amazon basics B0B12PCT2J 30 Inch 55,000 BTU Outdoor Slat Top Square Propane Gas Fire Pit User Manual

B0B12PCT2J 30 Inch 55,000 BTU Outdoor Slat Top Square Propane Gas Fire

Pit

DANGER

CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a camper, tent, car or home.

DANGER
FIRE OR EXPLOSION HAZARD If you smell gas:

• Shut off gas to the appliance.
• Extinguish any open flame.
• If odor continues, leave the area immediately.
• After leaving the area, call your gas supplier or fire department.

Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.

WARNING
Do not store or use gasoline, or other flammable vapors and liquids, in the vicinity of this or any other appliance.
An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
WARNING
For Outdoor Use Only.
Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

WARNING
If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

Important Safeguards

Read these instructions carefully and retain them for future use. If this appliance is passed to a third party, then these instructions must be included.
When using the appliance, basic safety precautions should always be followed to reduce the risk. of injury including the following:

WARNING Risk of injury!
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.
Young children should be carefully supervised when they are in the area of the appliance.
Clothing or other flammable materials should not be hung from the appliance or placed on or near the appliance.
Any guard, barrier, or other protective device removed for servicing the appliance shall be replaced prior to operating the appliance.
Repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that the control  compartment, burners, and circulating air passageways of the appliance are kept clean.
Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control that has been under water.
Do not burn solid fuels in this appliance.
The appliance is intended to be used with a standard 20 lb (9.1 kg) LP gas cylinder (not included). Do not connect the appliance to an LP gas cylinder that exceeds this capacity.
Use the appliance only outdoors. Do not use the appliance in a building, garage, or any other enclosed area.
The appliance is not intended to be installed in or on recreational vehicles and/or boats.
The appliance is not intended for use on wood decks or other flammable surface.
Keep the appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.
Clean and inspect the regulator hose assembly before each use. If there is evidence of abrasion, wear, cuts, or leaks, the regulator hose assembly must be replaced before operating the appliance. Use only the replacement regulator hose assembly specified by the manufacturer (model: T2-LL516).
Locate the hose out of pathways where people may trip over it or in areas where the hose may be subject to accidental damage.
Only use the fire glass provided with the appliance.
Do not use wood chunks, charcoal, lighter fluid, alcohol, paper, or other similar chemicals for lighting or relighting.
Keep all such substances and liquids well away from the appliance when in use.
Keep the regulator hose assembly away from the hot surfaces.
Do not obstruct the flow of combustion and ventilation air to this appliance.
Never operate this appliance unattended.
Do not move the appliance when it is in use.
Always check for gas leaks when connecting or disconnecting an LP gas cylinder to the regulator hose assembly, especially after a prolonged storage period.
The appliance is intended only for operation in temperatures above 32F (0 C).
This appliance is intended for decorative purposes only. Do not use the appliance for cooking.
After using the appliance, turn the control knob to OFF position and cover the main unit with the lid to extinguish the fire completely. Do not pour water on the appliance.
Do not use the appliance in rainy conditions.
For installations at elevations above 2000 ft (610 m), contact your local dealer or gas supplier before installing.
Input ratings should be reduced approximately 4 % for each 1000 ft (305 m) above sea level. Refer to the National Fuel Gas Code, ANSI Z223.1.

Battery Warnings

NOTICE
The battery is not included.

• Always insert battery correctly with regards to polarity (+ and -) marked on the battery and the appliance.
• Exhausted battery should be immediately removed from appliance and properly disposed.

Before First Use

• Remove all the packing materials.
• Remove and review all components before starting assembly.
• Check the appliance for transport damages.
• Clean the appliance before first use. The appliance may emit a slight smell or smoke when it is first used. This is entirely safe and harmless.

Product Description

Preparation

5.1 Choosing a suitable location

The appliance is for outdoor use only. Do not use it inside a building, garage, or any other enclosed areas.
Place the appliance on a stable, level and heat-resistant ground.
Place the appliance in locations with adequate fresh air ventilation.
Place the appliance out of traffic areas and away from combustible materials and structures.
Maintain proper clearances from combustible structures.
Keep a minimum clearance of 48 inches (1.2 m) from sides and rear, and 72 inches (1.8 m) from the top of the appliance to combustible structures.
The appliance can also be used within the following structures:
With walls on all sides, but with no overhead cover

• Within a partial enclosure that includes an overhead cover and no more than two sidewalls in parallel, as in a breezeway

• Within a partial enclosure that includes an overhead cover and no more than two sidewalls at right angles to each other

• Within a partial enclosure that included an overhead cover and three sidewalls, as long as 30 percent or more of the horizontal periphery of the enclosure is permanently open

• Do not store a spare LP cylinder under or near the appliance.

