Yovikin MS-672 Electric Shaver User Manual
- June 14, 2024
- Yovikin
Table of Contents
MS-672 Electric shaver
Introduction Manual
PLEASE READ AND SAVE THE MANUAL BEFORE USE
Precautions for safe use
- Please read this manual carefully before use.
- This product is suitable for shaving the hair on the human face and head. Do not use it on the eyebrows, underarms and private parts, or use it for any other purpose.
- Non-professionals are strictly prohibited from disassembling the equipment
- Please do not charge in the bathroom to ensure that it will not get wet when charging.
- Avoid dropping the product or subjecting the product to strong impact
- Please charge and use this product between 5°C and 35°C
- Please take care of the children and prevent them from using the razor as a toy.
- This product s not suitable for use by the following persons (including children): those with deteriorating physical function or mental capacity, or those with insufficient experience and use knowledge. They need to have personnel responsible for their safety to supervise or guide the use of these products before they can be used.
- To avoid injury and damage, please keep and place the razor properly and keep it away from children.
- When you find that the blade teeth are deformed or broken or the mesh is broken, please stop using it to prevent damage to the skin.
- Avoid partial damage of the cutter head, avoid inserting the cutter teeth into hard and sharp objects, and do not squeeze the cutter head forcefully.
- Before you clean the shaver, please turn off the switch, and the cleaning can only start when the body is stopped.
- Please ke the skin on the shaved area clean before use, and do not use hair spray, gel water, etc.
- Please don’t use it when you find redness, ulceration, inflammation and other skin diseases in the area where you want to shave your hair.
- In order not to damage the razor, please do ot try to shave animal hair, clothing hair balls, etc
- For health reasons, it is recommended not to use this razor for more than one person.
- Please use the supplied charging cable as much as possible to prevent the head of some charging cables from being too large to maintain good contact
Display screen Description
| Show remaining available time/used time
---|---
| Shave cleaning reminder (this reminder will appear after shaving for about
10 minutes)
| Charging or low battery reminder (the remaining available time is 10min, a
reminder will appear)
| Warning protection reminder (if the beard is stuck or the cutter head is not
installed in mplace, a reminder will appear)
| Travel lock sign
Rated Power| 8W
---|---
Input| 5V/1A
Battery Capacity| 800mAh
Charging Time| 1.5-2h
Life Time| 90min
Package Size| 16.2×13.6×7.7CM
Steps for usage
Recharge
Low battery reminder: When the screen number shows “05”, the indicator light
will flash, Will appear“ ”, Indicates that the battery is insufficient and
needs to be charged in time.
Charging connection : Insert the small plug of the charger (1) into the
bottom of the shaver, and then plug the power supply into the power socket
(2).Multiple charging methods: connect laptop/mobile power/ car/adapter
Charging: screen display“ “, The number will change as the charging time
increases
full charge: Charging logo“ “disappear, screen display (Note: 90 means shaving
time, not battery display)
- Before charging, make sure that the power of the shaver is turned off
- Do not use this product during charging, so as not to affect battery life
- A fully charged electric shaver can provide up to 90 minutes of shaving time, but due to different shaving habits, cleaning habits and beard types, the actual shaving time may be less than expected.
Travel lock
Activate the travel lock
Long press the”( ) switch button for 3 seconds, To enter the travel lock mode.When you activate the travel lock, the travel lock symbol will flash 3 times and then disappear, indicating that the lock is successful.
Unlock travel lock
Long press the”( ) ” switch button for 3 seconds, and the display will
change from “03” to “01”, indicating that the travel lock is successfully
released and the product can be used normally again.
Flush reminder
After 10 minutes of normal use after power-on, a flushing mark will appear
on the screen” —” At this time, you have to turn off the machine and rinse the
cutter head in time to prevent the accumulation of hair from affecting the
subsequent shaving effect.
How to use
6D shaving head
Shaving
Skin adaptation period
The first few shaves may not give you the desired results, and your skin
may be mildly irritated.
this is normal. It takes time for your skin and beard to adjust to the new
razor. It is recommended that you shave regularly (at least 3 times a week)
within 3 weeks to allow your skin to adapt to the new shaver.
Tip: To ensure better results, if you haven’t shaved for 3 days or more, we recommend that you trim your beard in advance.
-
Remove the transparent protective cover, press the on/off button” am tO start the shaver, the display will light up, and the remaining available time will be displayed
-
Move the shaving head slowly on your skin in a straight line or in a circular motion, touch the shaved position with your hand, and the hair can be shaved several times until it is smooth.
-
Click the” “button to turn off the power of the shaver.
Wet shaved
You can also wet your face with shaving foam or shaving gel before shaving with this razor.
To shave with shaving foam or shaving gel, follow the steps below:
-
Press the on/off button“ “once to start the shaver.
-
Move the shaving head slowly on your skin in a straight line or in a circular motion, touch the shaved position with your hand, and shave the hair several times until it is smooth.
Note: Rinse the
shaver regularly under the tap to make sure it can continue to slide smoothly
on your skin. -
After use, dry your face and clean the razor thoroughly.
Note: Make sure to rinse off the foam or shaving gel from the shaver.
