Lenso Vision L003 Projector User Guide

Lenso Vision L003 Projector

Thanks for your purchase. For any inquiries, contact us at hello@lenso.co or on our website www.lenso.co

Safety Instructions

Read all instructions before you use this device. Do not make any changes or create settings that are not described in this manual. If physical damage, loss of data or damage is caused by failure to follow instructions, the warranty does not apply.

Setup

1. To reduce the risk of fire or electric shock, do not expose the device to rain or moisture. Objects filled with liquids, such as vases, should not be placed on this device.
2. Do not place this device on soft surfaces such as tablecloths or carpets, otherwise the device could be a fire hazard.
3. Do not place this device in areas susceptible to excessive dust and dirt or near any appliance generating a strong magnetic field.
4. To prevent overheating, do not block or clog the ventilation holes.
5. Never place this device in a confined space. Always leave enough space around this device for ventilation.
6. Protect this device from overexposure to direct sunlight, heat, large temperature fluctuations and moisture. Avoid extreme temperatures. The suitable operations and storage temperature for this device and its accessories is (0° F to 95° F).
7. When this device is running for a long period of time, the surface may become hot. Shut it down immediately and unplug the charger.Resume operation after this device has cooled down.
8. Always handle this device with care. Avoid touching the lens. Do not allow children to handle the device without supervision.
9. Never place heavy or sharp objects on this device.
10. To avoid electric shock, do not disassemble.
11. Use attachments or accessories specified by the manufacturer only.
12. Avoid extreme vibration as it may damage the internal components.

The following safety instructions ensure the long service life of the projector to avoid fire or electric shock. Please read carefully and pay attention to the following warnings.

1. Don’t install the projector in sites with improper ventilation
2. Don’t install the projector in sites with improper ventilation
3. Don’t cover the projector ventilation holes with any material
4. Don’t install the projector in dust and smoke sites
5. Don’t install the projector near the temperature and smoke transducer. It may cause a sensor failure.
6. Don’t install the projector in sites with direct blowing of warm and cool air-condition wind.
7. Please do not look into the lens when the projector is working, otherwise it may hurt your eyes.
8. Please keep the projector away from water or any other liquid as it is not waterproof.

Attention

Please read this manual carefully before use and keep it for future reference.

1. Please use the power cable with caution to avoid unduly bending. A damaged power cable may cause electric shock.
2. Please use the projector with caution to avoid dropping or shocking, which may damage the internal components.
3. Please use the same power voltage as marked on the projector.
4. Please use the projector in a dark room for the best results.
5. Please do not disassemble the projector by yourself, otherwise the warranty will be void.
6. Please turn off and unplug from the power supply if not using the projector for a long time.

Introduction

Lenso Vision is the new series of LEN SO. This comes along as a mini projector ultra-thin HD 1080 pixel. Fits in your palm, and 1-hour playtime with 15 minutes only for a quick charge! It has a sensitive touch with lights. You can enjoy your home cinema at any time. Your media is stored in the device’s memory and it also has high fidelity speakers.

PACKING LIST

• 1 projector Lenso Vision
• 1 unit Power Cable
• 1 unit HDMI cable
• 1 unit AV Cable
• 1 unit Remote Control
• 1 unit Lens Cover
• 1 unit Screw Stand
• 1 unit User Manual
• 1 unit TV Box
• 1 unit Quick Reference Guide
• 1 unit TV Box HDMI Cable
• 1 unit Micro-USB Cable
• 1 unit Clean Tool

Basic Parameters

• Product size: 286 x 251 x 107 mm
• Video format: MKV / WMV /MPG / MPEG /DAT/ ISO / MP4 /RM/ JPG
• Audio format: MP3 / AAC / WMA /RM/ FLAC /OGG / M4A / MP4 / AAC /APE/ FLAC / MP1/2 etc Image format: JPG, PNG, BMP, etc
• Control: button(ON-OFF/switch), or IR/2.4G wireless remote
• Built-in speakers: 2*5 Watt
• Power input: 100-240V (50/60 HZ)
• 1/0 Port: USB 2.0 IN1, HDMI IN1, 3.5mm audio out1, DC 5V IN1, TYPE-C IN*1

