Flysums TD1 Cordless Vacuum Cleaner User Manual

**Flysums TD1 Cordless Vacuum Cleaner User Manual

**

SAFETY WARNING

IMPORTANT SAFETY INSTRUCTIONS

When using an basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

DAMAGE, OR INJURY:

1. To protect against electrical shock, do not immerse the power cord or plug in water or any other liquid. Please always operate it with dry hands to avoid the risk of electrical shock or serious personal injury.
2. Close supervision is necessary when any appliance is used by or near children. This vacuum is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and common sense unless they are supervised or have been given instructions on using the vacuum by a person responsible for their safety.
3. Do not use the vacuum outdoors. It is for household use only.
4. Do not use the vacuum if it has been dropped, damaged, left outdoors, or dropped in water. Please contact customer service for help when the appliance or the adapter is damaged.
5. Use the vacuum only as described in this manual. The use of accessory attachments not recommended may cause damage to the vacuum or personal injuries.
6. Do not use abrasive materials to clean the vacuum. Do not use spirits or other solvents to clean the appliance.
7. Do not use the appliance to vacuum any of the items below:
   • Water, flammable, or combustible liquids such as gasoline.
   • Lighted stubs, matches, hot ashes, or other combustible items.
   • Needles, pins, or other sharp items.
   • Wood pieces, gesso, cement, calcimine, or other tiny granules.
   • Pieces of string or fabric.
8. Do not pick up liquids with the vacuum or use it on wet floors. Do not immerse the vacuum in water.
9. Do not use the vacuum on concrete, tar, or similar rough surfaces.
10. Do not vacuum frayed carpets or carpet tassels.
11. Do not use the vacuum without the dust cup lid in place.
12. Do not put any objects into openings of the vacuum. Do not use when any openings are blocked. Keep free of dust, lint, hair, or anything that may reduce air flow.
13. Keep hair, loose clothing, fingers, and all body parts away from openings and moving parts.
14. Store the vacuum indoors. Store after use to prevent accidents.
15. Keep the vacuum cleaner away from stoves and heat-emitting appliances. Heat can deform and discolor the plastic parts of the unit. Please use the vacuum at the temperatures between 32ºF-104ºF.
16. Always remove the adapter from the power socket when the appliance is not being charged.
17. Unplug charging cord from the appliance and power it off before cleaning or performing maintenance, making tool adjustments, changing accessories, orstoring, to avoid powering it on accidentally.
18. The battery must be removed from the appliance before disposing of it.
19. The battery must be disposed of safely.
20. The appliance includes Li-ion batteries. Do not incinerate the batteries or expose them to high temperatures, as they may explode.
21. The thermal cutout will switch off the vacuum automatically when it overheats. If this happens, turn off the power switch, and wait for 45 minutes to restart the vacuum.
22. Use only the adapter provided by the manufacturer.

• Keep the adapter away from liquids.

• Do not vacuum large pieces of paper.

• Do not vacuum flames or flammable substances.

• Do not vacuum water or liquids

• Do not remove the plug by grasping the cord.

WHAT’S IN THE BOX

CAUTION:

Assemble the vacuum according to the “ Assembly ” section.

• Vacuum Main Body

• Electric Floor Brush/

• Adapter

• Extension Rod

• 2-in-1 Crevice Tool

• Wall Hanger

• Screws and Wall Anchors

OVERVIEW

ASSEMBLY

SPECIFICATION

Name: Vacuum Cleaner
Model: TD1
Adapter Input Voltage: 100-240V 50/60Hz
Adapter Output Voltage: 31V

Environmental Protection Instructions:

The chemical substances contained in the built-in lithium-ion battery of this product will pollute the environment. Before discarding the product, the battery must be removed and handed over to a professional waste battery recycling station for disposal.
Do not dispose of old appliances with household waste.
Before disposing of your old machine, remove the dust cup and dust cup filter assembly, which can be disposed of with normal household waste.

Notice:

1. When removing the battery, please make sure that the power is exhausted and operate with the adapter disconnected.
2. Be careful not to make the positive and negative electrodes touch when unplugging the connector, so as not to cause a short circuit.
3. Please disassemble the entire battery pack at the same time, so as not to damage the shell of the battery pack, cause a short circuit or cause leakage of dangerous substances.
4. If you accidentally come into contact with battery leakage, please rinse with clean water and seek medical attention.

OPERATING INSTRUCTIONS\

• Charging Instruction

CAUTION

• The battery must be fully charged before the first usageas the product is delivered non fully charged for safety.
• Please use the original charger(31V).lt takes about4-5 hours to fully charge the battery.
• The vacuum cannot be turned on when charging for safety.

Description of Charging Indicator:

When charging, plug the adapter into the AC power socket, and plug the DC connector of the adapter charging output cable into the charging interface of the battery pack to charge the vacuum cleaner.

