LUXEVA LXV2000-TS Infrared Wall Patio Heater Waterproof Indoor Instruction Manual

LUXEVA LXV2000-TS Infrared Wall Patio Heater Waterproof Indoor

Specifications

• Main Power: 220-240V AC, 50-60 Hz
• Fuse: 16 Amperes
• Device Type: Heater
• Usage: Domestical
• Compliance: EEE Regulation

Product Usage Instructions

Safety Instructions

This device is manufactured in compliance with safety regulations. Usage against the rules causes harm to person and device.

• Ensure that the main power is 220-240V AC, 50-60 Hz and the power line is connected to the fuse.
• Check the mains safety and ensure that the fuse is 16 Amperes.
• Use the device with a grounded socket placed outside the heater area and away from the hot surface.
• Check if the socket is loose or damaged and avoid using the device with a loose socket.
• Do not connect the device to the same power cable or fuse with another device.
• Avoid leaving the power cord on the hot body of the device or near it.
• If the device will not be used for a long period of time or for cleaning/maintenance purposes, unplug it and ensure it has cooled down.
• This device is not intended for use by persons (including children) with reduced physical, sensory, and mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

Using Your Heater

Before using your heater, please follow the safety instructions mentioned above.

• Ensure that the main power is connected and the device is plugged into a grounded socket.
• Set the desired temperature using the control panel or the remote control (if available).
• Wait for the device to heat up and distribute warm air.
• Adjust the fan speed and oscillation settings (if available) to suit your preference.
• Keep the device away from flammable materials and ensure proper ventilation in the room.
• Do not touch the hot surface of the device during operation.
• When you are done using the heater, unplug it from the socket.

Maintenance and Cleaning

Regular maintenance and cleaning will help ensure the optimal performance and longevity of your heater.

• Before cleaning, make sure the device is unplugged and has cooled down.
• Use a soft cloth to wipe the exterior surface of the heater.
• For stubborn stains, you can use a mild detergent diluted in water. Do not use abrasive cleaners.
• Clean the air inlet and outlet grills using a vacuum cleaner or a soft brush.
• Check for any dust accumulation inside the device and clean it if necessary.

Troubleshooting

If you encounter any issues with your heater, refer to the troubleshooting section in the user manual or contact our customer support for assistance.

FAQ

Q: Can I use this heater in a commercial setting?

A: No, our heaters are designed for domestic use only and not suitable for commercial settings.

Q: Can I use the heater with wet hands?

A: No, it is important to avoid touching the feed cable or using the device with wet hands to prevent electric shock.

Q: How should I clean the heater?

A: Before cleaning, ensure the device is unplugged and cooled down. Use a soft cloth to wipe the exterior surface and clean the air grills with a vacuum cleaner or soft brush. Avoid using abrasive cleaners.

Q: What should I do if the device is not working properly?

A: Refer to the troubleshooting section in the user manual for possible solutions. If the issue persists, please contact our customer support for further assistance.

Dear Customer,

Thank you for the confidence you placed in Luxeva products. Our goal is to ensure that you use this product, which has been manufactured in our modern facilities in precise working conditions, conforming to total quality idea and without harming nature. We recommend that you read and carefully store the User Manual before you use your heater, so that it can preserve its features for a long time and serve you most efficiently.

NOTE:

This User Manual is prepared for more than one model. Some of the features stated in the manual may not be found in your device. These features are denoted with *
Our products are for domestical use, not for commercial use.

“READ THE INSTRUCTIONS BEFORE DEPLOYING OR USING THIS DEVICE.”

This product is manufactured in environment-friendly modern facilities without harming the nature

“It complies with EEE Regulation.”

Safety Instructions

• Do not cover the dust protection cover while the device is operating or hot.

• Children of less than 3 age should be kept away unless continuously supervised.

• Do not use this heater in the vicinity of the bath, shower or swimming pool.

• The heater must not be used if the glass heating elements are damaged.
  CAUTION — Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

• For the safety of children under 8 years of age, the appliance must be operated out of reach, following the specified safety instructions and checking all connections. When out of use, place the heater in a safe place and keep the electrical connection cables (plugs) away from the sockets.

• The expected life of this product is ten years.

