Allegra R1-1 One key RF Remote Controller User Manual
- June 14, 2024
- Allegra
Table of Contents
One-key RF Remote Controller
Model No.: R1-1
One-key portable dimmer/Wireless remote 30m distance/CR2032 battery/Magnet
stuck fix
Features
- Apply to single color LED controller.
- Each remote can match one or more receiver.
- CR 2032 attery powered.
- Operate with LED indicator light.
- Magnet on the back which can be easily stuck on any metal surfaces.
Technical Parameters
Input and Output
| Output signal | RF 2.4GHz) |
|---|---|
| Working voltage | 3VDC CR2032) |
| Working current | ＜5mA |
| Standby current | ＜2μA |
| Standby time | 2 years |
| Remote distance | 30m(Barrier-free space) |
Warranty
| Warranty | 5 years |
|---|
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
---|---
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED
Environment
| Operation temperature | Ta: -30° C ~ +55° C |
|---|---|
| IP rating | IP20 |
Mechanical Structures and Installations
To fix the remote, three options are offered for selection:
Option 1: stuck on any metal surfaces directly.
Option 2: fix it on the wall with two screws.
Option 3: adhere it to the wall with paster.
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered for selection:
Use the controller’s Match key
Match:
Short press match key, immediately press on/off key on the remote.
The LED indicator fast flash a few times means match is successful.
Delete:
Press and hold match key for 5s to delete all match,
The LED indicator fast flash a few times means all matched remotes were
deleted.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
Safety information
-
Read all instructions carefully before you begin this installation.
-
When installing battery, pay attention to the battery positive and negative polarity.
A long time without the remote control, remove the battery.
When remote distance becomes smaller and insensitive, replace the battery. -
If no response from the receiver, please re-match the remote.
-
Gently handle remote, beware of falling.
-
For indoor and dry location use only.
FCC Warning
15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 5mm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>