realtek® ALC4080 Codec
• 7.1-Channel USB High Performance Audio
• Supports up to 32-bit/384kHz playback on front panel.
LAN| • 1x Realtek® 8125 2.5Gbps LAN controller
Wi-Fi & Bluetooth®| AMD Wi-Fi 6E
• The Wireless module is pre-installed in the M.2 (Key-E) slot
• Supports MU-MIMO TX/RX
• Supports 20MHz, 40MHz, 80MHz,160MHz bandwidth in
2.4GHz/ 5GHz or 6GHz bands
• Supports 802.11 a/ b/ g/ n/ ac/ ax
• Supports Bluetooth® 5.2** - The usage of Wi-Fi 6GHz band relies on Windows 11 support and depends on every country’s regulations.
** The Bluetooth version may be updated, please refer to the Wi-Fi chipset vendor’s website for details.
Power Connectors| • 1x 24-pin ATX main power connector
• 1x 8-pin +12V power connector
Internal USB
Connectors| • 1x USB 3.2 Gen 2 10Gbps Type-C front panel port (From B650 chipset)
• 1x USB 3.2 Gen 1 5Gbps connector (From B650 chipset)
• Supports additional 2 USB 3.2 Gen 1 5Gbps ports
• 1x USB 2.0 connector (From B650 chipset)
• Supports additional 2 USB 2.0 ports
Fan Connectors| • 1x 4-pin CPU fan connector
• 1x 4-pin water-pump fan connector
• 1x 4-pin system fan connector
System Connectors| • 1x Front panel audio connector
• 2x System panel connectors
• 1x Chassis Intrusion connector
Jumpers| • 1x OC safe boot jumper
LED Features| • 1x 3-pin A-RAINBOW V2 (ARGB Gen2) LED connector
• 4x EZ Debug LED
Back Panel
Connectors| • 1x Clear CMOS button
• 1x Flash BIOS button
• 1x HDMI™ port
• 2x USB 3.2 Gen 1 5Gbps Type-A ports (From CPU)
• 2x USB 3.2 Gen 2 10Gbps Type-A port (From CPU)
• 1x USB 3.2 Gen 2 10Gbps Type-A port (From B650 chipset)
• 1x USB 3.2 Gen 2×2 20Gbps Type-C port (From B650 chipset)
• 1x 2.5 Gbps LAN (RJ45) port
• 2x Wi-Fi antenna connectors
• 3x audio jacks
I/O Controller| NUVOTON NCT6687-R Controller Chip
Hardware Monitor| • CPU/ System/ Chipset temperature detection
• CPU/ System/ Pump/ chipset fan speed detection
• CPU/ System/ Pump/ chipset fan speed control
Form Factor| • Mini-ITX Form Factor
• 6.7 in. x 6.7 in. (170 mm x 170 mm)
BIOS Features| • 1x 256 Mb flash
• UEFI AMI BIOS
• ACPI 6.4, SMBIOS 3.5
• Multi-language
Software| • Drivers
• MSI Center
• MSI APP Player (BlueStacks)
• CPU-Z MSI GAMING
• Norton 360 Deluxe
• AIDA64 Extreme – MSI Edition
Special Features
MSI Center
- Gaming Mode
- Smart Priority
- Game Highlights
- Mystic Light (Sync & control)
- Ambient Link
- Frozr AI Cooling
- User Scenario
- True Color
- Live Update
- Hardware Monitoring
- Super Charger
- Device Speed Up
- Smart Image Finder
- MSI Companion
- System Diagnosis
- System Info
- Microsoft APP My Device
- MSI Display kit
Thermal Features
- Extended Heatsink Design
- MOSFET Baseplate
- M.2 Shield Frozr
- K7 MOSFET thermal pad/ Extra choke pad
- Fan headers (CPU + PUMP + SYSTEM)
Performance
- Core Boost
- VRM Power Design
- Memory Boost
- Lightning Gen 4 PCI-E/ M.2 Slot
- Front USB Type-C
- Server Grade PCB
- 2oz Copper thickened PCB
DIY Friendly
- PCI-E Steel Armor
- Pre-installed I/O Shield
- EZ DEBUG LED
- EZ LED Control
- Flash BIOS Button
Audio
- Audio Boost 5
RGB Support
- Mystic Light Extension (A-RAINBOW V2)
- Ambient Link Support
BIOS
- Click BIOS 5
Package Contents
Please check the contents of your motherboard package. It should contain:
Board
- 1x Motherboard
Documentation
- 1x Quick installation guide
- 1x European Union regulatory notice
Cables
- 2x SATA6Gb/s cables
- 1x JARGB extension cable
Accessories
- 1x Wi-Fi antenna set
- 1x Cable sticker
- 3x M.2 screws
Important
If any of the above items are damaged or missing, please contact your
retailer.
