Oasser P2S Portable Air Compressor for Tires Instruction Manual

Oasser P2S Portable Air Compressor for Tires

Important Information

This product is suitable for cars, motorcycles, bikes and balls, but it cannot be used on trucks, swimming rings and air mattresses. It can be used as a tire pressure gauge.

Product schematic dia

1. Tire inflater
2. LCD
3. Power button and unit switch
4. Start button
5. Air tube chuck
6. LED lights
7. 20V battery pack
8. Air tube
9. Presta valve adapter
10. Ball needle
11. Toy nozzle
12. Usb cable
    

Installation

1. Take out the tire inflate and install the fully charged battery pack.
   

2. Connect the air tube to the tire.
   (Make sure the air tube and valve are tightly connected to prevent leakage).
   

Technical parameters

Operation steps

1. Connect the air tube to the tire valve, and fasten the chuck to prevent leakage. For French valve you need to install the presta valve adapter before connecting the air tube.
2. Press the power button to activate the LCD display and the and to set the air pressure. The display will shut down automatically after 90 seconds if you do not operate it. Or, long press the power button to shut it down.
3. Circularly press the power button you can switch the pressure units between PSI, BAR, KPA, KG/CM2 •
4. After the tire is connected, the display will show your current air pressure. Press “+” and “.” to set the desired pressure, short press is slow adjustment and long press is fast adjustment. After setting, the value in the screen will flash 4 times, which means auto setting is completed (or you can press the power button to complete the setting). Finally, press the start button to pump.
5. It would automatically turn off when the preset tire pressure reaches. (accuracy: ±2psi)
6. Remove the air tube from the tire valve, please be aware of heat!

Note: It is recommend to cool down the tire inflator for 5-10 minutes after every 8 minutes of operation, so as to extend its service life.

FAQ

What if the tire inflator cannot work?

1. Please check out the battery bars on the LCD screen and have it fully charged prior to use. 1. Contact Oasser after-sales service if you are not able to deal with the issue.

What if the inflator does not reach the target pressure after the

inflating?

1. Please check out the battery status as it’s possible that the battery is dim. Please be sure to fully charge the battery before use. 2. Figure out if there is any air leaking between the air hose and the tire valve. 3. If the unit goes too hot, please cool it down for 5 minutes before making it work again. 4. The standard pressure error is within ±2 psi.

1. Different gauges has different calibration standards so it’s not 100% right to compare one gauge to another. 2. Difference of ±2PSI is within the error range. 3. Please check if there is any air leaking between the tire valve and the air hose.

Is it normal that the inflator and the hose goes hot after inflating?

1. This is pretty normal. Please beware of the heat when taking the hose off the inflator.

Why is the inflator not suitable for large-sized swimming rings, air

mattresses and other large-sized inflatable toys?

1. Large sized swimming rings, air mattresses and large inflatable toys need low-pressure air (high-volume air) rather than high-pressure air. The inflator is meant for tires of cars, motorcycles, bicycles, etc. and all kinds of balls. You may buy other inflators suitable for high volume inflating from our store.

Why does the battery fail to be fully charged?

1. This could happen if the inflator is frequently used. Due to tens of hundreds of recharging and discharging, there would be battery loss. For instance, the battery bars drop to 3 bars from 4 while the indicating light is green. This is a normal case and the battery could still work properly.

How to install the ball need

Do not completely insert the ball needle into the air tube chuck, so as to prevent the needle exhaust hole from being completely blocked.
Please see the picture below for the correct operation:

Precautions for the use of cordless tire inflator

• It is recommended that the tire inflater should be cooled for 5-10 minutes after every 8 minutes of operation. Prevents excessive temperatures and gear wear due to prolonged operation of the tire inflator. And extend the service life of the cordless tire inflator.
• Not suitable for larger pneumatic tires, such as truck tires;
• Not suitable for inflatable air mattress, swimming rings, SUP board and other low-pressure blow inflatables
• This product is suitable for cars, motorcycles, bikes and balls, it can be used as a tire pressure gauge.

Precautions for battery maintenance

• The battery is consumable, please pay attention to the battery maintenance. It is highly suggested that the battery should be charged after each use of the air compressor.
• If the cordless air inflator is not used for more than 2 months, it is advised to charge it every 2 months and store it in a drying environment.

This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Correct Disposal of this product

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle ii responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>