• Keep a minimum distance of 10 feet (3 m) away from the appliance.

• Keep children and pets away from the appliance. When children are near the appliance, they should be carefully supervised by an adult.

• Combustible materials, gasoline, and other flammable vapors or liquids should be situated at least 26 feet (8 m) away from the appliance

5.2 Setting up the appliance
NOTICE
This appliance should be installed, maintained and operated only by an adult. If in doubt, consult a professional.

1. Attach the 2 side panels (G) to the back panel {I) using 4  bolts (1/4″ x 12 mm) (M) and 4 washers (1/4) (0) (Fig. 1).Tighten bolts using screwdriver (R).

2. Attach the front panel (H) using 4 bolts (1/4″ x 12 mm) (M) and 4 washers (1/4″) (0) (Fig. 2). Tighten bolts using screwdriver (R)

3. Attach the door panel (J) using 2 bolts (1/4 x 12 mm) (M) and 2 washers (1/4″) (0) (Fig. 3). Tighten bolts using the wrench (S).

4. Attach the base frame (K) to the bottom of side panels (Gusing 4 bolts (1/4″ x 30 mm) (N) and 4 washers (1/4″) (0) (Fig. 4).
   

5. Attach the control knob (F) to the control panel located under the tabletop (A) (Fig. 5)

6. Unscrew and remove the electronic ignition (E) (Fig. 6). Insert 1×1.5 V AAA (LRO3, alkaline) battery (not provided) in the electronic ignition opening with the positive “+” polarity facing outwards. Then reattach the electronic  ignition (E) (Fig. 6)

7. Put the tabletop (A) and its side and cut the cable tie holding the regulator hose assembly (D) in place (Fig. 7). Take the regulator hose assembly (D) out.

8. Place the tabletop (A) on the assembled frame and ensure the control panel with control knob (Fl is located to the left or right of the door panel (J).

9. Fix the tabletop (A) in place with the 4 wing bolts (M6 x 20 mm) (P) and 4 washers (M8) (Q) (Fig. 8).

5.3 Picking a suitable LP gas cylinder
WARNING Risk of fire!
Do not store a spare LP gas cylinder under or near this appliance.

• Never fill the cylinder beyond 80 % full
• If the information above is not followed exactly, a fire causing death or serious injury may occur.
  A frosty cylinder valve on the LP gas cylinder indicates possible gas overfill. Turn the gas supply off at the LP gas cylinder and contact the liquid propane supplier.

CAUTION Risk of fire!
Only use the gas pressure regulator provided with this appliance. This regulator is set for an outlet pressure of 11 inches water column.

NOTICE
The regulator is equipped with a QCC Type 1 quick closing connection system.

• The regulator does not allow gas to flow until a positive seal has been made.
• The regulator has a thermal element that shuts off the gas flow if the temperature reaches 240 °F (115 °C).
• The regulator has a flow-limiting device that restricts the flow of gas to 10 cubic feet per hour (0.28 cubic meters per hour).
• The liquefied petroleum (LP) cylinder must be constructed and marked in accordance with the specifications for LP
• Gas Cylinders of the U.S. Department of Transportation (D.O.T.) or the National Standard of Canada, CAN/CSA-B339,
• Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission.
• Only use a standard 20 lbs (9 kg) LP gas cylinder with a type 1 – QCC safety valve.
• The LP gas cylinder should be clearly marked with the text “Vapor Withdrawal”, This means it has a propane vapor withdrawal supply system. Position the LP gas cylinder properly for vapor withdrawal.
• The LP gas cylinder must be provided with an overfilling prevention device (OPD).
• The LP gas cylinder must include a collar to protect the LP cylinder valve.
• Do not use an LP gas cylinder if it has a damaged valve/collar, or shows signs of dents, gouges, bulges, fire damage, corrosion, leakage, excessive rust, or other forms of visual external damage. Have the LP gas cylinder checked immediately by a liquid propane supplier.
• Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of  propane.

Connecting/Disconnecting a Gas Cylinder

6.1 Connecting an LP gas cylinder

1. Push in the control knob (Fl and turn it clockwise to OFF position (Fig. 9).

2. Connect the cylinder valve of the regulator hose assembly (D) to the valve outlet of the LP gas cylinder.
   Tighten the securing nut by hand by turning it clockwise (Fig. 10).

