Willtok 12PCS Premium Adhesive Hooks Instruction Manual

Failure to follow instructions carefully may cause damage
Save instructions or feel free to contact us

REPLACEMENT

WARRANTY
Our guarantee ensures quality for a full year!
Our product boasts a strong and durable body made from high-grade stainless steel, PVC, and PS materials.
This makes it resistant to water, oil, and rust, S0 you can enjoy its long- lasting performance.

APPLY

1. Clean the surface. Use rubbing alcohol to clean the surface where you will be applying the adhesive. Avoid using household cleaners, as they can weaken the adhesive.

2. Remove the protective film. Carefully remove the protective film from the back of the hook without touching the adhesive. If the temperature is below 10°C (50°F), warm up the adhesive with a hair dryer or heat gun.

3. Press firmly. Press the hook firmly in place for 10 seconds. Then, gently squeeze any bubbles from the center to the edges to remove them.

4. Wait 24 hours. Before hanging any items, wait 24 hours for the adhesive to fully cure.
   Test the hook. After 24 hours, gently pull down on the hook to test its security.
   If it feels secure, you can hang your object.

5. Tips for Apply:
   1. For best results, clean the surface with rubbing alcohol before applying the adhesive.
   2. If the temperature is below 10°C (50°F), warm up the adhesive with a hair dryer or heat gun before applying it.
   3. Press the hook firmly in place for 10 seconds to ensure a good bond.
   4. Wait 24 hours for the adhesive to fully cure before hanging any items.
   5. Gently pull down on the hook after 24 hours to test its security.

REMOVE

1. Soften the adhesive. Use a hair dryer or heat gun to soften the adhesive. Be careful not to overheat the adhesive, as this could damage the surface.

2. Remove the adhesive. Once  the adhesive has softened, use a plastic scraper or putty knife to carefully remove it from the surface. Be sure to remove all of the adhesive, as any residue could leave a mark.

3. Dispose of the adhesive properly.
   Dispose of the adhesive in a way that is safe for the environment. You can usually recycle adhesive tape or put it in the trash.

4. Replace the hook. if the hook is still in good condition, you can replace it with a new one. Be sure to clean the surface before applying the new hook.

5. Tips On Remove
   – For best results, soften the adhesive for a few minutes before removing it.
   – Be careful not to overheat the adhesive, as this could damage the surface.
   – Remove all of the adhesive, as any residue could leave a mark.
   – Dispose of the adhesive properly.
   – Replace the hook with a new one if needed.

DOS AND DON’TS

Applicable surfaces to use (must be flat/ceiling/siding):
Ceramic tile, marble, glass, stainless steel, wood, metal, plastic, laminate, refrigerators, washing machines…

Unsuitable surfaces to use:
Painted wall, wallpaper, poor wall surface, and rough surfaces, etc.
Once attached to the surface, the wall may get damaged.

CAUTION:
Keep away from small children. The thin film may cling to nose and mouth and prevent breathing.
Do not hand over beds or on walipaper.
Do not hang valuable or irreplaceable items.
Do not stick on valuable surface to avoid damage due to strong adhesive.

Limited Warranty and Limitation of Liability (for products sold in the USA)
This product will be free from manufacturing defects. If defective. your exclusive remedy shall be, at willtok’s option, product replacement or refund. Willtok will not be liable for any loss or damage arising from this product. whether direct. indirect, special,  incidental, or consequential.

MADE IN CHINA

Documents / Resources

| Willtok 12PCS Premium Adhesive Hooks [pdf] Instruction Manual
12PCS Premium Adhesive Hooks, 12PCS, Premium Adhesive Hooks, Adhesive Hooks, Hooks
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>