Back Panel Connectors
Item | Description |
---|---|
1 | Clear CMOS button |
2 | HDMI™ port |
3 | USB 3.2 Gen 1 5Gbps Type-A ports (From CPU) |
4 | USB 3.2 Gen 2 10Gbps Type-A ports (From CPU) |
5 | 2.5 Gbps LAN jack |
6 | Wi-Fi Antenna connectors |
7 | Line-In jack |
8 | Flash BIOS button – Please refer to page 48 for details about updating BIOS |
with Flash BIOS button.
9| USB 3.2 Gen 2 10Gbps Type-A port (From CPU)
∙ Flash BIOS port
10| USB 3.2 Gen 2×2 (20Gbps) Type-C port (From B650 chipset)
11| USB 3.2 Gen 2 10Gbps Type-A port (From B650 chipset)
12| Line-Out jack
13| Mic-In jack
LAN Port LED Status Table
Audio Jacks Connection
Audio jacks to headphone and microphone diagram
Audio jacks to stereo speakers diagram
Audio jacks to 4-channel speakers diagram
Audio jacks to 5.1-channel speakers diagram
Audio jacks to 7.1-channel speakers diagram
Installing Antennas
- Screw the antennas tight to the antenna connectors as shown below.
- Orient the antennas.
Overview of Components
Front view
Bottom view
CPU Socket
Introduction to the AM5 CPU
The surface of the AM5 CPU has two notches and a golden triangle to assist in
correctly lining up the CPU for motherboard placement. The golden triangle is
the Pin 1 indicator.
Important
- When changing the processor, the system configuration could be cleared and reset BIOS to default values, due to the AM5 processor’s architecture.
- Always unplug the power cord from the power outlet before installing or removing the CPU.
- Please retain the CPU protective cap after installing the processor. MSI will deal with Return Merchandise Authorization (RMA) requests if only the motherboard comes with the protective cap on the CPU socket.
- When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink is necessary to prevent overheating and maintain system stability.
- Confirm that the CPU heatsink has formed a tight seal with the CPU before booting your system.
- Overheating can seriously damage the CPU and motherboard. Always make sure the cooling fans work properly to protect the CPU from overheating. Be sure to apply an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to enhance heat dissipation.
- Whenever the CPU is not installed, always protect the CPU socket pins by covering the socket with the plastic cap.
- If you purchased a separate CPU and heatsink/ cooler, Please refer to the documentation in the heatsink/ cooler package for more details about installation.
- This motherboard is designed to support overclocking. Before attempting to overclock, please make sure that all other system components can tolerate overclocking. Any attempt to operate beyond product specifications is not recommended. MSI® does not guarantee the damages or risks caused by inadequate operation beyond product specifications.
DIMM Slots
Important
- Always insert memory modules in the DIMMB1 slot first.
- To ensure system stability for Dual channel mode, memory modules must be of the same type, number and density.