Shaved head
Hold the machine and move it slowly on the head to remove the hair.
How to replace accessories
-
Pull the shaving head parts vertically away from the product.
Note: When removing the shaver head from the product, do not rotate it. -
Insert the protruding part of the trimmer attachment into the groove on the top of the shaver. Then press the accessory to install it on the shaver (you can hear a “click”)
Note: The replacement method of other accessories can be operated in accordance with the above instructions
Clippers
The clippers can shave the hair on both sides of the ears to make you look
more energetic.
-
Turn off the machine first to make the fuselage inoperative, and then buckle the cutter head into the corresponding position of the fuselage.
-
Short press the switch button, the cutter head starts to work, facing the mirror, choose the position to shave the hair, and start trimming. In the trimming process, the upper limit comb can be installed, and different sizes of limit combs (3mm/5mm/7mm) can be selected according to the length of the hair trimming.
Align the shaving head with the groove of the limit comb and put it in
Press the end of the limit comb to install it -
After trimming, turn off the machine and use a small brush or flushing to remove the dandruff adhering to the cutter head.
Facial wash brush and Silicone face brush
Use a facial wash brush or aSilicone face brush to clean your face every
day, which can remove oil and dirt on your face, which will help your health
and improve your skin.
-
Insert the protruding part of the cleaning brush attachment into the groove on the top of the product. Then press the cleaning brush attachment to install it on the product (a “click” can be heard).
-
Moisten the cleaning brush attachment with warm water, and moisten your face with cleansing cream.
Tips: Use the cleaning brush attachment to clean before shaving, which facilitates easy hair removal and brings a more hygienic shaving effect. -
Press the on/off button to start the product.
-
First use the cleaning brush attachment to clean the T area.
Note: Do not perform circular movement more than 3 times in the same position. -
Start cleaning other parts of the face.
Note:
- Use the cleaning brush attachment to clean the face for about 1 minute.
- Never clean the sensitive area around the eyes.
Nasal Hair Apparatus
-
Turn off the power of the shaver, remove the shaving head, insert the flange of the nose hair part into the groove on the top of the shaver body, and then press down the nose hair part to install it on the shaver.
Shaver on the fuselage. -
Make sure the nasal cavity is clean.
-
Turn on the machine, and slowly insert the tip of the nose hair device into a nasal cavity while rotating the tip to remove the excessively long nose hair.
The depth of the tip inserted into the nasal cavity should not exceed 0.5 cm, and it can also be used to remove ear hair. -
In order to reduce itching, make sure that one side of the tip is firmly pressed against the skin.
Cleaning and maintenance
-
Cleaning the product after each use can extend the life of the product.
-
In order to achieve the best shaving performance, it is recommended to replace the shaving head every two years.
-
This razor is a waterproof design of the whole machine, which can be cleaned and rinsed under the tap, and then wiped with a clean cloth after rinsing
-
Do not use salt water, hot water with a temperature above 60°C, thinner, gasoline, alcohol or other chemicals for cleaning.
Note: When using hot water, be sure to check that the water temperature Is not overheated to avoid hurting your hands. -
When cleaning, please do not let the bristles of the brush into the holes of the mesh, do not wipe with a towel or paper towel.
Cleaning the razor head
-
Open the cutter head components separately with a little force.
There are 5 cutter heads on the outside. Place 2 fingers on both sides of the texture of the small cutter head respectively, and then turn them upwards to open each cutter head in turn. -
For the middle cutter head, place your fingers on the 2 side of the small cutter head and turn it clockwise to disassemble
-
Use a brush to clean the dander in the hair storage room
-
After cleaning, put the knife head under the faucet to rinse off
-
Shake off the water inside the cutter head after cleaning, and buckle the cutter head in order to restore it.
The middle cutter head, align the buckle position, and rotate it counterclockwise to install it -
For the outer cutter head, just flip the cutter head inward and press it
-
Buckle in the transparent protective cover, wipe it with a dry cloth, and keep it properly.
Note: During the cleaning process of the cutter head, the Internal lubricating oll will be cleaned. After the cutter head is cleaned, please use the cutter oil (not included) to drop a drop on the surface of each cutter net, and then turn it on to make the inner and outer cutters fully lubricated.
Types of failures and treatment methods
| problem | problem analysis | Solution |
|---|---|---|
| Boot does not work | The battery is exhausted | Charge it in time, turn it on |
again after full charge
Travel lock has been activated| Press and hold the on/off button for 3 seconds
to release the travel lock.
Bad shaving results| Hair or dirt is clogging the shaving head.| Clean the
shaving head
Low battery| Charge it in time, turn it on again after full charge
The shaving heads are damaged or worn.| Replace the shaving head
Can’t charge| Not plugged in or powered off| Recheck whether the connection is
well connected and whether the power supply is normally energized
The ambient temperature exceeds the applicable range| It is recommended that
the ambient temperature during charging is 5°C to 35°C
Skin irritation after shaving| It takes a while for your skin to adjust to the
razor| After 2-3 weeks of adaptation period, the symptoms disappear
The razor head has a peculiar smell| The cutter head is not dried after
cleaning| Wipe and dry the cutter head in time after cleaning
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>