• WARNING: This heater is not equipped with a device to control the room temperature. The heater must be used by an experienced person in the presence of children, physical disabilities persons, persons with insufficient experience and inadequate knowledge. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.

Safe distances: high temperature, fire protection, wall mounting (* option)

Technical Features

Device Hardware (Portable Type)

Model

| ****

Height (B)

| ****

Width (A)

| ****

Depth (C)

| Total Power (W)| ****

Feed (V/Hz)

| Drawing Current (A)| ****

Protection Degree

| ****

Device class

---|---|---|---|---|---|---|---|---
LXV2000-TS LXV2000-VR LXV1800

LXV2000

| ****

960 mm

| ****

405 mm

| ****

357 mm

| ****

2000 W

| ****

220-240V~

50/60 Hz

| ****

8.1 A

| ****

IP20

| ****

ı

LXV2500-VR

LXV2200

| 960 mm| 405 mm| 357 mm| 2500 W| 220-240V~

50/60 Hz

| 11.3 A| IP20| ı
LXV1500-VR| 650 mm| 405 mm| 357 mm| 1500 W| 110V~

50/60 Hz

| 13.6 A| IP20| ı
LXV 1200-TS LXV 1200| 650 mm| 405 mm| 357 mm| 1200 W| 220-240V~

50/60 Hz

| 5.5 A| IP20| ı
Model| 1. Level| 2. Level| 3. Level| Thermostat| Remote Control| Control Panel
---|---|---|---|---|---|---
LXV2000-TS| 1000 W| 2000 W|  |  |  | MECHANICAL
LXV2000-VR| 650 W| 1300 W| 2000 W| | | ****

ELECTRONICS

LXV2500-TS| 1250 W| 2500 W|  |  |  | MECHANICAL
LXV2500-VR| 850 W| 1700 W| 2500 W| | | ELECTRONICS
LXV 1800

LXV 2000

| 2000 W|  |  | |  | ****

MECHANICAL

LXV 2200| 2500 W|  |  | |  | ****

MECHANICAL

LXV 1200| 1200 W|  |  | |  | ****

MECHANICAL

LXV 1200-TS| 600 W| 1200 W|  |  |  | ****

MECHANICAL

LXV 1500-VR| 500 W| 1000 W| 1500 W| | | ELECTRONICS

PRODUCT OVERVIEW

1. APPLIANCE BODY
2. ENERGY CABLE
3. FIXED REAR LEG
4. FIXED FRONT LEG
5. ENERGY CABLE FIXING PLASTIC
6. ENERGY CABLE FIXING PLASTIC FITTING SCREW
7. BASE FITTING SCREW
8. CONTROL PROBE
9. CR-NI WIRE GRATE
10. CARBON FILAMENT

Technical Features

Device Hardware (Wall Type)

Model

| Height (A)| Width (B)| Depth (C)| Total

Power (W)

| Feed (V/Hz)| Drawing Current (A)| Protection Degree| Device class
---|---|---|---|---|---|---|---|---
LXV 2000-HR LXV 2000-HRS LXV 2000-H| 185 mm| 810 mm| 110 mm| 2000 W| 220-240V ~,

50/60 Hz

| 8.1 A| IP20| ı
LXV 2500-HR LXV 2500-HRS LXV 2500-H| 185 mm| 810 mm| 110 mm| 2500 W| 220-240V ~,

50/60 Hz

| 11.3 A| IP20| ı
LXV 1500-HR LXV 1500-HRS|

185 mm

|

810 mm

|

110 mm

| 1500 W| 110V ~,

50/60 Hz

|

13.6 A

|

IP20

|

ı

Model

|

1. Level

|

2. Level

|

3. Level

|

Thermostat

|

Remote Control

|

Control Panel

---|---|---|---|---|---|---
LXV 2000-HR LXV 2000-HRS| 650 W| 1300 W| 2000 W| | |

ELECTRONICS

LXV 2500-HR LXV 2500-HRS| 850 W| 1700 W| 2500 W| | |

ELECTRONICS

LXV 1500-HR LXV 1500-HRS| 500 W| 1000 W| 1500 W| | |

ELECTRONICS

Using Of Your Heater

• Plug the device in an appropriate grounding receptacle.
• Bring the on/off switch in working position.
• Attention ! Do not touch the metal terminals on the plug immediately after unplugging it.
• Attention: The device has a safety system. In case of overturning, the safety system will engage and cut off the power.

