Frossvt EM3205 Espresso Coffee Machine User Manual

Frossvt EM3205 Espresso Coffee Machine

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury to persons, including the following:

1. READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against electric shock, do not immerse the cord, plug, or appliance in water or other liquids.
4. Unplug the unit from the electrical outlet when not in use and before cleaning. Allow it to cool before putting on or taking off parts and before cleaning it.
5. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Please contact the Frossvt Support Team to get help. Do not attempt to replace or splice a damaged cord.
6. The use of an accessory not recommended by the appliance manufacturer for use with this appliance may result in fire, electric shock or injury to persons.
7. Do not use outdoors or for commercial purposes.
8. Do not let the cord hang over the edge of the table or countertop or touch hot surfaces.
9. Do not place this appliance on or near a hot gas or electric burner or in a heated oven.
10. To disconnect, press the switch located on the side of the unit to the off position “-” and then remove the plug from the outlet.
11. Do not use the appliance for anything other than its intended use.
12. Use on a hard, flat-level surface only, to avoid interruption of the airflow underneath the appliance.
13. Always be sure to place the water reservoir back on the unit tightly with the lid closed and water filled up to, but not surpassing the MAX line.
14. Never touch the hot appliance parts like the steam/hot water outlet, the metal part of the portafilter or the filter. Do not remove the porta-filter while brewing coffee.
15. Do not remove the water tank until the unit has stopped brewing and/or frothing.
16. This appliance is not to be used by children or by persons with reduced physical, sensory or mental capabilities.
17. Close supervision is necessary when any appliance is used near children. Children should not play with the appliance. SAVE THESE INSTRUCTIONS

KNOW YOUR ESPRESSO MACHINE

1. Water tank cover

2. Water tank

3. Steam knob

4. Main body

5. Steam pipe and nozzle

6. Steam pipe handle

7. Warm cup board

8. Piezometer

9. ON/OFF switch/ indicator

10. Single-cup coffee switch / indicator

11. Display screen

12. Double-cup coffee switch / indicator

13. Steam warm-up switch / indicator

14. Drip tray cover

15. Buoy

16. Drip tray
    ACCESSORIES

17. Spoon & Tamper

18. Double-cup coffee filter

19. Milk frother cup

20. Single-cup coffee filter

21. Portafilter

22. Latte Art Pen

INSTRUCTIONS

• Power Button
  Short press to turn on/off the machine

• 1-CUP Button
  Short press to make a single shot espresso

• 2-CUP Button
  Short press to make double shot espresso

• Steam Button
  Press to enter/exit steam mode

• Steam / Hot Water Knob

  • At coffee mode, turn on the knob, the steam wand comes out hot water;
  • At steam mode, turn on the knob, the steam wand comes out steam.

OPERATION

Before First Use

Machine Preparation

1. Remove and discard all labeling and packaging materials attached to your espresso machine. Ensure you have removed all parts and accessories before discarding the packaging.
2. Remove the water tank located at the back of the machine. Remove the red silicone from the water tank. Clean parts and accessories (water tank, portafilter, filter baskets, milk jug) using warm water and a gentle dish washing liquid, then rinse and dry thoroughly.
3. Wipe the outer housing, bean hopper and drip tray with a soft damp cloth and dry thoroughly.
4. When refilling, the water level must not exceed the “max” position marked on the water tank
5. Using hot water and steam cycles 2-3 times to deep clean the steam wand, coffee filter and cup before making coffee.
6. Do not immerse the outer housing, power cord or power plug in water or any other liquid.

NOTE
All parts should be cleaned by hand using warm water and a gentle dishwashing liquid. Do not use abrasive cleansers, pads or cloths which can scratch the surface. Do not clean any of the parts or accessories in the dishwasher.

Brewing

1. Choose your filter (single or double shot). To insert filter, make sure to align the notch on the filter with a groove on the porta-filter. Once inserted, turn the filter to left or right to secure in place.
2. Fill the filter with espresso grounds. Tamp firmly and level. Clean excess grounds from rim of the porta-filter. Please Note: The pressed espresso grounds should be lower 3mm than the filter cup. Too much or too little espresso grounds can affect the extraction of the coffee.
3. 3. Attach porta-filter to brew head of unit by aligning the handle with the icon and turn to the right until handle is aligned with the “ ” icon.”
4. Fill the removable water reservoir with water and place on unit.
5. Plugging in power, all button indicator light keep on about 1s, then press “ ” to tap re-heating for a minute, the indicator lamp of and  will keep white light on, “ ” and light off.

Start to Brew Espressos

• a. Press the Espresso Button once to brew 1-CUP shot. The machine will beep to indicate the 1-CUP volume has been finished.
• b. Press the Espresso Button once to brew 2-CUP shot. The machine will beep to indicate the 2-CUP volume has been finished. The default amount of I-CUP espresso is approx. 30ml. The default amount of 2-CUP espresso is approx. 60ml.

