Guiseapue A1Ke2M92R Electric Foot File User Manual

A1Ke2M92R Electric Foot File
User Manual

PRODUCT STRUCTURE INTRODUCTION

PRODUCT STRUCTURE INTRODUCTION
A. Switch
B. Main body
C. Battery indicator
D. Charging interface
E. Grinding head replacement button
F. Grinding head
G. Cleaning brush
H. USB charger

PRODUPRE CAUTIONS

1. Kids and the disabled people should use the product with adult’s quidance.
2. This product should not be used in special environments where there is corrosive or explosive gases.
3. This product cannot be used as a medical appliance.
4. Do not immerse the charging cable in water or other liquids, or rinse under the tap.Separate the hand-held part from the power cord before washing the hand-held part in the water.
5. Grinding head is only suitable for old hard and thick dead skin, such as heel, please do not use this product in normal skin parts.
6. If you have any pain or discomfort, stop using it immediately. Excessive use of the grinding head will lead to that the skin becomes too thin, which can easily cause skin irritation. If the skin is severely allergic or bleeding, please consult a doctor promptly.
7. To prevent accidents and damage to your body, please keep away from your scalp, hair, eyebrows, eyelashes or clothing, wool, laces, etc. when using for dermabrasion.

INSTRUCTIONS

Charging
Note:
a. Please fully charge the product before using it for the first time.
b. USB charging, the indicator lights when charging. The indicator light stops flashing and charging is completed (Charging time do not exceed 12 hours)”
Assembly and disassembly of the grinding head.
Replace the grinding head according to the following procedures.
The selection and replacement of the grinding head can be based on the roughness of the skin and the design effect to choose the appropriate grinding head.

1. Hold the head of the product with one hand and press the heel and ring button (the side button of the product) with the other hand. The head cover will be opened and removed. (See Figures 1 and 2).
2. When changing the grinding head, put a new grinding head into the product until you.
3. Hear a “click” sound. Make sure that the newly loaded grinding head is in place. If the grinding head is not connected, please do not tum on the switch.

Note:
When opening the package, a grinding head has been installed on the body.
Ensure that the power is disconnected and the machine is turned off before replacing the grinding head.

INSTRUCTIONS FOR USE

1. Ensure that the product has sufficient power.
2. Make sure that the quartz grinding head is attached to the product. According to the roughness of the skin, choose the grinding head.
3. Press the switch.Gently move the grinding head on the dry and rough skin area for 2-3 seconds. Press the switch.
4. 2 speeds in a single button – 1700x / min at low speed and 2000x / min at high speed. The low speed is suitable for the callus of the hands and for the most delicate skin care. The high speed is suitable for often stubbom callus and dead skin.
5. After using it, please turn it off. Please clean the product in time after using it. Than, rinse the skin and remove excess keratin with wet towel.

Note:

1. This product is designed for dry and rough foot or heel skin. Do not use it in other parts of the body.
2. Do not press too tightly, let the grinding head gently pass over the skin. If the press it too tightly and the force is too much, the product will be unable to continue.
3. If your skin becomes sore or inflamed, please stop using it immediately.Do not keep it on some part of the skin for more than 2-3 seconds.

Three kinds of grinding heads

Fine grinding head: It is suitable for old cocoon on hand, cocked deadskin and more delicate skin care.
Medium grinding head: It is suitable for the newly formed cocoon and the care of normal skin.
Rough grinding head: It is suitable for the thick cocoon formed by the accumulation of many years and the care of thick skin.
Technical Parameters
Power:3W
Charging voltage: 5V==
Battery Capacity: 1200 mAh
Please keep this manual properly

British Representative:
Business name: GSG CONSULTING GROUP LIMITED
Business address: Unit 3 Matthew street Gorton Manchester
Email: GSG–GROUP@outlook.com
Tel: +44 7927638013
European Representative:
Business name: Like Sun GmbH
Business address: Planckstr. 59, 45147 Essen
Email: ec-connection@web.de
Telefon: +49 471 39156605

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>