Luxchoice Plush Air Bed Blow with Built in Pump User Manual

Luxchoice Plush Air Bed Blow with Built-in Pump

WARNING

W A R N I N G : THIS PRODUCT IS NOT FLAME RESISTANT. THIS BED CONTAINS PLASTIC. DO NOT PLACE AIR BED NEAR OPEN FLAME OR OTHER SOURCE OF IGNITION.
W A R N I N G : This is not a toy. To avoid risk of fire, burns, injury or shock, it should not be played with or placed where children could reach out.

• Unplug adapter after inflating it.
• Pump is an electrical device. Do not use in or around water.
• Do not attempt to disassemble, repair, or service the pump.
  No serviceable parts are contained inside. Contact us for service or repair.

WARNING

• This is not a water toy or flotation device. Use as a bed only.
• It is not recommended for children under three year-old.
• This bed is not intended for infants or persons with limited mobility. They may roll off of the bed and become entrapped between the bed and walls and suffocate.
• Do not use this bed on abrasive surfaces or near pointed, sharp, or protruding objects. Bed may puncture. Remove all sharp objects from area the bed will be used in.
• Do not step or jump on bed, or use as a trampoline. Standing, jumping, or walking on the bed may result in injury or damage or puncture the bed.
•  Make sure the surface is clean of any debris, sharp objects, or protrusions and place bed in a safe area before use. Make sure that there are no sharp edges, steps, drops, or breakable items nearby. Use only on flat surfaces, as bed may tip over on uneven surfaces

SET UP GUIDE
Your Luxchoice air bed has a built-in air pump as well as a 2 Stage Valve. The 2 Stage Valve is used for inflation and deflation. This Valve is constructed in three parts:

1. Bleeder valve with valve lip
2.  Middle valve
3. Upper cap

INFLATION

1. Place your bed on a flat surface free of debris, obstructions and sharp  objects.
2.  Spread the bed out so that it can fill easily. Allowing the bed to”unfold” itself may place an unnecessary strain on the bed and the pump.
3. Make sure the Middle Valve ②and Upper Cap ③are closed.
4. Turn the inflate/deflate valve (B) on the built in pump to the inflate position to inflate the bed.
5.  Turn inflate/deflate valve to the off position once the desired firmness has been achieved.

OPTIONAL INFLATION PROCEDURE

This Luxchoice air bed comes with a secondary inflate/deflate option (A) for use with portable air pumps as a backup to the installed automatic pump. To use a portable air pump (does not include extra air pump), follow these instructions:

1. The middle valve ②must be pushed in tightly to the bleeder valve ①. The upper cap ③must be removed from the middle valve in order to inflate.
2. Ensure inflate/deflate valve (B) is in the off position.
3. Insert the portable pump into the middle valve ②.(Use proper pump adapter fitting if needed.)
4. Remove portable pump and switch off. (Middle valve ②has a built in stopper that will automatically close when pump is removed stopping any air loss.)
5. Replace the upper cap ③.

DEFLATION

1. Turn the inflate/deflate valve (B) to the deflate position to deflate be
2. Deflate until the bed is fully deflated. For faster deflation, you may open the middle valve ②.
3. Turn inflate/deflate valve to the off position to turn pump off.
4. Fold bed according to folding instructions below and place into carrying bag and store until next use.

FOLDING INSTRUCTIONS

1. Upon complete deflation, lay bed on flat surface with sleeping surface facing upwards and fold according to the steps below.

CARE AND MAINTENANCE

1. Inspect your bed before each use.
2. Keep your bed away from any sharp or protruding objects. Large cuts, tears, or snags may not be repairable and will not be covered by your warranty.
3. Repair patches have been included in case of incidental damage to your bed. Please follow repair instructions carefully.
4. When not in use, keep your bed in a clean, dry place out of . extreme temperatures.

CLEANING

1. DO NOT SUBMERGE MATTRESS IN WATER!
2. For spot cleaning, use a clean damp cloth to wipe the surface of themattress. Apply a clear liquid dish detergent without dye if necessary.
3. Wet stained area thoroughly; gently rub the stained area with detergent. Blot the area to remove the staining substance.
4. Rinse thoroughly and pat dry. Allow your bed to air dry completely after cleaning and before storing.

ADDITIONAL INFORMATION

IN CASE OF AIR LEAKAGE

Please check the following if there is an air leak.

1. 1s the inflate/deflate valve on built in pump turned to inflate position?
2. 1s the secondary inflate/deflate valve cap closed? Repair patches have been included for minor repairs.

REPAIRING AN AIR LEAK

1. Wipe bed with mild soap water over area to find possible air leak. DO NOT SUBMERGE MATTRESS IN WATER! If there is a leak bubbles will form around leakage area.
2. Follow cleaning instructions for leak area.
3. Use included patch kit, tear off the clear side of the patch and then press patch firmly over the puncture area.
4. Wait one hour before inflating

PLEASE NOTE
Stretching is a natural occurrence of new vinyl. During the first day of use, this air bed may become soft and require additional inflation to maintain desired firmness.

WARRANTY POLICY

Luxchoice Air Beds are warranted against defects in material and workmanship. We offered warranty. Problems covered by the warranty include failure of the pump, seams or the valve. Punctures or wear to the
bed due to use or abuse are not covered. It is normal for an airbed that has been inflated for extended periods to require the addition of air after a few days. Air will be lost from the bed through the material over time. Also, cooling of the air around the bed will cause the air inside the bed to contract, and the bed will be softer and may need refilling

CONTENTS

1.  Air mattress with built-in pump
2. Carrying bag
3. Repair patches

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>