MAXDORIA B1N-DUAILSL 3 in 1 Wireless Lavalier Microphone User Manual

Wireless Microphone
User Manual

B1N-DUAILSL 3 in 1 Wireless Lavalier Microphone

3-in-1 multi-function receiver
Live Streaming I Video Recording I Interview I Vlog

Introduction

Thanks for choosing our product.
This product is a smart wireless microphone that provides professional­ grade recording output. Plug and play, no app required. It can be used in different scenes such as Live Streaming, Video Recording, Online Teaching and others.
The wireless microphone consists of three components: two microphone transmitters and a 3-in-1 multi-function receiver. (see as below pictures)

ID Diagram

1 windproof sponge
2 indicator light of microphone
3 Type-c charging port of microphone
4 Microphone clip
5 Power button of microphone
6 Reset key of microphone
7 Type-C receiver| 8 3.5 mm receiver
9 Lightning receiver
10 indicator light of receiver
11 Power button of receiver
12 Type-C charging port of receiver”
13 3.5mm audio transfer interface
---|---

The function of above will be specifically explained later.

How to use Lightning/Type-C receiver

First: Plug the Lightning or Type-C receiver into the Lightning or Type-C port of mobile phone, the green light of receiver flashes quickly.

Second: Single press the power button of mic, it is turned on successfully when green light is on. Last: Green light of receiver always stays on, and then the microphone works when opening phone camera to make a video recording or opening live streaming Apps to make a Live show.

Special Notes:
For the number @, if the mobile phone is in low battery during live streaming, the external power supply directly charges the mobile phone through the Type-C port of the receiver.

How to use 3.5mm receiver

Step 1: Insert the 3.5mm receiver into the corresponding port of the device, then press the power button on the receiver. Once done, the green light will start flashing.

Step 2: Press the power button of the microphone to turn it on, and the green light will start flash. Then the microphone will automatically pair with the receiver, and the green light will stay on to indicate a successful pairing. Step 3 : Turn on the device, the microphone will work directly.

About UI

Microphone Transmitter

once fully-charged
Search for pairing| /| Green light flashes slowly
Paired| /| Green light always on
Low battery alarm| Battery < 20%| Blue light flashes slowly
Stop| Single press| Blue light always on
Clear pairing| Press reset key quickly twice| Green light flashes quickly

Lightning Receiver

“beep”: minimum volume Two”beep”: medium volume Three “beep”: maximum volume
Noise reduction
switch| Press power button once| Turn off noise reduction: Red light on Turn on noise reduction : Green light on

Type-C Receiver

“beep”: minimum volume Two”beep”: medium volume Three “beep”: maximum volume
Noise reduction switch| Press power button once| Turn off noise reduction: Red light on Turn on noise reduction : Green light on

3.5mm Receiver

Green light flashes quickly
Monitor volume up and down, loop control| Double press the power button| One “beep”: minimum volume Two”beep”: medium volume Three “beep”: maximum volume
Noise reduction switch| Press power button once| Turn off noise reduction: Red light on Turn on noise reduction : Green light on

Note:

1. Clear the pairing /factory reset operation steps: with the mic in the power-on state, use a needle to quickly tap the side hole of the mic (TX) twice. when the green light flashes quickly, short press the button on the 3-in-1 receiver or  turn on a phone in 10s and quickly press the power button three times, the green light will flash quickly After waiting for about 10s, the mic and receiver will automatically be successfully connected, and the green light will stay on,  indicating a successful pairing Repeat these steps for both 2 mics and the 3-in-1 receiver
2. During recording or live streaming, you can listen to the video or recording through the single wired earphone. You can listen to the video or recording only after the receiver is unplugged from the device
3. The microphone can be used normally during the charging process. when in a connected state, the charging indicator flashes alternately between red and orange
4. For certain models of Android phones, such as Opto, Vivo, and OnePlus, there maybe additional steps required to enable certain functions
   Step 1: If your phone has toga (On-The-Go) function, you may need to manually turn it on. This can usually be done by going to Settings > Additional Settings> OTG, and toggling the switch to turn it on
   Step 2: Some models of Android phones may require manual setup to enable certain features For example, to use an external microphone for recording audio, you may need to go to Settings > Sound & Vibration > Other settings >
   Default Recorder >Use Peripheral Device

Packing list

(1) Microphone transmitter (Dual-Channel Version with 2 pCs)
(2) 3-in-1 multi-function receiver
(3) Type-C charging cable (Dual-Channel Version with 2 pcs)
(4) User manual
(5) 3.5mm TRS TO TRRS patch cable
(6) 3.5mm single wired earphone
(7) Carrying bag
If you have any questions, please contact us through our Email: info@maxtop.asia

MADE IN CHINA

Documents / Resources

| MAXDORIA B1N-DUAILSL 3 in 1 Wireless Lavalier Microphone [pdf] User Manual
B1N-DUAILSL, B1N-DUAILSL 3 in 1 Wireless Lavalier Microphone, 3 in 1 Wireless Lavalier Microphone, Wireless Lavalier Microphone, Lavalier Microphone, Microphone
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>