- Some memory modules may operate at a lower frequency than the marked value when overclocking due to the memory frequency operates dependent on its Serial Presence Detect (SPD). Go to BIOS and find the DRAM Frequency to set the memory frequency if you want to operate the memory at the marked or at a higher frequency.
- It is recommended to use a more efficient memory cooling system for full DIMMs installation or overclocking.
- The stability and compatibility of installed memory module depend on installed CPU and devices when overclocking.
- Please refer to www.msi.com for more information on compatible memory.
PCI_E1: PCIe Expansion Slot
Important
- If you install a large and heavy graphics card, you need to use a tool such as MSI Graphics Card Bolster to support its weight to prevent deformation of the slot.
- When adding or removing expansion card, always turn off the power supply and unplug the power supply power cable from the power outlet. Read the expansion card’s documentation to check for any necessary additional hardware or software changes.
M2_1~2: M.2 Slots (Key M)
Important
If your M.2 SSD equips its own heatsink, please remove the M.2 plate or rubber
cube in the M.2 slot before installing M.2 SSD. Do not re-install the heatsink
supplied with your motherboard.
Installing M.2 module into M2_1 slot
-
Loosen the screws of M.2 Shield Frozr heatsink.
-
Remove the M.2 Shield Frozr and remove the protective films from the thermal pad under the M.2 Shield Frozr.
-
Remove the protective films from the thermal pad on the M.2 plate.
-
Move and fasten the M.2 standoff screw to the appropriate location for 2260 M.2
SSD. Skip this step if you install 2280 SSD. -
Insert your M.2 SSD into the M2_1 slot at a 30-degree angle.
-
Secure the M.2 SSD in place with the supplied M.2 screw.
-
Put the M.2 Shield Frozr heatsink back in place and secure it.
Installing M.2 module into M2_2 slot
- Insert your M.2 SSD into the M2_2 slot at a 30-degree angle.
- Secure the M.2 SSD in place with the supplied M.2 screw.
SATA_1~4: SATA 6Gb/s Connectors
These connectors are SATA 6Gb/s interface ports. Each connector can connect to
one SATA device.
Important
- Please do not fold the SATA cable at a 90-degree angle. Data loss may result during transmission otherwise.
- SATA cables have identical plugs on either sides of the cable. However, it is recommended that the flat connector be connected to the motherboard for space saving purposes.
JAUD1: Front Audio Connector
This connector allows you to connect audio jacks on the front panel.
Pin | Signal Name | Pin | Signal Name |
---|---|---|---|
1 | MIC L | 2 | Ground |
3 | MIC R | 4 | NC |
5 | Head Phone R | 6 | MIC Detection |
7 | SENSE_SEND | 8 | No Pin |
9 | Head Phone L | 10 | Head Phone Detection |
JFP1, JFP2: Front Panel Connectors
The JFP1 connector controls the power on, power reset, and the LEDs on your PC
case/chassis. Power Switch/ Reset Switch headers allow you to connect power
button/reset button. Power LED header connects to LED light on the PC case,
and HDD LED header indicates the activity of the hard disk. The JFP2 connector
is for Buzzer and Speaker. To connect the cables from PC case to the right
pins, please refer to the following images below.
Important
Please note that Power LED and HDD LED have positive and negative connection,
you need to link up the cable to the corresponding positive and negative port
on the motherboard. Otherwise, LEDs won’t work properly.
CPU_PWR1, ATX_PWR1: Power Connectors
These connectors allow you to connect an ATX power supply.
CPU_PWR1
Pin | Signal Name | Pin | Signal Name |
---|---|---|---|
1 | Ground | 2 | Ground |
3 | Ground | 4 | Ground |
5 | +12V | 6 | +12V |
7 | +12V | 8 | +12V |
ATX_PWR1
Pin | Signal Name | Pin | Signal Name |
---|---|---|---|
1 | +3.3V | 2 | +3.3V |
3 | Ground | 4 | +5V |
5 | Ground | 6 | +5V |
7 | Ground | 8 | PWR OK |
9 | 5VSB | 10 | +12V |
11 | +12V | 12 | +3.3V |
13 | +3.3V | 14 | -12V |
15 | Ground | 16 | PS-ON# |
17 | Ground | 18 | Ground |
19 | Ground | 20 | Res |
21 | +5V | 22 | +5V |
23 | +5V | 24 | Ground |
Important
Make sure that all the power cables are securely connected to a proper ATX
power supply to ensure stable operation of the motherboard.
