Cooper Hunter LCD 1000 Remote Controller Air Conditioner Owner’s Manual

June 14, 2024
Cooper Hunter

Cooper Hunter logo REMOTE CONTROLLER
OWNER’S MANUAL

IMPORTANT NOTE:
Thank you for purchasing our air conditioner.
Please read this manual carefully before operating your new air conditioning unit.
Make sure to save this manual for future reference.
SPECIAL NOTE

  • Button designs on your unit may differ slightly from the example shown.
  • If the indoor unit does not have a particular function, pressing that function’s button on the remote control will have no effect.
  • When there are wide differentces between “Remote controller Manual” and “USER’’S MANUAL” on function description, the description of “USER’S MANUAL” shall prevail.

Remote Controller Specifications

Rated Voltage 3.0V( Dry batteries RO3/LR03x2)
Signal Receiving Range 8m
Environment -5°C~60°C(23°F~140°F)

NOTE: For model of RG10Y 1(F/H/G/K)/BGEF, If the unit is turned off under COOL, AUTO or DRY modewith the set temperature less than 24°C, the set temperature will be automatically set to 24°C whenyou turn on the unit again.
If the unit is turned off under HEAT mode with the set temperature more than 24°C, the set temperature will be automatically set to 24°C when you turn on the unit again.
Quick Start GuideCooper Hunter LCD 1000 Remote Controller Air
Conditioner - Fig NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions and How to Use Advanced Functions sections of this manual for a detailed description of how to use your air conditioner.

Handling the Remote Controller

Inserting and Replacing Batteries
Your air conditioning unit may come with two batteries(some units). Put the batteries in the remote control before use.

  1. Slide the back cover from the remote control downward, exposing the battery compartment.
  2. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
  3. Slide the battery cover back into place.

Cooper Hunter LCD 1000 Remote Controller Air Conditioner -
Controller BATTERY NOTES
For optimum product performance:

  • Do not mix old and new batteries, or batteries of different types.
  • Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.

BATTERY DISPOSAL
Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.
TIPS FOR USING REMOTE CONTROL

  • The remote control must be used within 8 meters of the unit.
  • The unit will beep when remote signal is received.
  • Curtains, other materials and direct sunlight can interfere with the infrared signal receiver.
  • Remove batteries if the remote will not be used more than 2 months.

NOTES FOR USING REMOTE CONTROL
The device could comply with the local national regulations.

  • In Canada, it should comply with CAN ICES-3(B)/NMB-3(B)
  • In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
    (1) This device may not cause harmful interference, and
    (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
  • Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

Buttons and Functions

Before you begin using your new air conditioner, make sure to famil rize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual.
Cooper Hunter LCD 1000 Remote Controller Air Conditioner -
Functions NOTE: For model of RG10B(F1/H1/G1/K1)/BGEFU1 , press together & buttons at the same time for 3 seconds will altemate the temperature display between the °C & °F scale Cooper Hunter LCD 1000 Remote Controller Air Conditioner - Functions
1

Remote Screen Indicators

Information are displayed when the remote controller is power up. Cooper
Hunter LCD 1000 Remote Controller Air Conditioner -
IndicatorsNote:
Allindicators shown in the figure are for the purpose of clear presentation. But during the actaul operation, only the relative function signs are shown on the display window.

How to Use Basic Functions

Basic operation
ATTENTION! Before operation, please ensure the unit is plugged in and power is available.![Cooper Hunter LCD 1000 Remote Controller Air Conditioner

  • Indicators 1](https://manuals.plus/wp-content/uploads/2023/11/Cooper-Hunter- LCD-1000-Remote-Controller-Air-Conditioner-Indicators-1.png) COOL Mode

    1. Press the MODE button to select COOL. mode.
    2. Set your desired temperature using the TEMP or  TEMP / button.
    3. Press FAN button to select the fan speed: AUTO, LOW, MED or HIGH.
    4. Press the ON/OFF button to start the unit.

SETTING TEMPERATURE
The operating temperature range for units is 17-30°C (62-86°F)/20-28°C.
You can increase or decrease the set temperature in 1°C (1°F) increments.
AUTO Mode
In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT operation based on the set temperature.

  1. Press the MODE button to select AUTO.
  2. Set your desired temperature using the TEMP / or TEMP V button
  3. Press the ON/OFF button to start the unit.

NOTE: FAN SPEED can’t be set in AUTO mode.Cooper Hunter LCD 1000 Remote
Controller Air Conditioner - Indicators 2 FAN Mode

  1. Press the MODE button to select FAN mode.
  2. Press FAN button to select the fan speed: AUTO, LOW, MED or HIGH.
  3. Press the ON/OFF button to start the unit.

NOTE: You can’t set temperature in FAN mode.
As a resdult, your remote control’s LCD screen will not display temperature: DRY Mode (dehumidifying)

  1. Press the MODE button to select DRY.
  2. Set your desired temperature using the TEMP or TEMP button
  3. Press the ON/OFF button to start the unit.

NOTE:FAN SPEED cannot be changed in DRY mode. Cooper Hunter LCD 1000
Remote Controller Air Conditioner - Indicators 5HEAT Mode

  1. Press the MODE button to select HEAT mode.
  2. Set your desired temperature using the TEMP or TEMP button.
  3. Press FAN button to select the fan speed: AUTO, LOW, MED or HIGH.
  4. Press the ON/OFF button to start the unit.

