RICOH Ri 4000 Option Platen User Guide
- June 15, 2024
- RICOH
Table of Contents
RICOH Ri 4000 Option Platen
How to Read the Manuals
Before You Begin…
Only appropriately trained users should operate the machine.
Disclaimer
Contents of this manual are subject to change without prior notice.
To the maximum extent permitted by applicable laws, in no event will the manufacturer be liable for any damages whatsoever arising out of failures of this machine, losses of the registered data, or the use or non-use of this machine and operation manuals provided with it.
Make sure that you always copy or have backups of the data registered in this machine. Documents or data might be erased due to your operational errors or malfunctions of the machine.
In no event will the manufacturer be responsible for any documents created by you using this machine or any results from the data executed by you.
Notes
Read this manual carefully before you use the machine and keep it handy for future reference.
For safe and correct use, be sure to read Safety Information before using the machine.
The manufacturer will not be responsible for any damage or expense that might result from the use of parts other than genuine parts from the manufacturer with your products.
For good output quality, the manufacturer recommends that you use genuine ink from the manufacturer.
Some illustrations in this manual may be slightly different from the machine.
Certain options may not be available in some countries. For details, please contact your local dealer.
Depending on which country you are in, certain units may be optional. For details, please contact your local dealer.
Printing Method
Target Printer
This document applies only to Ricoh genuine platen only.
Setup Printer
Refer to Ricoh Ri series Direct to Garment Printer Manual.
Printing method for Textile Productionserver
- Start Textile Productionserver.
- Input the image to Textile Productionserver.
- Please set with Textile Productionserver according to the platen type.
| Platen type | Textile Productionserver |
|---|---|
| Hat | a) User select Media size |
CAUTION (*1)
Sleeve| a) User select Media size
Shoe| a) User select Media size
b) User set Offset/Scaling
Face Covering| a) User select Media size
b) User set Offset/Scaling
The image is printed 180 degrees inverted from the display on the Textile Productionserver.
In that case, the user should set 180 degrees.
The print settings are below
Default Settings:
After Set Rotate(180 degree)
a) User select Media size
Textile Productionserver:
b) User set Offset/Scaling
- For “Shoe Platen”
According to type of Shoe Attachment, user set Height x Width, Offset x, y.
If you want to print on both feet, please prepare the following image and set Offset x,y.
Offset of each Shoe attachement
Shoe Attachment| Offset (Reference) Printable Area(Width x Height)|
(Reference) Distance between printable areas
---|---|---
Small| X:20 Y:220 85 x 150 mm| 205 mm
Medium| X:40 Y:360 50 x 50 mm| 40 mm
Large| X:40 Y:350 60 x 60 mm| 40 mm
Setting method of Textile Productionserver:
Default Settings:
After Set Offset(X =40, Y=350)
- For “Face Covering Platen”
User set Height x Width, Offset x, y.
IMPORTANT! If you print with “Printing on the entire surface” method, depending on image, it may print to the area outside the platen. In the figure below, it may be printed in the red area.
Offset of Face Covering Platen
Printing Method
| (Reference) MOffset|
(Reference) Printable Area(Width x Height)
---|---|---
Printing on the entire surface
| [Front side] X: 40
Y: 100
[Back side] X: 40
Y: 275| 330 x 120 mm
Printing one side surface
| [Front side] X: 10
Y: 90
[Back side] X: 10
Y: 265| 385 x 140 mm
If you want to print on multiple media, please prepare the following image and set Offset x,y
Setting method of Productionserver:
See page 6 “For “Shoe Platen””.
Adjust the platen height.
For details on height adjustment, see the user manual.
Send the print job to the printer.
For details, refer to the ColorGATE Productionserver help or user manual.
After the print preview appears on the preview window, press [PRINT START].
Appendix
Revision history
| Revision | Date issued | Description |
|---|---|---|
| Initial version | September, 2023 |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>