JCI1: Chassis Intrusion Connector
This connector allows you to connect the chassis intrusion switch cable.
Using chassis intrusion detector
- Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis.
- Close the chassis cover.
- Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration.
- Set Chassis Intrusion to Enabled.
- Press F10 to save and exit and then press the Enter key to select Yes.
- Once the chassis cover is opened again, a warning message will be displayed on screen when the computer is turned on.
Resetting the chassis intrusion warning
- Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration.
- Set Chassis Intrusion to Reset.
- Press F10 to save and exit and then press the Enter key to select Yes.
JUSB1: USB 3.2 Gen 2 10Gbps Type-C front panel Connector
This connector allows you to connect USB Type-C connector on the front panel.
The connector possess a foolproof design. When you connect the cable, be sure
to connect it with the corresponding orientation.
JUSB2: USB 3.2 Gen 1 Connector
These connectors allow you to connect USB 3.2 Gen 1 5Gbps ports on the front
panel.
Pin | Signal Name | Pin | Signal Name |
---|---|---|---|
1 | Power | 2 | USB3_RX_DN |
3 | USB3_RX_DP | 4 | Ground |
5 | USB3_TX_C_DN | 6 | USB3_TX_C_DP |
7 | Ground | 8 | USB2.0- |
9 | USB2.0+ | 10 | Ground |
11 | USB2.0+ | 12 | USB2.0- |
13 | Ground | 14 | USB3_TX_C_DP |
15 | USB3_TX_C_DN | 16 | Ground |
17 | USB3_RX_DP | 18 | USB3_RX_DN |
19 | Power | 20 | No Pin |
Important
Note that the Power and Ground pins must be connected correctly to avoid
possible damage.
JUSB3: USB 2.0 Connector
This connector allows you to connect USB 2.0 ports on the front panel.
Pin | Signal Name | Pin | Signal Name |
---|---|---|---|
1 | VCC | 2 | VCC |
3 | USB0- | 4 | USB1- |
5 | USB0+ | 6 | USB1+ |
7 | Ground | 8 | Ground |
9 | No Pin | 10 | NC |
Important
- Note that the VCC and Ground pins must be connected correctly to avoid possible damage.
- In order to recharge your iPad, iPhone and iPod through USB ports, please install MSI Center utility.
CPU_FAN1, PUMP_FAN1, SYS_FAN1: Fan Connectors
Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC
Mode.
PWM Mode fan connectors provide constant 12V output and adjust fan speed with
speed control signal. DC Mode fan connectors control fan speed by changing
voltage.
The auto mode fan connectors can automatically detect PWM and DC mode.
You can control fans in BIOS> HARDWARE MONITOR panel. It allows you to set DC
or PWM to your fan type. Check the Smart Fan Mode, the fan speed will change
according to the CPU or system temperature. Uncheck the Smart Fan Mode, the
fan will spin at maximum speed.
Important
Make sure fans are working properly after switching the PWM/ DC mode.
PWM Mode pin definition
Pin | Signal Name | Pin | Signal Name |
---|---|---|---|
1 | Ground | 2 | +12V |
3 | Sense | 4 | Speed Control Signal |
DC Mode pin definition
Pin | Signal Name | Pin | Signal Name |
---|---|---|---|
1 | Ground | 2 | Voltage Control |
3 | Sense | 4 | NC |
Fan connector specifications
Connector | Default fan mode | Max. current | Max. power |
---|---|---|---|
CPU_FAN1 | Auto mode | 3A | 36W |
PUMP_FAN1 | PWM mode | 3A | 36W |
SYS_FAN1 | DC mode | 2A | 24W |
JOCFS1: Safe Boot Jumper
This jumper is used for Safe Boot. Once enabled, the system will boot with
default settings and lower PCIe (from CPU) mode.
| Normal (default)
Boot with the saved
BIOS settings.