NOTE:
For a single shot, use the single shot filter. For a double shot, use the double shot filter. Pull out the cup height adjusting tray if you are using a small “demitasse” cup to brew espresso.

HOW TO CUSTOMIZE

HOW TO CUSTOMIZE THE BREWING TIME

1. Customizing the time of single cup espresso brewed
   Press and hold them for 3 seconds until the II if11 light fishing, then press to decrease time, press to increase time. When desired time is reached, press the once again to ensure brewing time.

2. Customizing the time of double cup espresso brewed.
   To customize the time of double cup espresso brewed, press and hold the for 3 seconds until the light fishing, then press to decrease time, press to increase the time. When the desired time is reached, press the once again to ensure brewing time.

Set the volume of 1-CU P shot:

1. Short press “ “to start to brewing.
2. Press 11 again once desired volume of espresso has been extracted. The machine will beep to indicate the new volume of I-CUP shot has been finished.

Set the volume of 2-CUP shot:

1. Short press 11 to start to brewing.
2. Press again once desired volume of espresso has been extracted. The machine will beep to indicate the new volume of2-CUP shot has been finished.

FROTHING MILK
To prepare a traditional cappuccino or latte, we recommend:

• using cold, fresh whole milk. The density of the frothed milk will depend on the milk fat content.
• using stainless steel, circular, rounded milk jugs, narrower at the top, with a spout, necessary to make cappuccino decorations.

Before starting, it is important to slightly move the steam wand outwards in order to insert the jug directly under it and facilitate the movements required to froth the milk correctly.

Continue as follows

1. Press the steam button.

2. Turn the steam knob counterclockwise.

3. Place the jug, half-filled with cold milk, under the steam wand.

4. Place the steam nozzle just below the surface of the milk. If it is inserted too deep, the milk will not be frothed; if it is not inserted deep enough, big bubbles will be produced and then disappear immediately. It is important to keep the Steam Tube not at the center but close to the edge of the jug, with an appropriate angle to produce a stronger vortex.

5. Turn the steam knob to position. The steam will come out of the steam wand.
   Note:
   

   • a. After the steam stops spraying, please clean the steam pipe assembly immediately and discharge themilk in the pipe to prevent the milk froth from scaling on the pipe wall During the operation, due to the high surface temperature of the steam pipe, be sure not to be scalded.
   • b. To froth the milk correctly, the steam nozzle must always be in contact with the milk and not with the froth. Therefore, as the layer of froth increases, the jug must be slightly raised trying to keep the Steam Tube in contact with the milk, without touching the bottom of the Jug.

6. Once the desired frothing has been achieved, the steam nozzle must be pushed deeper to heatthe milk well.

7. Once the desired result has been achieved, clockwise rotation the steam knob to ” -• position to stop dispensing steam and remove the jug.

8. Press the ” ” again to quitthe steam mode. Pour the frothed milk into the coffee.

   • WARNING: The steam wand may be very hot during and after use. To avoid burns, move It only by placing your fingers on the rubber tip fitted on the steam wand.

9. Turn the on to eliminate any residue milk from the wand then tum the knob off again.

10. Do not make coffee immediately after frothing milk. The temperature of boiler is too high, and the machine is under the over-heating protection. Under the protection, the and button will flash.

Note:
Please clean steam nozzle immediately after use, to prevent milk scaling. caution high temperature of hot water outlet when in use.

Over-heating Protection

Over-heating Protection – ERROR CODE: E-2
After having used the steam wand and exited the steam function, the machine is under the over-heating protection. under the protection, the single and double buttons will flash simultaneously if you press either of them, indicating that the boiler needs to be cooled off in order to reach the precise espresso brewing temperature.
Please proceed as below 4 steps to cool down the machine:

• a. Under the over-pressure protection, tum the steam knob to ” rfifJN, ” position to make hot water.
• b. Let hot water come out from the steam wand to cool down the boiler. c. Once the temperature of boiler is cool down, all the buttons will fully illuminated.
• d. Clockwise rotation the knob to the”-” position, and the coffee machine is ready for the next brew.

Making Hot Water

1. Turn the machine on and wait until “ “”  ” light up.
2. Place a cup under the steam wand.
3. Turn the steam knob to position.The hot water will come out of the steam wand.
4. Once the desired amount of hot water has been dispensed, clockwise rotation the steam knob to the “-11 position.

Reminder:
The hot water function can also be used to quickly cool down the coffee machine.

WARNING:
The steam wand may be very hot during and after use. To avoid burns, move it only by placing your fingers on the rubber tip fitted on the steam wand.

FACTORY DEFAULT

Keep pressing the” “and “for 3 seconds, the machine will return to its original default settings

CLEANING AND MAINTENANCE

Regular cleaning and maintenance keep the machine in working condition and ensure perfect coffee flavour, a constant coffee flow, and excellent milk froth for a long period of time.
Cleaning the Portafilter and the filters
The Portafilter and filters should be kept clean to guarantee perfect results.
WARNING To avoid burns, the filter must only be removed when the Portafilter has cooled down completely.

