metabo RF 60 Compressed Air Tyre Inflation Instruction Manual
- June 15, 2024
- metabo
Table of Contents
metabo RF 60 Compressed Air Tyre Inflation
Product Information
The product is a tyre inflation measuring device designed to measure tyre air pressure and inflate tyres. It operates withoil-free compressed air or nitrogen and requires an upstream filter if oily air is used. The device has a pressure gauge with different measuring units (BAR, PSI, KG/CMQ, Kpa) and can be switched on/off using the ON button. It is powered by two lithium batteries (1.5V, type AAA), which can be replaced when needed. The device is calibrated before delivery and requires recalibration after the specified test period. The validity of calibration is 2 years.
Product Usage Instructions
- Connect the tyre inflation measuring device to the compressed air supply using the screw connection or coupling.
- To measure tyre pressure and inflate tyres:
- Press the connector (4) firmly onto the tyre valve and secure it with the locking lever (3).
- Hold on to the hose.
- Read off the tyre pressure from the scale.
- To inflate, pull the lever (2) up fully.
- To release/reduce pressure, pull the lever (2) only as far as the 1st stop (middle position).
- To release/reduce pressure using the pushbutton (1):
- Read off the tyre pressure from the scale.
- Pull the lever (2) to inflate.
- To release/reduce pressure, press the pushbutton (1).
- To switch on/off the pressure gauge:
- Press the ON button to switch on the pressure gauge.
- Press the ON button once again until the desired measuring unit is displayed (BAR, PSI, KG/CMQ, Kpa).
- After approximately 15 seconds, the pressure gauge switches off automatically.
- To inflate, pull the lever (2) up fully.
- To release/reduce pressure, pull the lever (2) only as far as the 1st stop (middle position).
- To change batteries:
- Remove the screw with a small screwdriver.
- Remove the old batteries and replace them with two new lithium batteries (1.5V, type AAA), ensuring correct polarity.
- Maintenance and care:
- Take care when using the pressure gauge and avoid bumps and knocks to keep it in good condition.
- Environmental protection:
- Dispose of the product and packaging materials according to national regulations on environmentally compatible disposal and recycling of pneumatic tools.
- Do not cause risks to people or the environment.
- Repair:
- Repairs must be carried out by qualified specialists using original Metabo spare parts.
- Contact your Metabo service center for repairs.
OVERVIEW
Operating instructions
Specified use:
The tyre inflation measuring device is designed to measure tyre air pressure
to inflate tyres. The user bears sole responsibility for any damage caused by
improper use.
Safety instructions:
- The maximum supply pres-sure specified on the air tool must never be exceeded.
- Only operate with oil-free compressed air or nitrogen; an upstream filter must be used if oily air is used!
- Keep air tools away from children.
Initial operation:
Connect tyre inflation measuring device (using screw connection or
coupling) to the compressed air supply.
Operation:
Press the connector (4) firmly onto the tyre valve and secure on tyre valve
with locking lever (3). Hold on to the hose. lever (3). Hold on to the hose.
- RF 80 G:
- Read off tyre pressure at scale.
- To inflate, pull lever up (2) fully.
- To release / reduce pressure, pull lever (2) only as far as the 1st stop (middle position).
- RF 60 / RF 60 G:
- Read off tyre pressure at scale. Pull lever (2) to inflate.
- To release / reduce pressure, press the pushbutton (1).
- RF 80 D (with digital pressure):
- Press the “ON” button to switch on the pressure gauge.
- Press the “ON” button once again until the desired measuring unit is displayed (BAR → PSI → KG/CMQ → Kpa). After approx. 15 seconds, the pressure gauge switches off automatically.
- To inflate, pull lever up (2) fully.
- To release / reduce pressure, pull lever (2) only as far as the 1st stop (middle position).
Changing batteries: Remove the screw with a small screwdriver. Remove the batteries and replace them, ensuring that polarity is correct. (2 lithium batteries 1.5 V, type AAA).
Maintenance and care
- Take care when using the pressure gauge and keep it in good condition.
- Avoid bumps and knocks.
RF 80G, RF 60G: Device is calibrated before delivery and must be submitted by the user for recalibration after the test period has elapsed. The test period is specified on the device.
-
Validity of calibration: 2 years.
(German Weights and Measures Act section 35) -
Storage : cleaned, dry, dust-free, not below 5° C.
Environmental protection: Observe national regulations on environmentally compatible disposal and on the recycling of disused pneumatic tools, packaging and accessories. You must not cause risks to people or the environment. Packaging materials must be disposed of according to their labelling in accordance with municipal guidelines.
Further information can be found at www.metabo.com in the “Service” section.
Repair : Danger! Repairs must be carried out by qualified specialists only using original Metabo spare parts! Please contact your Metabo service centre.
See www.metabo.com.
Metabowerke GmbH Metabo-Allee 1 72622 Nuertingen Germany www.metabo.com 170 27
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>