Projection Parameters

• Display technology: DL P (0.2″DMD)
• Light source: LED
• LED luminance: 230 ANSI Lumens
• LED life: 30,000 hours
• Contrast: 2000:1
• Project ratio: 1,25:1
• Distortion: <1 o/o
• Brightness Uniformity: >85%
• Projection distance: 0.5-3m
• Aspect ratio: 16:9
• Focus mode: manual
• Keystone correction: Manual Horizontal, Automatic Vertical: ±40 degrees
• Projection mode: Front, Rear, Ceiling, Rear Ceiling

SYSTEM

• Screen mirror: Eshare/Airplay/MiraCast
• Operating system: Android 10.0
• RAM: 2 GB DDR3
• ROM flash: 8GB
• WiFi: 2.4G/5G
• Bluetooth: BT 5.0
• Net weight: 2.41 kg
• 2-years warranty
• Certificate FCC / CE / RoHS

Tips

1. Blurry Image
2. Slightly correct the keystone to a rectangle.
3. Press the focus button on remote control to get the best clarity
4. Slightly swing the angle of the machine to autofocus.
5. Go to settings – focus mode – pop-up window to choose manual focus
6. Press the focus button on the remote control to obtain the best clarity.
7. Mounting Hole

Adopting a single mounting hole dual-use design, the projector is compatible with the standard camera tripod and 1 /4 inch screw projector tripod stand. Meanwhile, you can rotate 360° the screw to meet different projection angle needs.

TV Box Installation

• Step 1 : Locate the side cover of the machine and open it
• Step 2 : Insert the TV Box into the corresponding connection port
• Step 3: Close the side cover to complete the installation

After installing the ANDROID TV, please pair the remote control before using it

Network setting

• Enter Setting at ANDROID TV interface – Network to turn on the WIFI and connect to an available network
• Some common apps (Youtube, Netflix, etc) are pre-installed by default in the ANDROID TV box. You can download more than 8000 apps from all over the world in the store, such as Prime Video/Disney/ Hulu/ Sling TV/ Spotify/ HBO Max, etc.
• If you want to mirror your cell phone to projector, its easily to download app from ANDROID TV system and cell phone store.

Getting Started

1. Plug the power cord to the projector.
2. Press power button to turn on the projector
3. Connect projector to HDMI port support device
4. Select the input source
5. Adjust here accordingly
6. Use the autofocus by pressing the “Focus” button on the remote control
7. Press the power button to turn off the projector

Tips:

1. lf the image is displayed as a trapezoid shape, you could adjust the KEY STONE on the projector. It could normalize the display image.
2. Make sure the projector is horizontal to the projector screen.

Android TV User Guide/ Remote Pairing

1. Android TV

2. Enter Android TV from Homepage, pair the remote control according to the prompts on the screen.

3. Insert battery to the remote, hold the remote near to the TV box. On the remote, press the “Volume – (down)” and “OK” keys together for about 1 O seconds then release.

4.  After the remote control is paired successfully, the interface can be operated, then the projector cover can be installed.
   Note : If the above operations cannot make the remote control operate the projection interface, it means that the pairing is not successful, need to pair again.
   When the cables of the TV box are all connected, press the reset button of the dongle with a needle for 3 seconds, and the pairing interface will appear. Follow the instruction 1 and 2 to re­pair.

5. After the pairing is successful and the cover is closed, operate the remote control or projector buttons to enter Android TV on homepage. Press “Return” button to return to homepage. Press the menu button to return to the main interface according to the selection in the pop-up window.

6. In Android TV mode, press the source button of the remote control to return to the main interface, the remote control will automatically switch to IR mode. Enter Android TV from the main interface again, use the remote control or the projector buttons to operate Android TV. For convenient usage, switch the remote control to Bluetooth mode and pair the remote control again. (( Put remote control close to projector, press and hold OK and Volume- button for 4 seconds, blue LED is on.(There are differences on each remote control, may need to try twice) The projector will prompt the pairing interface, then press and hold the remote control OK and Volume- for 1 O seconds, the remote control LED will flash red to blue light, the pairing is successful, projector will show a pairing success interface.