---|---
| Enabled
Apply the BIOS default settings and lower PCIe (from CPU) mode for Safe Boot.
BAT1: CMOS Battery
If the CMOS battery is out of charge, the time in the BIOS will be reset and
the data of system configuration will be lost. In this case, you need to
replace the CMOS battery.
Replacing CMOS batter
- Unplug the battery wire from the BAT1 connector and remove the battery.
- Connect the new CR2032 battery with wire to the BAT1 connector.
WARNING
KEEP OUT OF REACH OF CHILDREN
- Swallowing can lead to chemical burns, perforation of soft tissue, can death.
- Severe burns can occur within 2 hours of ingestion.
- If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
JARGB_V2: A-RAINBOW V2 (ARGB Gen2) LED connector
The JARGB_V2 connector allows you to connect the ARGB Gen2 and the ARGB-based
LED strips. The JARGB_V2 connector supports up to 240 individually addressable
RGB LEDs with maximum power rating of 3A (5V).
Pin | Signal Name | Pin | Signal Name |
---|---|---|---|
1 | +5V | 2 | Data |
3 | No Pin | 4 | Ground |
Addressable RGB LED Strip Connection
Addressable RGB LED Fan Connection
CAUTION
Do not connect the wrong type of LED strips. The JRGB connector and the
JARGB_V2 connector provide different voltages, and connecting the ARGB 5V LED
strip to the JRGB connector will result in damage to the LED strip.
Important
- If you connect the ARGB Gen1 and ARGB Gen2 LED strips into the same connector, it may cause some issues. Please do not mix the ARGB Gen1 LED and the ARGB Gen2 LED strips together.
- It is recommended that you install LED strips with the same specification to achieve the best effects.
- Always turn off the power supply and unplug the power cord from the power outlet before installing or removing the addressable RGB LED strip.
- Please use MSI’s software to control the extended LED strip.
EZ Debug LED
These LEDs indicate the debug status of the motherboard.
| CPU – indicates CPU is not detected or fail.
---|---
| DRAM – indicates DRAM is not detected or fail.
| VGA – indicates GPU is not detected or fail.
| BOOT – indicates the booting device is not detected or fail.
Installing OS, Drivers & MSI Center
Please download and update the latest utilities and drivers at www.msi.com
Installing Windows 10/ Windows 11
- Power on the computer.
- Insert the Windows 10/ Windows 11 installation disc/USB into your computer.
- Press the Restart button on the computer case.
- Press F11 key during the computer POST (Power-On Self Test) to get into Boot Menu.
- Select the Windows 10/ Windows 11 installation disc/USB from the Boot Menu.
- Press any key if screen shows Press any key to boot from CD or DVD… message. If not, please skip this step.
- Follow the instructions on the screen to install Windows 10/ Windows 11.
Installing Drivers with MSI Driver Utility Installer
Important
- Some new network chips have not been natively supported by Windows 10/ Windows 11. It is recommended that the LAN driver be installed before installing drivers with MSI Driver Utility Installer. Please refer to www.msi.com to install the LAN driver for your motherboard.
- The MSI Driver Utility Installer will only pop up once. If you cancel or close it during the process, please refer to the Live Update chapter of the MSI Center manual to install the drivers. You can also go to www.msi.com to search your motherboard and download the drivers.
- MSI Driver Utility Installer needs to be installed over the internet.