Control Panel

• Plug the device in an appropriate grounding receptacle.
• Bring the on/off switch in working position.
• Attention ! Do not touch the metal terminals on the plug immediately after unplugging it.

Control Panel

Wall type products can be used in horizontal and vertical positions by loosening the pivot screw as well. The pivot screw must be tightened again after the desired working position is set. WARNING: If the heater is used vertically, the digital display should remain on the bottom.

Remote Control (* Option)

Installing and Replacing Remote Control Batteries
As it can be seen in Figure 1 below, the tabs are pushed in the direction shown by the arrow, it is simultaneously pulled in the direction shown by the arrow in the second figure and the battery is replaced. A new battery is installed using the same method. Only Cr2025 batteries must be used. NOTE: Remove the gelatin from the battery compartment before using the remote for the first time. If the gelatin is not removed, the remote control will not operate .

Note: The point on the right of the screen flashes when the timer of the product is ready. When the time expires, the device switches off and rings an alarm for 1 second.

• 1L, 2L, 3L : Show the power level of the heater.
• 1H, 2H, 3H,…9H : Heater timer indicator (programming up to 9 hours is possible)
• E1: Overheating: If the device overheats in conditions other than the standard operating conditions, it rings an alarm for 10 sec as a warning and stops the heating function.
• E2: After 12 hours of operation, The alarm sounds for 10 seconds and device turns off. E3: Error indicator; it indicates that the device is not balanced.

Without Remote Control

Function Button:   It controls the heat level adjustment and timer adjustment of the heater.

The heat level is increased one level with each pressing. After (L3), it switches to standby mode by pressing the function key again. This button is pressed for 3 sec to perform timer adjustment. The desired time zone in the timer menu is selected by incrementing the 1 step each time the function key is pressed(0H…9H). After waiting 5 sec, the set time zone is active and the light flashes in the lower right corner of the display. To cancel the timer, set the (0H) option from the schedule program, wait 5s. Then timer turns off.

Maintenance and Cleaning

Maintenance
It is very important to perform careful and regular maintenance of the device in accordance with the recommendations made in this manual so that it can run efficiently for a long time.

1. The cleanliness of the reflector (reflecting mirror) and tubes must be checked at least once a month by the user. The cleaning and maintenance instruction must be applied if dirty.
2. According to the amount of dust in the place of use, the said checks should be performed more often.
3. Power cable and plug must be checked while cleaning the device. If there is a deformation in the power cord or the plug, it must be taken to the authorized service.
4. Reflector, wire and body deformation must be visually inspected while cleaning the device. If there is a deformation, authorized service must be called for things to do.
5. It is recommended that the reflector is changed every two years for the device to run more efficiently. Reflector must be changed by the authorized service.
   A clean reflector ensures the maximum level of heating efficiency.

Cleaning
Attention! Regular and careful cleaning performed by the user will ensure that your device will run more efficiently and prolong its life.

1. Your device must be turned off before starting to clean, its power cord must be unplugged from the socket for safety and you must wait until it cools down.
2. If the reflector (reflecting mirror) and carbon flament tube is dirty, it must be cleaned from the outside with dry air without opening the protective cage wire of the device, if possible.
3. The outer surface of the device must be cleaned with a soft cotton cloth or a soft brush.
4. Never use corrosive or melting liquids to clean the heater. These materials may damage the plastic parts.
5. Do not clean your device using vapor cleaners.

Troubleshooting

Please check the points below before calling the technical service about the problems you might encounter with your device.

This device is labelled, in accordance with Council Directive 2002/96/EC, with a symbol of a crossed garbage container. This labelling means that the device, upon end of its life cycle, should not be disposed of together with other house • hold waste. The user is responsible for having the device collected by appropriate entities responsible for disposal of used electrical and electronic devices. Appropriate dispos- al of used electrical and electronic devices allows to avoid hazards to the humans and the environment connected with inappropri ate storage and processing of such devices.

www.luxeva.com.tr

References

• Luxeva – Professional Carbon Heater
• Luxeva – Professional Carbon Heater

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>