Remote Control

Attention:

1. Do not submerge the remote control in the water.
2. Do not put the remote control near fire or in wet or hot places.
3. Do not use old and new batteries together in the remote control.
4. Please take the batteries out if not using the remote control for a long time to avoid battery leakage.
5. Please point the remote control toward the IR receiver.
6. Please use the remote control within 6 meters distance and 30 degree angle.

Projector Focus

Connection

USB connection

• * Insert the USB flash/storage hard drive Into the USB port and choose USB as the source from the menu.![Lenso-Vision-L003-Projector-FIG- \(18\)](https://manuals.plus/wp-content/uploads/2023/11/Lenso-Vision-L003-Projector-FIG-18.png)

Supported multimedia formats
Choose the content which you need to play

HDMI connection

• Use the HDMI port to connect computers and HDMl-compatlble devices. Once connected, select the HDMI signal source.

HDMI
The terms of HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

Tips:

1. Mini Display Port to HDMI Cable, Thunderbolt to HDMI Adapter are needed to be compatible with Apple iMac, MacBook, Surface, ThinkPad.
2. Supported resolution: 576P, 480P, 720P, 1080P, 640×480, 800×600, 1024×768, 1280×1024, 1280×720, 1440×900, 1366×768, 1920×1080, 1280×800, 1440×960, 680×1050

3.5mm audio connection

• Use a 3.5mm audio jack to connect headphones and speaker equipment.

AV connection

• Use an AV Signal cable to connect the DVD with projector, once connected, select the AV source.

Tips : Support NTSC/PAL

Android TV
The following functions are only available in the Android TV system.

Automatic speech recognition (ASR)

• Press this button and speak, it can transform natural spoken language into a machine-readable format.
• If you want to mirror your cellphone to projector, you can download app on the ANDROID TV system and cellphone store.

Tips:
Copyrighted content from Netflix, and similar services CAN NOT be mirrored or screencast

Menu Settings

Projector Installation

Place your projector on the ceiling

1. When installing the projector on the ceiling, please purchase a projector bracket recommended by an installation professional and follow the instructions supplied with the bracket.
2. Before installing the projector on the ceiling, please check if the mounting structure can support the weight of the projector and the bracket. If in doubt, please consult the advice of an installation.
3. Fixed Hanger Screw Hole Type: 1 /4 inch
   NOTE: Projector bracket and screw (s) are not included .

Technology Features

Parameters

Resolution

__

Maximum compatible

| 1920*1080

__

__

1920*1080,4K(H.265)

| __

Input

| __

A V1/USB 1 / HDMl *1

resolution| Output| Earphone
Light| LED| Speaker| 4Q5W*2
__

Focus mode

| Electrical Focus/Auto Focus| __

Unit size

| __

286235107mm

Aspect ratio| 16:9| Net weight| 2400g
Projector ratio| 1.36:1| |

Projection Distance and Screen Size

Recommended Projection Distance: 45-103 inches
NOTE : Because the optical device has about 3% error, the above data is for reference only, please Install the projector according to the actual measurement.

Troubleshooting

Safety instructions

• Please pay attention to important information related to the operation and maintenance of the projector. You should read this information carefully to avoidproblems. Following safety instructions will increase the life of the projector.
• Please consult the qualified personnel for installation and repair services, and do not use damaged wires, accessories, and other peripherals.
• The projector should be kept away from flammable, explosive, strong electromagnetic interference (large radar stations, power stations, substations), etc. Strong ambient light (avoid direct sunlight), etc.
• Do not cover projector vents.
• Please use the original power adapter.
• Keep adequate ventilation and make sure vents are not covered to avoid projector overheating.
• When the projector is working, please do not look directly into the lens, the strong light flashes your eyes and causes slight pain.
• Do not bend or drag the power cord.
• Do not put a power cord under the projector or any heavy objects.
• Do not cover other soft materials on the power cord.
• Do not heat the power cord.
• Avoid touching the power adaptor with wet hands.

LENSO branded items purchased from lenso.co include a 2-year limited replacement warranty. For Customer Service, please contact us via email hello@lenso.co
The Lenso® name and logo are registered trademarks. LENSO. All Rights Reserved.
Imported by OUI SMART 15 RUE DES HALLES 75001 PARIS, FRANCE
www.lenso.co
Read Instructions Before Operating

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>