1. Start up your computer in Windows 10/ Windows 11.
2. Select Start > Settings > Windows Update, and then select Check for updates.
3. MSI Driver Utility Installer will pop up automatically.
4. Select the I have read and agree to the MSI Terms of Use check box, and then click Next.
6. Once the progress has completed, click Finish.
MSI Center
MSI Center is an application that helps you easily optimize game settings and
smoothly use content creation softwares. It also allows you to control and
synchronize LED light effects on PCs and other MSI products. With MSI Center,
you can customize ideal modes, monitor system performance, and adjust fan
speed.
MSI Center User Guide
If you would like to know more information about MSI Center, please refer to http://download.msi.com/manual/mb/MSICENTER.pdf or scan the QR code to access.
Important
Functions may vary depending on the product you have.
UEFI BIOS
MSI UEFI BIOS is compatible with UEFI (Unified Extensible Firmware Interface)
architecture. UEFI has many new functions and advantages that traditional BIOS
cannot achieve, and it will completely replace BIOS in the future. The MSI
UEFI BIOS uses UEFI as the default boot mode to take full advantage of the
new chipset’s capabilities.
Important
The term BIOS in this user guide refers to UEFI BIOS unless otherwise noted.
UEFI advantages
- Fast booting – UEFI can directly boot the operating system and save the BIOS selftest process. And also eliminates the time to switch to CSM mode during POST.
- Supports for hard drive partitions larger than 2 TB.
- Supports more than 4 primary partitions with a GUID Partition Table (GPT).
- Supports unlimited number of partitions.
- Supports full capabilities of new devices – new devices may not provide backward compatibility.
- Supports secure startup – UEFI can check the validity of the operating system to ensure that no malware tampers with the startup process.
Incompatible UEFI cases
- 32-bit Windows operating system – this motherboard supports only Windows 10/ Windows 11 64-bit operating system.
- Older graphics card – the system will detect your graphics card. If you use older graphics cards, it may display a warning message There is no GOP (Graphics Output protocol) support detected in this graphics card.
Important
We recommend that you replace it with a graphics card supporting GOP/UEFI or
use CPU with integrated graphics for having normal function.
How to check the BIOS mode?
- Power on your computer.
- Press Delete key, when the Press DEL key to enter Setup Menu, F11 to enter Boot Menu message appears on the screen during the boot process.
- After entering the BIOS, you can check the BIOS Mode at the top of the screen.
BIOS Mode: UEFI
BIOS Setup
The default settings offer the optimal performance for system stability in
normal conditions. You should always keep the default settings to avoid
possible system damage or failure booting unless you are familiar with BIOS.
Important
- BIOS items are continuously update for better system performance. Therefore, the description may be slightly different from the latest BIOS and should be for reference only. You could also refer to the HELP information panel for BIOS item description.
- The BIOS screens, options and settings will vary depending on your system.
Entering BIOS Setup
Press Delete key, when the Press DEL key to enter Setup Menu, F11 to enter
Boot Menu message appears on the screen during the boot process.
Function key
F1: | General Help list |
---|---|
F2: | Add/ Remove a favorite item |
F3: | Enter Favorites menu |
F4: | Enter CPU Specifications menu |
F5: | Enter Memory-Z menu |
F6: | Load optimized defaults |
F7: | Switch between Advanced mode and EZ mode |
F8: | Load Overclocking Profile |
F9: | Save Overclocking Profile |
F10: | Save Change and Reset* |
F12: | Take a screenshot and save it to USB flash drive (FAT/ FAT32 format |
only).
Ctrl+F:| Enter Search page
- When you press F10, a confirmation window appears and it provides the modification information. Select between Yes or No to confirm your choice.
BIOS User Guide
If you’d like to know more instructions on setting up the BIOS, please refer to https://download.msi.com/archive/mnu_exe/mb/AMDAM5BIOS.pdf or scan the QR code to access.
Important
Functions may vary depending on the product you have.
Resetting BIOS
You might need to restore the default BIOS setting to solve certain problems.
There are several ways to reset BIOS:
- Go to BIOS and press F6 to load optimized defaults.
