RICOH Ri 1000X Option Platen User Guide
- June 15, 2024
- RICOH
Table of Contents
RICOH Ri 1000X
Option Platen
User Guide
For Hat Platen/Shoe Platen/Sleeve Platen
Face Covering Platen
How to Read the Manuals
Before You Begin…
Only appropriately trained users should operate the machine.
Disclaimer
Contents of this manual are subject to change without prior notice.
To the maximum extent permitted by applicable laws, in no event will the
manufacturer be liable for any damages whatsoever arising out of failures of
this machine, losses of the registered data, or the use or non-use of this
machine and operation manuals provided with it.
Make sure that you always copy or have backups of the data registered in this
machine. Documents or data might be erased due to your operational errors or
malfunctions of the machine.
In no event will the manufacturer be responsible for any documents created by
you using this machine or any results from the data executed by you.
Notes
Read this manual carefully before you use the machine and keep it handy for
future reference.
For safe and correct use, be sure to read Safety Information before using the
machine.
The manufacturer will not be responsible for any damage or expense that might
result from the use of parts other than genuine parts from the manufacturer
with your products.
For good output quality, the manufacturer recommends that you use genuine ink
from the manufacturer.
Some illustrations in this manual may be slightly different from the machine.
Certain options may not be available in some countries. For details, please
contact your local dealer.
Depending on which country you are in, certain units may be optional. For
details, please contact your local dealer.
Printing Method
1.1. Target Printer
This document applies only to Ricoh genuine platen only.
1.2. Setup Printer
Refer to Ricoh Ri series Direct to Garment Printer Manual.
1.3. Printing method for Textile Productionsever
1. Start Textile Productionsever.
2. Input the image to Textile Productionsever.
3. Please set with Textile Productionsever according to the platen type.
| Platen type | Textile Productionsever |
|---|---|
| Hat | a) User select Media size |
CAUTION (*1)
Sleeve| a) User select Media size
Shoe| a) User select Media size
b) User set Offset/Scaling
Face Covering| a) User select Media size
b) User set Offset/Scaling
*(CAUTION 1)
The image is printed 180 degrees inverted from the display on the Textile
Productionserver.
In that case, the user should set 180 degrees.
The print settings are below. 
a) User select Media size
Textile Productionserver: b) User set Offset/Scaling
♦ For “Shoe Platen”**
According to type of Shoe Attachment, user set Height x Width, Offset x,
y.
If you want to
print on both feet, please prepare the following image and set Offset x,y.
Offset of each Shoe attachement
Shoe Attachment| Offset| (Reference)
Printable Area(Width x Height)| (Reference)
Distance between printable areas
---|---|---|---
Small| X:20 Y:220| 85 x 150 mm| 205 mm
Medium| X:40 Y:360| 50 x 50 mm| 40 mm
Large| X:40 Y:350| 60 x 60 mm| 40 mm
Setting method of Textile Productionserver: ♦ For “Face Covering Platen”
User set Height x Width, Offset x, y.
IMPORTANT! If you print with “Printing on the entire surface” method, depending on image, it may print to the area outside the platen.
In the figure below, it may be printed in the red area.
Offset of Face Covering Platen
Printing Method| (Reference)
Offset| (Reference)
Printable Area(Width x Height)
---|---|---
Printing on the entire surface| [Front side] X: 40
Y: 100
[Back side] X: 40
Y: 275| 330 x 120 mm
Printing one side surface| [Front side] X:10
Y:90 [Back side] X: 10
Y: 265| 385 x 140 mm
If you want to print on multiple medias, please prepare the following image
and set Offset x,y. Setting method of Productionserver:
See page 6 “For “Shoe Platen””.
4. User print image in Textile Productionserver.
5. Please lower the height according to the option platen. If you do not
lower the height, the platen may hit the printer body.
6. Press [SET] on the printer panel. 
Appendix
2.1. Revision history
| Revision | Date issued | Description |
|---|---|---|
| Initial version | February, 2023 |
© 2023 Ricoh Co., Ltd.
J110-6624
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>