3. Insert and place LP cylinder onto the base frame (K) and secure it in place with the wing nut on the base frame (Kl (Fig. 11 ).

4. Close the door panel () (Fig. 12)

6.2 Disconnecting an LP gas cylinder
WARNING Risk of fire or explosion
Do not transport or store the appliance with the LP gas cylinder connected. Before transport or storage, disconnect the LP gas cylinder and store it outdoors.
Do not disconnect the LP gas cylinder while the appliance is in use or is still hot.

1. Push in the control knob (F) and turn it clockwise to OFF position (Fig. 9).

2. Turn the securing nut counter-clockwise by hand. Disconnect the cylinder valve of the regulator hose assembly (D) from the valve outlet of the LP gas cylinder (Fig. 13).

3. Place the dust cap on the valve outlet of the LP gas cylinder when it is not in use. Only install the type of dust cap on the cylinder valve that is provided with the LP gas cylinder.

Gas Leak Test

DANGER Risk of explosion
Perform a gas leak test on the connection between the regulator hose assembly and the LP gas cylinder when  lighting the appliance for the first time, when the LP gas cylinder has been refilled/changed, after a travel over rough or bumpy  roads or after a prolonged period of storage or non-use.
Do not smoke or use any type of flammable material in the area during this gas leak test.
Do not use an open flame to check for leaks. Always use a soapy water solution.

1. Push in the control knob (F) and turn it clockwise to OFF position (Fig. 9).

2. Connect the cylinder valve of the regulator hose assembly (D) to the valve outlet of the LP gas cylinder.
   Tighten the securing nut by hand by turning it clockwise (Fig. 10).

3. Mix a solution of one part of water with one part of liquid soap in a clean bowl (not included) (Fig. 14) with a paint brush (not included).

4. Turn the gas supply on at the LP gas cylinder.

5. Use the paint brush to apply the solution on the connection points on the LP gas cylinder and the regulator hose assembly (D) (Fig. 15).

6. Visually inspect for streams of bubbles coming from the connection points. This indicates that there is gas escaping.
   If no gas bubbles appear at any connections, the connections are secure.
   Ifa leak appears, repeat connecting the cylinder valve of the regulator hose assembly (D) to the valve outlet of the LP gas cylinder. Perform a gas leak test after reconnection to ensure a secure and leak-free connection.
   Ifaleak continues to appear after reconnection, do not use the appliance. Have the LP gas cylinder checked immediately by a liquid propane supplier.

7.  Wipe the LP gas cylinder and the regulator hose assembly (D) dry with a soft cloth.

Operation

Warning Risk of injury

• Only use the appliance when it is completely assembled, with all parts securely fastened and tightened.
• Always use the appliance on a stable and level ground.
• Always inspect the appliance for gas leaks, obstructions on the burner (B) and for any abrasion or wear.
• Keep the appliance away from high wind areas but keep it in a well-ventilated area.

CAUTION Risk of burns

The appliance becomes very hot while in use.
Use heat-resistant gloves, long-handled tongs or insulated mitts at all times.

8.1 Checklist before lighting

1. Read the instruction manual to understand correct operation and precautions.

2. Check that all components are properly assembled, intact and operable.

3. Visually inspect the appliance for any signs of blockage (debris, insects) on the burner (Bl or in the burner portholes.

4. A suitable LP gas cylinder is used (refer to chapter
   5.3 Picking a suitable LP gas cylinder).

5. Make sure that the top of the LP gas cylinder is dear of debris. Be sure any parts removed during assembly or servicing are replaced and fastened prior to starting.

6. No alterations have been made to the appliance.

7. LP gas cylinder is connected correctly (refer to chapter
   6.1 Connecting an LP gas cylinder).

8. Connections of the appliance and the LP gas cylinder checked for gas leaks (refer to chapter 7. Gas Leak Test).

9. Location of the appliance is suitable (refer to chapter
   5.1 Choosing a suitable location).

Warning Risk of injury
Never use wet fire glass (5) in the appliance. Wet glass can explode or fly out of the appliance.
Fire glass remain hot for some time after use. Let them cool down for at least 30 minutes before removing from the appliance.

1. Push in the control knob (F) and turn it clockwise to OFF position (Fig. 9).

2. Place enough fire glass {Tl on the tabletop {A) to cover the burner (B) (Fig. 16).
   NOTICE
   Do not block the vents on the top of the blowou box (C) with the fire glass (T).

3. Connect the cylinder valve of the regulator hose assembly (D) to the valve outlet of an LP gas cylinder {refer to chapter 6.1 Connecting an LP gas cylinder).