- Press the Clear CMOS button on the rear I/O panel.
Important
Be sure the computer is off before clearing CMOS data. Please refer to the
Clear CMOS button section for resetting BIOS.
Updating BIOS
Updating BIOS with M-FLASH
Before updating:
Please download the latest BIOS file that matches your motherboard model from
MSI website. And then save the BIOS file into the USB flash drive.
Updating BIOS:
- Switch to the target BIOS ROM by Multi-BIOS switch. Please skip this step if your motherboard doesn’t has this switch.
- Insert the USB flash drive that contains the update file into the USB port.
- Please refer the following methods to enter flash mode.
• Reboot and press Ctrl + F5 key during POST and click on Yes to reboot the system.
Press <Ctrl+F5> to activate M-Flash for BIOS update.
• Reboot and press Del key during POST to enter BIOS. Click the M-FLASH button and click on Yes to reboot the system.
4. Select a BIOS file to perform the BIOS update process.
5. When prompted click on Yes to start recovering BIOS.
6. After the flashing process is 100% completed, the system will reboot automatically.
Updating the BIOS with MSI Center
Before updating:
- Make sure the LAN driver is already installed and the internet connection is set properly.
- Please close all other application software before updating the BIOS.
To update BIOS:
- Install and launch MSI Center and go to Support page.
- Select Live Update and click on Advance button.
- Select the BIOS file and click on Install button.
- The installation reminder will appear, then click the Install button on it.
- The system will automatically restart to update BIOS.
- After the flashing process is 100% completed, the system will restart automatically.
Updating BIOS with Flash BIOS Button
- Please download the latest BIOS file that matches your motherboard model from the MSI® website.
- Rename the BIOS file to MSI.ROM, and save it to the root of the USB storage device.
- Connect the power supply to CPU_PWR1 and ATX_PWR1. (No need to install CPU and memory.)
- Plug the USB storage device that contains the MSI.ROM file into the Flash BIOS Port on the rear I/O panel.
- Press the Flash BIOS Button to update BIOS, and the LED starts flashing.
- The LED will be off when the process is completed.
Block Diagram
MPG B650I EDGE WIFI
Regulatory Notices
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and radiates radio
frequency energy, and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
NOTE
- The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- Shield interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
MSI Computer Corp.
901 Canada Court, City of Industry, CA 91748, USA
(626)913-0828
www.msi.com
CE Conformity
Products bearing the CE marking comply with one or more of the following EU
Directives as may be applicable:
- RED 2014/53/EU
- Low Voltage Directive 2014/35/EU
- EMC Directive 2014/30/EU
- RoHS Directive 2011/65/EU
- ErP Directive 2009/125/EC
Compliance with these directives is assessed using applicable European
Harmonized Standards.
The point of contact for regulatory matters is MSI-Europe: Eindhoven 5706 5692
ER Son.
Products with Radio Functionality (EMF)
This product incorporates a radio transmitting and receiving device. For
computers in normal use, a separation distance of 20 cm ensures that radio
frequency exposure levels comply with EU requirements. Products designed to be
operated at closer proximities, such as tablet computers, comply with
applicable EU requirements in typical operating positions. Products can be
operated without maintaining a separation distance unless otherwise indicated
in instructions specific to the product.
Restrictions for Products with Radio Functionality
| CAUTION: IEEE 802.11x wireless LAN with 5.15~5.35 GHz frequency band is
restricted for indoor use only in all European Union member states, EFTA
(Iceland, Norway, Liechtenstein), and most other European countries (e.g.,
Switzerland, Turkey, Republic of Serbia). Using this WLAN application
outdoors might lead to interference issues with existing radio services.
---|---
| Radio frequency bands and maximum power levels
∙ Features: Wi-Fi 6E, BT
∙ Frequency Range: 2.4 GHz: 2400~2485MHz; 5 GHz: 5150~5350MHz,5470~5725MHz,
5725~5850MHz; 6 GHz: 5955~6415MHz
∙ Max Power Level: 2.4 GHz: 20dBm; 5 GHz: 23dBm; 6 GHz: 23dBm
Wireless Radio Use
This device is restricted to indoor use when operating in the 2.4GHz, 5GHz,
6GHz frequency band.