1. Remove the filter from the Portafilter and wash them with warm water.
2. If you notice a malfunction when brewing coffee, immerse the filter in boiling water for 10 minutes and then rinse with running water.
   • Note: Do not clean any of the parts in the dishwasher.

Cleaning the Steam Wand

1. Immediately after frothing milk, turn steam knob on to purge out any residual milk from the steam wand.
2. Clean the steam wand with a damp cloth. To clean it more thoroughly, you can unscrew the steam nozzle and wash it with running water.
3. If the hole of the steam nozzle become blocked, ensure the steam knob is in the “-” position. Press the power button to turn the machine of and allow to cool. Use a pin to unblock the hole.

Cleaning the Brew Head
Regularly remove any residual coffee grounds from the brew head using a brush, and wash with hot water following the steps below.

1. Insert the filter holder into the brew head without using coffee grounds.
2. Place an empty cup under the brew head.
3. Press the “double cup” button and fill the cup with water.
4. Remove the filter holder from the brew head and clean the brew head with a dry cloth.

WARNING Do not try to disassemble the brew head. It will damage the Brew Head and lead to leakage.

DESCALING
To make sure your coffee maker operates effciently, to clean the internal pipes, and to preserve the flavor of your coffee, the coffee machine needs to be descaled, cleaned and maintained periodically.

Please proceed as below steps to descaling the machine.

1. Fill the water with descaling agent(4 parts water to 1 part descaling agent) into the water tank up to the Max marking.
   • Note: Please also refer to the instructions on the descaling agent. Please use a household descaling agent, or you can use citric acid instead of a commercial descaling agent – in this case use 100 parts of water to three parts of citric acid.
2. Install the portafilter (no coffee powder), place a cup/mug or other suitable receptacle on the drip tray and under the steam wand, press the 11 !let II button to start make coffee one time. Turn on the steam knob to making hot water for 2 mins, then turn off the steam knob and waiting for 15 mins.
3. Repeat the previous steps until the water with descaling agent is running out.
4. Next, repeat the process two more times using only CLEAN TAP WATER without any descaling agent.

ERROR CODE

INDICATOR LIGHT STATUS

the voltage and frequency is consistent with the nameplate
The machine is faulty.| Contact our customer support.
No steam| Steam nozzle clogged| Clean the steam nozzle
The water tank is empty| Fill water tank
The machine is faulty.| Contact our customer support
Coffee run out of the Portafilter| Too much coffee in the filter.| Ensure appropriate amount
Coffee powder residue on the funnel seal| Clean funnel seals
Still error| Contact our customer support
Coffee does not or only slowly run out the Portafilter| Coffee is ground too finely| Ensure appropriate degree of grinding
Filter is clogged up| Clean the filters hole with a pin
The water tank is not installed correctly| Remove the water tank and correctly install it
Water is pooled under the coffee machine| The water tank is not installed correctly| Remove the water tank and correctly install it.
---|---|---
The drip tray is filled with water| Empty and clean drip tray
The machine is faulty| Contact our customer support
The machine does not work, or could not turn on.| Machine is not switched on or power plug is not plugged in| Make sure that the power plug is plugged in, that the ON/OFF button has been pressed and the both coffee buttons light up White
Short circuit/ power outlet is without power| Check the power supply
The machine is faulty| Contact our customer support

The steam fails to steam the milk

| The milk jug is too big or the jug shape is unsuit­ able| Always use a tall, slim contain­ er ideally made from stainless steel
You have used milk with less than 3.3% of milk protein| Use milk with more than 3.3% of milk protein
The milk is not cold| Always use cold milk(41°F)
Coffee is not enough hot| The machine is not pre-warmed| Let hot water run through the appliance with the inserted portafilter (with filter but without coee grounds) before extracting the first coffee to warm up the brew system)

Cups not pre-warmed could not turn on.

| Pre-warm cups on the top of the machine

Note: If your problem is not listed, please contact Customer Support.

WARRANTY

• The manufacturer provides a warranty in accordance with the legislation of the customer’s own country of residence, with a minimum of 12 months, starting from the date on which the appliance is sold to the end user.
• The warranty only covers defects in material or workmanship.

The warranty will not apply in cases of:

• Normal wear and tear.
• Incorrect use, e.g. overloading of the appliance, use of non-approved accessories.
• Use of force, damage caused by external influences.
• Damage caused by non-observance of the user manual, e.g. connection to an unsuitable mains supply or non-compliance with the installation instructions.
• Partially or completely dismantled appliances.

CUSTOMER SUPPORT

• If you have any questions or concerns about your new product, please contact our helpful Customer Support Team.
• Contactourteam by email:Frossvt0l@outlook.com.
• Please have your invoice and order ID ready before contacting Customer Support.
• FrossvtOl@outlook.com.
• HOUSEHOLD USE ONL: Please read all instructions carefully before using the product
• Model: EM3205

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>