NOTE: As outdoor temperature drops, the performance of your unit’s HEAT function may be affected. In such instances, we recommend using this air conditioner in conjunction with other heating appliances.
Setting the TIMER
TIMER ON/OFF – Set the amount of time after which the unit will automatically turn on/off.
TIMER ON setting
Cooper Hunter LCD 1000 Remote Controller Air Conditioner -
Setting NOTE:

  1. When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example, press’5 times to get 2.5, and press 10 times to gét 5h,) The timer will revert to 0.0 after 24.
  2. Cancel either function by setting its timer to 0.0h

TIMER ON & OFF setting(example)
Keep in mind that the time periods you set for both functions refer to hours after the current time.
Cooper Hunter LCD 1000 Remote Controller Air Conditioner - Setting
1

How to Use Advanced Functions

Swing function
Press Swing button
Cooper Hunter LCD 1000 Remote Controller Air Conditioner -
SwingThe horizontal louver will swing up and down automatically when pressing Swing button Press again to make it stop Keep pressing this button more than 2 seconds,the vertical louver swing function is activated (Model dependent)
SHORTCUT function
Press SHORTCUT button Push this button when remote controller is on, the system will automatically revert back to the previous settings including operating mode, setting temperature, fan speed level and sleep feature (if activated).
If pushing more than 2 seconds, the system will automatically restore the current operation settings including operating mode, setting temperature, fan speed level and sleep feature (if activated ).
TURBO Function
Press TURBO button When you select Turbo feature in COOL mode, the unit will blow cool air with strongest wind setting to jump-start the cooling process.
When you select Turbo feature in HEAT mode, for units with Electric heat elements, the Electric HEATER will activate and jump-start the heating process.
Clean Function
Press CLEAN button Aitbome bacteria can grow in the moisture that condenses around heat exchanger in the unit. With regular use, most of this moisture is evaporated from the unit
By pressing the CLEAN button, your unit will clean itself automatically. After cleaning, the unit will turn off automatically. Pressing the CLEAN button mid- cycle will cancelthe operation and turn off the unit. You can use CLEAN as often as you like.
Note: You can only activate this function in COOL or DRY mode
LED DISPLAY
Press this button to turn on and turn off the display on the indoor unit Keep pressing this button more than 5 seconds, the indoor unit will display the actual room temperature. Press more than 5 seconds again wil revert back to display the setting temperature.
LOCK function Press together Clean button and Turbo button at the same time more than 5 seconds to activate Lock function.
All buttons will not response except pressing these two buttons for two seconds again to disable locking.
Silence function Keep pressing Fan button for more than 2 seconds to activate/disable Silence function(some units)
Due to low frequency operation of compressor, it may result in insufficient cooling and heating capacity. Press ON/OFF, Mode, Sleep, Turbo or Clean button while operating will cancel silence function
FP function
Press this button 2 times during one second under HEAT Mode and setting temperature of 17°CI62°F or 20 °C(for model of RG10B10(F/H/G/K)/BGEF). Cooper Hunter LCD 1000 Remote Controller Air Conditioner - SHORTCUT
7The unit will operate at high fan speed (while compressor on) with temperature automatically set to 8°C/46°F.
Note: This function is for heat pump air conditioner only.
Press this button 2 times during one second under HEAT Mode and setting temperature of 17 °CI62°F or 20 °C(for model RG10B10(F/H/G/K)/BGEF) to activate FP function.Press On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function. Cooper Hunter LCD 1000 Remote
Controller Air Conditioner - SHORTCUT 8The SLEEP function is used to decrease energy while you sleep(and don’t need the same temperature settings to stay comfortable). This function can only by activated via remote control For the details, please see “sleep operation ” in * USER’S MANUAL ”
Note: The SLEEP function is not available in FAN or DRY mode.
SET functionCooper Hunter LCD 1000 Remote Controller Air Conditioner -
SHORTCUT 9

  • Press the SET button to enter the function setting, then press SET button or TEMP or TEMP button to select the desired function. The selected symbol will flash on the display area, press the OK button to confirm
  • To cancel the selected function, just perform the same procedures as above.
  • Press the SET button to scroll through operation functions as follows: Fresh ( ) → Follow Me ( )→ AP mode( )
    [
    ]: If your remote controller has Fresh button, you can not use the SET button to select Fresh feature

FRESH function( ) (some units) :
When the FRESH function is initiated, the lonizer/Plasma Dust Collector(depending on models) is energized and will help to remove pollen and impurities from the air
Follow me function( ):
The FOLLOW ME function enables the remote control to measure the temperature at its current location and send this signal to the air conditioner every 3 minutes interval. When using AUTO, COOL or HEAT modes, measuring ambient temperature from the remote control(instead of from the indoor unit itself) will enable the air conditioner to optimize the temperature around you and ensure maximum comfort.
NOTE: Press and hold Turbo button for seven seconds to start/stop memory feature of Follow Me function

  • If the memory feature is activated,” On” displays for 3 seconds on the screen
  • If the memory feature is stopped, “OF” displays for 3 seconds on the screen
  • While the memory feature is activated, press the ON/OFF button, shift the mode or power failure will not cancel the Follow me function

AP function(  )(some units) :
Choose AP mode to do wireless network configuration. For some units, it doesn’t work by pressing the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.
The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details.

Cooper Hunter logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Cooper Hunter User Manuals

Related Manuals