Compliance Statement of Innovation, Science and Economic Development Canada
(ISED)
This device complies with with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems.
CAN ICES-003(B)/NMB-003(B)
Australia and New Zealand notice
This equipment incorporates a radio transmitting and receiving device. In
normal use, a separation distance of 20 cm ensures that radio frequency
exposure levels comply with the Australian and New Zealand Standards.
Battery Information
European Union:
**** Batteries, battery packs, and accumulators should not be disposed of as
unsorted household waste. Please use the public collection system to return,
recycle, or treat them in compliance with the local regulations.
BSMI:
For better environmental protection, waste batteries should be collected
separately for recycling or special disposal.
California, USA:
The button cell battery may contain perchlorate material and requires special
handling when recycled or disposed of in California.
For further information please visit:
http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
CAUTION: There is a risk of explosion, if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
Chemical Substances Information
In compliance with chemical substances regulations, such as the EU REACH
Regulation (Regulation EC No. 1907/2006 of the European Parliament and the
Council), MSI provides the information of chemical substances in products at:
https://csr.msi.com/global/index
Environmental Policy
- The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life.
- Users should contact the local authorized point of collection for recycling and disposing of their end-of-life products.
- Visit the MSI website and locate a nearby distributor for further recycling information.
- Users may also reach us at gpcontdev@msi.com for information regarding proper Disposal, Take-back, Recycling, and Disassembly of MSI products.
WEEE (Waste Electrical and Electronic Equipment) Statement
To protect the global environment and as an environmentalist, MSI must remind
you that…
Under the European Union (“EU”) Directive on Waste Electrical and Electronic
Equipment, Directive 2002/96/EC, which takes effect on August 13, 2005,
products of “electrical and electronic equipment” cannot be discarded as
municipal wastes anymore, and manufacturers of covered electronic equipment
will be obligated to take back such products at the end of their useful life.
MSI will comply with the product take back requirements at the end of life of
MSIbranded products that are sold into the EU. You can return these products
to local collection points.
India RoHS
This product complies with the “India E-waste (Management and Handling) Rule
2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated
biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1
weight % and 0.01 weight % for cadmium, except for the exemptions set in
Schedule 2 of the Rule.
Copyright and Trademarks Notice
Copyright © Micro-Star Int’l Co., Ltd. All rights reserved. The MSI logo
used is a registered trademark of Micro-Star Int’l Co., Ltd. All other marks
and names mentioned may be trademarks of their respective owners. No warranty
as to accuracy or completeness is expressed or implied. MSI reserves the right
to make changes to this document without prior notice.
The terms HDMI™, HDMI™ High-Definition Multimedia Interface, HDMI™ Trade dress and the HDMI™ Logos are trademarks or registered trademarks of HDMI™ Licensing Administrator, Inc.
Technical Support
If a problem arises with your system and no solution can be obtained from the
user guide, please contact your place of purchase or local distributor.
Alternatively, please try the following help resources for further guidance.
- Visit the MSI website for technical guide, BIOS updates, driver updates, and other information: http://www.msi.com
- Register your product at: http://register.msi.com
Revision History
- Version 1.0, 2022/10, First release.
- Version 1.1, 2023/03, update Wi-Fi information.
- Version 1.2, 2023/05, update memory information.
References
- MSI - Redirect
- Welcome to MSI Member Account Login | MSI Member Center
- 优酷 - 为好内容全力以赴 - 海量正版高清视频在线观看
- dtsc.ca.gov/hazardouswaste/perchlorate/
- MSI - Redirect
- csr
- csr
- 优酷 - 为好内容全力以赴 - 海量正版高清视频在线观看