4. Turn the gas supply on at the LP gas cylinder.

5. Push in the control knob (F) and turn it counter-clockwise to LOW position.

6. Press and hold the electronic ignition (El to light the burner (B).

7. Release the control knob (F). Look for flames to ensure the burner (B) is lit.
   NOTICE
   If ignition does not occur in 15 seconds, turn the control knob (Fl to OFF position. Wait 5 minutes to allow any accumulated gas to dissipate before attempting to relight the burner (B)

8. After the burner (B) is lit, adjust the temperature setting as desired using the control knob (F).

8.3 After use

1. Push in the control knob (F) and turn it clockwise to OFF position.
2. Turn the gas supply off at the LP gas cylinder.
3. Disconnect the regulator hose assembly (D) from the LP gas cylinder.
4. When not in use cover the tabletop (A) with the lid (L) (Fig. 17).
5. When the product has cooled down cover it using protective vinyl cover (U).

8.4 Flame pattern
NOTICE
After lighting, perform periodic and visual checks of the burner flames.
A correct flame should be primarily blue with a yellow tip (Fig. 18).
An incorrect flame is excessively yellow, orange or irregular (Fig. 18). 1f this is the case, clean the burner {B) and burner portholes to increase airflow.

Cleaning and Maintenance

Warning Risk of injury!
Repair and maintenance should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners, and circulating air passageways of the appliance are kept clean.

9.1 Cleaning

WARNING Risk of injury!
Before cleaning or maintenance, set the control knob (F) to OFF position and allow the appliance to cool down. Turn the gas supply off at the LP gas cylinder and disconnect the LP gas cylinder prior to cleaning.
Clean the appliance regularly to prevent excessive flare­ ups.

Specifications

(LR03, alkaline)
Fire pit size| 30(76.2 cm)
Cylinder connection type| Type 1-QCC
Net weight| approx. 68.2 lbs (31 kg)
Dimensions (W x DH)| approx. 29.9 x 29.9 x 24.8″ (76x 76 x63 cm)

Frequently Asked Questions

one or have it refilled by a liquid propane supplier.
Turn the gas supply on at the LP gas cylinder before lighting.
Air in the regulator hose assembly. For first time use or if the appliance was not used for a longer period, it might take several lighting attempts to purge the air from the hose.
The regulator hose assembly is kinked. Straighten the hose.
The burner blows out.| Set the control knob to a higher setting.
Set the control knob to OFF position and turn the gas supply off at the LP gas cylinder. Let the appliance cool down and move it away from high winds.
Check if there is any sign of blockage (debris, insects) on the burner tube or in the burner portholes. Clean and unclog the parts properly.
The regulator hose assembly is kinked. Straighten the hose.
There are frequent flare­ ups.| Set the control knob to a lower setting.
Check if there is any sign of blockage (debris, insects) on the burner or in the burner portholes. Clean and
unclog the parts properly.
There is sign of gas leakage.| Turn the gas supply off at the LP gas cylinder and set the control knob to OFF position. Reconnect the
regulator hose assembly to the LP gas cylinder. Perform gas leak test to ensure leak-free connection.
Change the LP gas cylinder if corroded, rusted or damaged.
The regulator hose assembly is damaged. Contact a professional repair center for repair or replacement.
Burner flames are yellow or orange.| The LP gas cylinder is empty. Change it with a new one or have it refilled by a liquid propane supplier.
Check if there is any sign of blockage (debris, insects) on the burner tube or in the burner portholes. Clean
and unclog the parts properly.
Smell gas or a “rotten egg”
odor.| Propane suppliers add a distinctive “rotten egg” odor to propane because it is odorless. If user smells gas or
this odor, turn the gas supply off at the LP gas cylinder. Disconnect the cylinder valve of the regulator hose
assembly from the valve outlet of an LP gas cylinder. If the odor remains, call the fire department immediately as there is a risk that the LP gas cylinder is not properly sealed and is leaking. Do not try to fix the leaking LP gas cylinder yourself.

Disposal

Dispose of the appliance according to local regulations. If in doubt, consult your local authorities.

Battery Disposal

Do not dispose of used batteries with your household waste. Take them to an appropriate disposal/collection site.
To learn more about recycling batteries, visit: call2recycle.org/what- can-i-recycle

Feedback and Help

We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.
Scan QR Code below with your phone camera or QR reader:
If you need help with your Amazon Basics product, please use the website or number below.

https://www.amazon.com/review/review-your-purchases/listing/?ref=HPB_UM_CR

amazon.com/gp/help/customer/contact-us
+1877-485-0385

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>