Not mentioned 250ML Mini Chopper Electric Food Processor Instruction Manual
- June 14, 2024
- Not mentioned
Table of Contents
Not mentioned 250ML Mini Chopper Electric Food Processor
Product Structure
Technical parameters
Performance characteristics
- The S-shaped three-dimensional four-leaf blade can provide better meat and vegetables minced effect;
- The design of high and low gears can help you control the food chopped degree at will. It has better tastes and can be used safely.
- Thickened glass/stainless steel cup is healthy and easy to wash;
Usage method
A. Steps
- Remove the host and the cup lid; place the cup body in a flat place and place the non-slip mat under the cup body.
- Make sure that the meat minced knife rest is properly placed on the shaft in the middle of the cup.
- Put in food (refer to the portion/work schedule)
- The ingredients added should not exceed the maximum scale of the cup as far as possible.
- Put the lid on the cup and then put the host on the lid. Check whether it is well placed and make sure that the host, the knife, and the lid are installed in place.
- Plug in the power cord and turn on the power.
- Hold the main engine with your hand, press the switch and the machine will start to work; release the switch and the machine will stop working. (Refer to the portion/work schedule)
- Do not remove the main engine immediately after the machine stops working. Pull out the plug and remove the main engine after the blade stops rotating
- Open the lid of the cup, take out the mincing knife first, and then take out the food.
(The mincing knife is very sharp. Be careful not to cut your hand or any other
part of your body when you take it out.)
Warm prompt: Do not put water or food materials with a temperature of
higher than 50°C into the cup for processing because this will damage the
cup body because of heat and cause water leakage.
Food portion/work schedule
Remarks:
- Food not indicated in the table should be operated according to the above table;
- Use the inching function for mincing vegetables when a single gear is used.
Cautions
- Do not use a power source other than AC 250V, otherwise, there will be a risk of electric shock or fire.
- Please use the socket above 6A separately. If the socket is also used by other electrical appliances, the socket circuit may cause abnormal heat and fire
- Hold the power cord plug with your hand and insert it smoothly into the power socket
- Hold the power cord plug with your hand and pull it out smoothly from the power socket.
- Do not use hard objects such as iron, to scrub the machine
- After the machine is used, you must pull out the power cord plug. otherwise, there may be a risk of electric shock, leakage of electricity, and fire.
- This product can not be used to process harder things, such as meat with bones, coffee beans, peppers, prickly ash, ice cubes or frozen food.
- Do not put the chopped cup into the microwave oven
- Before food is added, please check if the cutting knife is out of position. If the blade does not operate rapidly within a few seconds, please remove the plug. make it level and take out extra food before you continue to use it with electricity.
- After food is added, please check if the knife is out of position. If the blade does not operate rapidly within a few seconds, please remove the plug, make it level, and take out extra food before you continue to use it with electricity
- The blade is very sharp. Please do not touch the blade directly with your hands. Hold the blade rod when you take it out and install the blade.
- The machine can not be operated continuously for more than 30 seconds. After continuous working for 30 seconds, the machine shall rest for 2 minutes before it is used again. The product shall be operated for 3 consecutive working cycles with an interval of 15 minutes, and shall be operated after the motor cools down,
- The power cord must be replaced by a professional person from the manufacturer, its maintenance department, or similar departments so as to avoid danger.
- The machine blade is sharp. Please be careful when taking out the blade, emptying the mixing bowl, and cleaning the machine
- If the product stops working during operation, it may be caused by the failure of motor temperature control protection. Please turn off the power and wait for 20 to 30 minutes after the machine cools down before you use it again.
- The product should be placed in places out of the reach of children. Do not allow people (including children) with physical, sensory or mental disabilities or those lacking relevant experience and knowledge to use or play with the product.
Maintenance
- After you use the machine, please remove the power plug from the power socket in time.
- The cutting knife can be removed for cleaning. You are recommended to wear gloves for your safe operations.
- The product can only be assembled after it is cleaned and dried. It must be placed in safe sites. Do not cut your hands.
- All parts can be cleaned with detergent and sponge. Please do not use hard steel wires to clean it so as not to damage the surface.
- Do not immerse the whole machine in water. The outer surface of the product can only be wiped with a wet towel. Do not rinse it with water so as to avoid electric leakage and failure.
- If the product is not used for a long time, please clean it and put it into the packing box. Then, place it in a ventilated and dry place so that it will not be affected by moisture.
Analysis of common problems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>