When the machine is in the charging state, the vacuum cleaner atmosphere light (blue light) lights up, and the battery indicator light jumps in turn, indicating that the vacuum cleaner is in the charging state, and the vacuum cleaner atmosphere light (blue light) automatically turns off after 1 minute of charging; when the power indicator light is fully on, When it stops flashing, it means the vacuum cleaner is fully charged.

Do not leave the vacuum cleaner in a state of low power for a long time, please pay attention to using the original charger of this product to charge.

• Battery Pack Disassembly And Assembly

Press and hold the release button on the top of the battery pack while holding the battery pack and take it out.

• On-Screen Indicator Description

Button Description

1. Press Switch Button : Vacuum cleaner starts to run, and the vacuum cleaner works at the 80 gear by default. When vacuum cleaner is working at any gear, just press the switch button again, and vacuum cleaner will stop running.

2. Press Speed Control Button : The working speed of vacuum cleaner, that is the suction power of vacuum cleaner, has 5 gears, which are 0 gear, 40 gear, 80 gear, 120 gear, and 150 gear. 40 gears, 80 gears, and 120 gears can be switched by the speed control button.
   The 0 gear is the OFF gear, and the 150 gear is the AUTO gear. The AUTO gear is realized by automatic adjustment of the smoothness of the air duct sensed by vacuum cleaner.When vacuum cleaner encounters a relatively serious air duct blockage, the suction blockage indicator will flash, and vacuum cleaner will automatically switch to the AUTO gear, which will instantly increase the suction power of vacuum cleaner and remove the blockage. If the blockage is removed after 7 seconds, vacuum cleaner returns to the original working gear to run.

3. Light Control Button : Can control the LED lighting on and off. Press the light control button, the light on the brush head of the vacuum cleaner will light up, and press it again to turn off the LED light.

Description of Display

1. Display of Remaining Working Time : After starting up, the display will automatically display the remaining working time of vacuum cleaner in minutes. Within 1-2 seconds after turning on the vacuum, the time display will fluctuate, because the CPU of vacuum cleaner is calculating and verifying the remaining working time. Due to changes in the environment and temperature of the vacuum cleaner, there will be a slight deviation between the remaining working time display and the actual display time during use, which is normal. When the power of battery is low The time display will blink, indicating that the battery is low and needs to be charged immediately.

2. Battery Power Display : The 4 squares on the power display represent the remaining power. 1 grid represents 25% power, 2 grid is 50% power, 3 grid is 75% power, 4 grid is 100% power. When charging, the 4 squares of the power display will flash one by one. When the power indicator stops flashing, it means it is fully charged. When working, the 4  squares of the power display will disappear in turn. When the bottom square is flashing, it means that the battery is low, and the vacuum cleaner needs to be charged as soon as possible.

3. LED Lighting Indicator : When the LED lighting indicator is on, it means that the LED lighting of vacuum cleaner is working.

4. Ambience Light Indicator : When the ambience light indicator is on, it means the ambient light of the vacuum cleaner is working.

5. Brushroll Jam Indicator : It is necessary to clean the brush roller, remove blockages or adjust the contact between the floor brush and the ground to avoid rugs, towels or bed sheets getting caught in the floor brush air intake.

6. Suction Blockage Indicator : When the suction blockage alarm indicator is on (red), it means that the air duct of vacuum cleaner is blocked, and it is necessary to check and clean the air duct of the vacuum cleaner:
   Please check whether the extension rod and the air inlet of the main body of vacuum cleaner are blocked, and whether the filter in the main body needs to be cleaned, etc.

7. Vacuum Cleaner State Indicator : 0 gear means vacuum cleaner is OFF. 40 gear means low working state. 80 gear means mid-range working state. 120 gear means high working state. And 150 gear is the AUTO-state.
   The gears (0, 40, 80, 120, 150) are related to the speed of vacuum cleaner’s motor, which represents the state of the motor’s speed. The data is larger, the speed of motor is higher.

• 2-in-1 Crevice Tool Instruction

Press and hold the button while pushing and pulling forward. At this time, the brush can be used as a dusting brush to clean keyboards, curtains, etc.

Press and hold the button while pushing and pulling back. At this time, the brush can be used as a flat suction to clean the gap particles such as windows.

OPERATING INSTRUCTIONS

• Accessories Usage Guide

1. Floor Brush: suitable for carpets, floors, and other flat, horizontal surfaces

2. in-1 Brush: suitable for cleaning the dust or large particles in the gaps of doors, windows, keyboards, car interiors, etc.

• Wall Hanger Instruction

1. Insert wall anchors into the preinstalled holes of the wall, use two fixing screws to respectively pass through the two installation holes of the wall hanger. Align wall anchors, insert the fixing screw into wall anchors, and tighten the screw clockwise.

2. After the wall hanger is fixed, the vacuum main body is placed on the wall hanger as shown in the figure, and the accessories are inserted into the  accessory fixing holes on the side of the wall hanging to fix, as shown in the figure.

