ViGOSit JD01 Ergonomic Adjustable Gamer Computer Chair Instruction Manual
- June 14, 2024
- ViGOSit
Table of Contents
JD01 Ergonomic Adjustable
Gamer Computer Chair
Instruction Manual
PARTS CHECKING
Please check the parts before assembling
INSTRUCTION
If you have any questions during assembly, Please feel free to contact the after-sales service department vigositus@163.com
-
Installation of Base
1.Install the five feet of base to the core of base as shown.
Use five M6x20mm (a) screws to reinforce the joints of the base.
2.Turn the base over and insert the casters firmly as far as it will go. XTo prevent the casters from coming off,it is a bit difficult to insert.
-
Installation of Gas Cylinder
Insert the gas cylinder into the base as shown.
-
Installation of Tilt Mechanism
Place the seat on a stable place such as a table.
Using the four M8x20mm (c) screws to attach the Tilt Mechanism to the seat cushion. -
Installation of Footrest
Using the four M6x20mm (a) screws to attach two footrest rail buckle (G) to the seat cushion.
Using the two M6x25mm (b) screws to attach the footrest (E) to the footrest rail (F).
Insert the footrest rail (F) into the footrest rail buckle (G).
NOTE: Use the rubber ring (e) to clamp the end of the footrest rail as shown in the picture to prevent the footrest from falling -
Finishing of Exterior
note
Before assembly, please note the distinction between the two plastic shells.
The straight plastic shell is installed on the left side of the chair as shown.
The curved plastic shell is installed on the right side of the chair as shown (On the same side as the angle adjuster).
Secure the backrest and cushion with four M8x25mm (d)
screws.
Use two x M6x10mm (f) to fix N to the joint of backrest and cushion.
Press the four plastic caps(g) in the four positions as shown. -
Installation of Armrests
note
Increase the tilt angle of the lumbar pillow, you can directly pull up the lumbar pillow.
Decrease the tilt angle of the lumbar pillow, you need to pull the lumbar pillow to the highest point and then put down.
Attach the armrest to the main body as shown.
Use six M8x20mm(c) screws to attach the armrests(K) to the cushion(J).
X Please note the strength of screwing, if the backrest does not tip over, the armrest screws may be too tight. -
Installation of Cushion
The cushion can be reversible for replacement use.
« Front: perforated leather (with gel underneath), especially suitable for hot summer weather.
« Back: Short plush, suitable for all seasons outside the hot summer.
Both the front and back of the seat cushion can be fixed to the chair by Velcro. free gift
A short plush cushion cover. It can be used as a replacement for the original cushion cover, and you can replace it yourself.”
note
The original cushion cover is a cushion cover with gel cooling (not washable);
the freebie is a short plush cushion cover (washable). Assemble the upper and lower parts of the chair as shown.
If lack of energy, or install it by yourself, tilt the top side of the chair or place it on the floor, align the tilt device with the gas cylinder and insert it, then hold up the chair.
USAGE
Please read before use.
Backrest Angle Adjustment Function
When adjusting the angle of the backrest,sit on the chair and operate the reclining lever.
- Pull the lever up to release the reclining function, and tift it back to increase the angle of the backrest. If it is the other way around, it will decrease.
- Push the lever down to fix the backrest at the current angle.
Seat Height Adjustment Function
When adjusting the height,sit on a chair and operate the lf lever.
If you raise the lft lever while your hips are floating, the seat surface wil
rise.
If you raise the lft lever while sitting, the seat surface will drop.
BEFORE USE
- The purpose of this manual is to describe the items you should be aware of when using the product to prevent harm to you and other people and damage to property. Please be sure to observe it for safe use.
- Please read this manual carefully before use to ensure correct and safe use.
- Please keep it in a safe place and read it when necessary.
- When renting or transferring the product to a third party, be sure to attach this manual and fully explain the handling method.
- The warranty period is one year after delivery. If a failure occurs due to our responsibility within the above warranty period, we wil repair of replace it with a new product o free.
Please do not hesitate to contact us if any problem occurred: vigositus@163.com
SAFETY PRECAUTIONS
The precautions written here are to prevent harm or damage to you o others.
All of these are important contents for safe use, so be sure to observe them.
- Do not disassemble or lubricate the gas cylinder. It may explode and cause injury.
- Please do not incinerate. The high-pressure gas in the gas cylinder may explode or emit toxic gas.
- Do not put your hand in the gaps between the moving parts.
- Do ot operate the up/down adjustment lever on the seat surface while the seat s vacant. The seat and backrest may rise sharply and cause injury.
- Do not use ow slippery floors. You may fall and get injured To avoid safety incidents and ensure user experience, all the screws must be fully tightened before use,
- Also, if any rattling occurs due to the loosening of bolts or screws during use, check to make sure all the screws are fully tightened in a right way.
- Please do not et the infant sit alone. They may fall and get injured.
- Please do not modify unauthorized
PRECAUTIONS FOR USE
- utdoor use of this product or getting wet may cause malfunction, rust or discoloration.
- Avoid using the product in a place exposed to direct sunlight or heat, such as a stove, or in a place with significant humidity or dryness.
- Tighten the bolts and screws regularly every two months.
- Vacuum or use slightly wet cloth to remove dust or dirty on the main body of the chair. Do not use anything like bleach or benzine to clean the chair
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>