Lucci decor 011466 Create II Finishing Kit Instruction Manual
- June 4, 2024
- Lucci decor
Table of Contents
Lucci decor 011466 Create II Finishing Kit
CREATE II FINISHING KIT
SKU# 011466, 011467, 011468, 011469, 011470
NOTE: This instruction manual is the installation directions for the finishing
kit only. The suspension cord is sold separately, refer to the instruction
manual included with the suspension cord for installation directions.
Thank you for purchasing this quality Lucci product. To ensure correct
function and safety, please read and follow all instructions carefully before
assembly, installation, and use of this product. Please keep instructions for
future reference.
Warranty
- This product is covered by a 12-month warranty. The warranty is from date of purchase, not the date of installation.
- Please retain the proof of purchase for any warranty enquiries.
- Warranty will be void if there is any damage due to improper usage or modification to the product.
- Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.
Installation Instructions
Installation Requirements
- This installation instruction is for the finishing kit only. No electrical wiring connection or disconnection is required for installation of the finishing kit. The service of a licensed electrician is not required.
- The suspension cord (sold separately) must be assembled and installed by a licensed electrician.
- Lay out all the components on a smooth, non-scratch surface and make sure no components are missing before assembling.
- If parts are missing, return the complete product to the place of purchase for inspection or replacement.
- Check whether the product has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
- Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.
Installation Directions
NOTE: Ensure power to the luminaire (sold separately) you are working on
has been switched OFF before commencing the installation.
INSTALLING FINISHING KIT WITHOUT A SHADE:
- Install the Canopy Cover (A – Included with the Finishing Kit) by inserting the Lamp Holder (B – Included with the Luminaire, sold separately) through the hole and lifting up the canopy cover to the ceiling to magnetically attach to the Canopy (E). Note: make sure the decorative suspension ring (F) is positioned correctly in the central hole of the Canopy Cover. (Fig. 1)
- Install Lamp Holder Cover (C – Included with the Finishing Kit) by threading this onto the Lamp holder (B – Included with the Luminaire, sold separately) (Fig. 2 on page 3)
- (Optional) the Lamp Shade ring (D – Included with the Finishing Kit) can also be threaded onto to the Lamp Holder (B – Included with the Luminaire, sold separately) (Fig. 3 & Fig. 4 on page 3)
- Install a globe (G – not included) into the lamp holder (B – included with the luminaire, sold separately). Do not exceed the maximum wattage rating of the luminaire.
- Check and ensure the product is fully assembled, and all parts are secure before turning on the power. Switch the power ON to test and enjoy your new lighting product.
INSTALLING FINISHING KIT WITH A SHADE (SOLD SEPARATELY):
-
Install the canopy cover (A – included with the finishing kit) by inserting the lamp holder (B – included with the luminaire, sold separately) through the hole and lifting up the canopy cover to the ceiling to magnetically attach to the canopy (E). Note: make sure the decorative suspension ring (F) is positioned correctly in the central hole of the canopy cover. (Fig. 5)
-
To install with the lamp holder (B – included with the luminaire, sold separately) above the shade (Figure 6 on Page 5):
-
Install lamp holder cover (C – included with the finishing kit) by threading it over the lamp holder (B – included with the luminaire, sold separately) leaving enough of the lamp holder exposed to attach the following items. NOTE: ensure the threading within the lamp holder cover is at the bottom.
-
Attach the shade (H – sold separately) and secure it in place by treading the lamp shade ring
(D – included with the finishing kit) onto the lamp holder (B – included with the luminaire, sold separately)
To install with the lamp holder (B – included with the luminaire, sold separately) hidden within the shade (Figure 7 on Page 5): -
Install lamp shade ring (D – included with the finishing kit) by threading it over the lamp holder
(B – included with the luminaire, sold separately) and onto the upper threading (I). -
Attach the shade (H – sold separately) and secure it in place by treading the lamp holder cover (C – included with the finishing kit) onto the lamp holder (B – included with the luminaire, sold separately) NOTE: ensure the threading within the lamp holder cover is at the top.
-
-
Install a globe (G – not included) into the lamp holder (B – included with the luminaire, sold separately). Do not exceed the maximum wattage rating of the luminaire.
-
Check and ensure the product is fully assembled, and all parts are secure before turning on the power. Switch the power ON to test and enjoy your new lighting product.
Safety Tips
- Always ensure the power is OFF and the product has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the product.
- To avoid injury or damage to the product, ensure that power leads and screws are secure before connecting the power.
- Select a suitable location away from liquids and hazards.
- To clean wipe with a soft damp cloth. Do NOT soak or immerse the luminaire or product in water or other liquids.
- Ensure that the product does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
Specifications
SKU #| 011466| 011467| 011468| 011469| 011470
Colour| Textured
Black| Textured
Chalk| Brushed
Nickel| Aged Brass
Finish| Bronze
Finish
Finishing Kit Weight| 0.3 kg
Canopy Dimensions| H:38mm Dia:100mm
Lamp Holder Cover
Dimensions| H:85mm Dia:45mm
Lamp Shade Ring
Dimensions| H:10mm Dia:45mm
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>