CLEANING AND MAINTENANCE

CAUTION:

Always switch the vacuum OFF before attempting to empty the dust cup

• Clean the Dust Cup

1. When the dust in the dust cup exceeds the MAX mark, please empty the dust cup in time, otherwise the suction may be weakened.

2. Remove the extension rod from the main body before maintaining and cleaning dust cup and HEPA filter.

3. Open the dust cup cover to dump the dust, and please close the dust cup cover after emptying the dust cup.

CAUTION :

If you find that the suction is weak or the “ Suction Blockage Indicator” on the LED screen flashes, then please wash the filter.

• Cleaning the Filter Device

1.   Press the dust cup release button and remove the dust cup

2. Lift the HEPA out of the dust cup

3. Clean the filter screen and filter cotton under water, Air dry them for at least 24 hours before using them again.

4. Assemble the filter screen and filter cotton back to the original position. Do not assemble them until completely dry.

CAUTION :

When “Brush roll Jam Indicator” flashes until the screen goes off and floor brush stops rotating, it means that the floor brush is blocked. Check the floor brush and clear the blockage.

• Clean the Floor Brush

1. Press the release button and hold to pull out to detach the rob from floor brush.

2. Turn the switch to the ” ” sign, rotate the catch upwards and remove the floor brush.

3. Use scissors to remove hair and strings that get wrapped around the roller brush.’

4. Install the roller into the floor brush and rotate the buckle down to complete the installation.

CAUTION :

Low suction or vacuum failure caused by overheating may be due to a clog in the vacuum. Please check and clear clogs in the dust cup, mesh shell, pre- motor filter, post-motor filter, metal tube, and floor brush.

• Cleaning a Clog

1. Check and empty the dust cup

2. Check and rinse the filter and sponge. Do not assemble them until completely dry.

3. Check and empty for clogs inside the extension rod

4. Check and clean tangles on roller brushes, remove with scissors.

TROUBLESHOOTING

the vacuum with the original adapter.
The battery pack/adapter malfunctions| Contact customer service for help.
The vacuum cannot be powered on| The battery runs out| Charge the vacuum with the original adapter.
The battery pack Is not attached correctly| Remove and reattach the battery pack and make sure It is securely attached In place.
Other malfunctions| Contact customer service for help.
The vacuum stops working Suddenly| The battery has drained| Use the original adapter for charging. It is recommended to charge the vacuum after each use, and use the low-suction mode for longer runtime.
The floor brush gets stuckbrush.| Clean foreign objects entangled on the floor
1.  The air duct Is blocked2.  The dust cup Is full| Clean the floor brush, tube, dust cup. and the sponge regularly.
Other malfunctions| Contact customer service for help.
The cleaning results are not satisfactory| Incorrect use of the vacuum|

1. Use the high suction mode for cleaning complicated environments.
2. Use the crevice tool for better pickup of heavy objects such as beans.
3. Use the floor brush for cleaning stains.

The battery runs out| Please charge the vacuum fully and try to turn it on again.

• The air duct Is blocked
• The dust cup is full

| Clean the floor brush, tube. dust cup and the sponge regularly.
The sponge is not completely dry| Detach and air dry the sponge completely. It Is recommended to clean and replace it regularly.
There is static during vacuuming| There is too much dust inside the dust cup| Empty the dust cup.
The vacuum runs with much static| It’s normal for there to be much static in the air in winter and in dry regions.
The electric floor brush stops working| The floor brush gets stuck| Clean foreign objects entangled on the floor brush.
Other malfunctions| Contact customer service for help.

WARRANTY

• CUSTOMER CARE

The 1-year Limited Warranty is valid for Products.

If your machine is used correctly according to the instruction manual and there is a quality failure during the warranty period, we will provide you with free warranty service once you contact us.

If service parts are no longer available or discontinued, they will be replaced with functional replacements.

• WHAT IS NOT COVERED

1. Under your machine guarantee, warranty shall not be liable for costs of repair or replacement of a product incurred as a result of:Accidental damage, faults caused by negligent use or care, misuse, neglect, careless operation or any handling of the appliance which is not in accordance with this Instruction Manual.
2. Machines purchased from an unauthorized dealer.
3. Use of parts and accessories other than those produced or recommended by unauthorized parties or agents.
4. Repairs or alterations carried out by unauthorized parties or agents.
5. Use of the machine other than for normal domestic purposes, e.g., for commercial or rental purposes.
6. Reduction in battery run time due to battery age or usage.

WARRANTY SERVICE

1. If you have a query about your fly sums appliance, please contact customer service at: support@flysums.com
2. Please inform us of your model name/number, purchased date, order number, machine malfunction details and your request for reparations.
3. Your model number can be found on the rating plate.
4. Please keep your purchase receipt in a safe place to ensure you have this information. Service rendered under this warranty will not extend the term of the warranty.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>