Studiomaster MINI 6 Channel Karaoke Mixer Instruction Manual
- June 14, 2024
- Studiomaster
Table of Contents
Studiomaster MINI 6 Channel Karaoke Mixer
lntrodudion
Thank yau far buying the Studiamaster Professianal MINI series Mixer. To ensure maximum performance and safety, please Fallaw this instruction manual carefully. Please retain this manual far future reference. For any complaint, feedback or testimonials please contact our distributor/dealer. Retain the cartons for future use should the product require servicing/maintenance.
Features at a Glance
- Gain control with 2band EQ per channel.
- Built-in echo/delay processor with unique e- delay.
- MP3 music player with USB & Bluetooth.
- Clip LED indication per channel.
- Signal & clip LED indication for master level.
- 1/4 TS Unbalanced L/R main output.
Input Sedion
The input sections of the MINI series mixer have two connectors far ¼”MIC & Jack inputs.? Please do not use both the inputs at the same time_ Doing this may permanently damage the mixer.
-
MIC Inputs : This electrically balanced jack input(¼” stereo (TRS) jack) is designed to accept low impedance balanced signals from microphones.
-
Line Inputs: The line input will accept line level balanced signal using ¼” stereo (TRS) Jack. The line input is designed far instruments like Keyboards, Guitars, Drum Machines & other electronic instruments.
Note: Both above jacks can accept unbalanced input also with quasi- balanced cable (pin 2-signal, pin 1 & 3 shorted-GND) -
Gain Control: This knob is used to control gains of both MIC & Line input signals.􀀓 Please do not operate ot high goin levels os this distorts the signal & leads to audio clipping.
-
EQ Section: The MINI series has 2 Band Equalizer .The EQ is designed to be easy yet effective to use. It can be used to cut or boost certain frequencies to achieve a particular tone, or to eliminate any unpleasant characteristics.
- HF Control: The HF control can be used to cut or boost up to+/- 15dB at lOkHz. Tip: This frequency band can be used to brighten up high frequencies.
- LF Control: The LF control can be used to cut or boost up to+/- 15dB at lOOHz Tip: This frequency band can be used to get a punchy bass response.
-
EFX: This knob is used to control the send level to the built in EFX section.
-
Channel control: This control is used to set the level going to the master output.
-
Clip LED: This clip LED glows when the incoming audio signal is clipping. Please reduce gain levels to avoid distortion of clip Led is glowing.
-
Stereo i/p:
- Stereo INPUT/MONO : It is Unbalanced 1/4″ Mono jack input suitable for high impedance sources. This input may also be used as mono line input by plugging into the left/mono socket only.
- RIGHT: It is same as for left channel above except input fed to this channel is routed to right channel only.
-
Master (L/R) Output: This output is used to connect the master output of the mixer to the amplifier or powered speakers using ¼”TS Unbalanced jack connector. The output level is determined by the master control. Wiring configuration is as follows :
-
Power LED: This Blue LED Indicates that unit is powered ON.
-
Signal/Peak LED: Signal LED(green) glows when output is below clip level. Clip LED glows when the output signal is clipping.L’.h Please reduce avoid distortion clip led is glowing. levels to reduce clipping.
-
Master (L/R) Control : The Left & Right Control are the master output level control. They determine the level of all signals going to output connector.
-
Delay Time Control: This control adjusts the delay time. Turning the knob clock wise, will make the delay time longer.
-
Repeat Control: This control adjusts the feedback amount [the number of repetition for the delay sound (echo)]. Turning the knob clock wise increases the number of repetition. As you turn up the repeat knob clock wise, oscillations may occur. If this happens, turn the knob down until the oscillation stops.
-
EFX Level Control: To Control the output level of Effect signal.
-
Effect ON/OFF Switch: To switch ON/OFF the Effects.
-
EFX ON LED : This LED glass when EFX is selected.
Media Player Sedion -
USB Input : USB input channel
Terms of use : Studiomaster Professional respects intellectual property rights and we request our users to do the same. Please use Mp3 downloads only for program which you have legally purchased.
PLEASE DO NOT USE PIRATED MUSIC OR PROGRAM. -
Display: The seven segment display is provided to visualize all media player operation.
-
On-Off/Mode Selection:
- Long press to switch On/Off the media player.
- USB is default mode.
- Single pressing will switch USB and Bluetooth mode (BT).
-
Next/Nol+:
-
Single press this switch to go next track.
-
Long press will increase volume of media player.
-
Prev.Nol-:
- Single pressing the switch will go to previous track.
- Long pressing the switch decrease the volume of media player.
-
Play/Pause/Repeat:
- Single press will switch media player between play and pause state.
- Long pressing this switch will change repeat selection from single track to all track.
-
IR Sensor: The IR sensor is provided for remote operation.
-
Gain Control: This knob is used to adjust media player.
Remote Features:**** -
Mute: Press the switch to mute the audio track.
-
EQ: Press the switch to select below effects to the audio track.
- Jazz (JAZ)
- Pop (POP)
- Classic (CLA)
- Rock (rOC)
- Normal (Nor)
- Cut (Cut) – Bypass low frequencies
-
U/SD: Not Active.
-
0-9: Press switches to directly play track within the library.
Note: Remote control range is about it 6-8 meters insight (Please insure that the remote batteries are fully charged).
BLOCK DIAGRAM
Technical Specifications
Product Care Instructions
- Do not drop the mixer; this could severely damage the products.
- Please keep this product away from direct sunshine & rain.
- Please keep this product away from heavy magnetic or electromagnetic fields, it could affect the product performance.
- Please disconnect from power supply when the product is not being used for a long time.
- Do not open any of the components yourself, for repairs please get in touch with your Studiomaster dealer.
- It is recommended to place product in flight case while transportation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>