DEKO TOOLS DKCSP03 Submersible Utility Water Pump Instruction Manual

DEKO TOOLS DKCSP03 Submersible Utility Water Pump

IMPORTANT: Read this instruction manual before operating this product. Keep the instruction manual for future reference.

General Tool Safety Warnings

Read all safety warnings and all instructions. Failure to follow all warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. For safety reasons, people who are not familiar with these operating instructions should not use this Submersible Pump.

Before Start-up, Note The Following!

Mains Supply

Your new submersible pump is equipped with a shock-proof plug according to regulations. the pump is designed to be connected to a 100-120V~50/60Hz (for final and correct voltage /frequency info, please refer to the rating label on the product) safety socket. Make sure that the socket is sufficiently secured and is in excellent condition. Introduce the plug into the socket and the pump is ready to go.

If the mains cable or plug suffers any damage from external action, repairs to the cable should be serviced by a qualified specialist using only standard spare parts. This will ensure that it meets the required safety standards.

• Always check the pump (above all power cable and plug) before each operation. A damaged pump must not be used. It is absolutely necessary to have the pump checked by your electrician.
• Take care that the electrical connections are made within a dry area, protected from flooding.
• Protect plug and power cable from heat, oil and sharp edges.
• Check line voltage. Data indicated on the type plate must match technical data the main supply.
• Children under the age are not allowed to operate the pump. Keep them away from the connected unit.
• Before use, first clear the outlet.
• Circulation of aggressive fluids,as well as the circulation of abrasive Materials Must Be avoided at all costs.
• The submersible motor-driven pump must be protected from frost.
• The pump has no self-stop function. In order to prevent the pump from running dry or other faults, it is necessary to ensure that the pump is kept in observation during operation.

Parts Description

1. Power cable
2. Handle
3. Output hose fitting ( GHT 3/4″, NPT 1-1/4″ From up to down)
4. Pump base
   

Specifications

1-1/4″(From Up to Down)
Max. Water Temperature| 95°F (35°C)| 95°F (35°C)
Waterproof Class| IPX8| IPX8

Remark: for final and correct voltage / frequency info, please refer to the rating label on the product.

Intended Use

This non-automatic submersible utility pump is designed to remove water from, flooded basements, window wells and stock tanks, etc.

Assembly

Hose Connection

The output hose fitting and adapter allows connection of GHT 3/4″, NPT 1-1/4″ hose (From Up to Down), depending on your  individual requirement or applications.

Remark: the coming fitting/adapter may vary according to different countries or markets. Please refer to the package, sales details or your dealer.

Installation

1. Install the pump on a hard level surface in the water. If necessary, placebricksoperation blocks under the pump to raise it off the bottom. Do not place the pump directly in mud, sand or silt or on rocky surfaces as these materials can clogo cause damage to the pump.
2. Connect a hose to the pump discharge. Use either the supplied garden hose adapter or other hose fitting (sold separately). Choose the best size hose or pipe for your application.
   NOTE: To keep friction loss as low as possible, do not use a hose that is smaller than 3/4″.

Operation

After having read these instructions carefully, you can set your pumptowork, reconsidering the following item:

• Check if the pump rests on the ground.
• Check if pressure cord has been attached properly.
• Check if the voltage/frequency of the receptible corresponds to that of the pump.
• Make sure that water and humidity can never come to the mains supply.
• Avoid pump running dry.

1. Connect the plug into a 100-120 volt AC grounded outlet. The use of a GFCl is strongly recommended.
2. After the power is connected, the water pump starts to run. After the power is disconnected, the water pump stops running.
3. Do not let the pump run dry. The pump depends on water for cooling and lubrication. Operating the pump without water may cause the motor to overheat or cause damage to internal parts. It may shorten the life of your pump. Pumping fluids above 95°F (35°C) also shortens the life of the pump.

Air Lock

When a pump airlocks, it runs but does not move any water. An airlock will cause the pump to overheat and fail. This pump has an air discharge hole to prevent airlock. If you suspect an airlock, unplug the pump, clean out the anti-airlock hole with a paper clip or piece of wire, and restart the pump.

Maintenance

Maintenance Guidelines

This submersible pump is an approved, maintenance-free high quality product, which is subject to severe final controls.

We recommend, regular inspection and maintenance to ensure long equipment life and uninterrupted operation.

Note:

• Remove the mains plug before all maintenance work.
• In the event that the pump is often transported in the course of operation, it should be cleaned out with clear water after every use.
• In case of stationary installation, the function of the locating switch should be checked every 3 months.
• All fibrous particles which may have built-up inside the pump housing should be removed with a water jet.
• Every 3 months the shaft ground and as should be cleaned from mud.
• Remove deposits on the floater with clear water.

Cleaning The Impeller

If excessive deposits collect in the pump case you must dismantle the bottom part of the pump as follows:

1. Remove the intake cage from the pump case.

2. Clean the impeller with clear water.
   WARNING: Do not put down or rest the pump on the impeller!

3. Assemble is reverse order

Trouble Shooting

• Pump is not plugged in, switch or breaker is off

|

• Plug pump in or turn on switch / breaker

• Check for blown fuses or tripped circuit breakers or tripped outlets

|

• Replace fuse, reset breaker, reset outlet

If the pump runs but moves little or no water| Clogged intake screen| Clean or replace screen
Clogged discharge hose/pipe| Remove clog
Impeller obstructed| Remove obstruction/debris
Frozen discharge hose/pipe| Allow hose/pipe to thaw
Pump is air locked| Clean out airlock hole with a paper clip or pipe cleaner
Low line voltage| Check wire size and increase if necessary
Worn, damaged or clogged pump parts| Inspect for wear, damage or clog and clean or replace if necessary

Guarantee Note

Not covered by guarantee:

• Destruction to rotating mechanical seal by dry running or impurities in water.
• Blockage of running wheel through foreign bodies
• Transport damage
• Damage caused by unauthorized persons

Service Information

This tool is warranted to the original purchaser to be free from defect in materials and workmanship for a period of 2 years from the original purchase date.
If the tool should fail some day in spite of our quality controls and materials, only have it repaired by an authorized electrician or contact your local distributor or service agent. Or you can contact us by emails:
services@dekotools.com,
support@dekotools.com
The warranty will not apply to the following cases:
(i) where this product has been subjected to misuse, abuse, accident or want of care;
(ii) where this product has been used for a purpose for which it was not designed or not suited;
(iii) where the service of this product has been undertaken by a non- authorised person or company or if non-approved parts have been used.
(iv) components that are subject to natural wear and tear caused by use in accordance with operating instructions.

Disposal

The machine and packaging should be sorted for environmental-friendly recycling. Do not dispose of power tools into household waste! Please Recycle Them at collection points provided for the purpose. Ask your local authority for information about recycling.

DEKO TOOLS CO., LIMITED
www.dekotools.com Made in China

References

• DEKO – DEKO Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>