X-Treme Stores EU C.L.2000 Professional Treadmill User Manual

X-Treme Stores EU C.L.2000 Professional Treadmill

Treadmill User’s Manual

Product specifications may differ from the photo and are subject to change without notice.

Product Information

• This treadmill can be used in commercial gyms, and clubs for bodybuilding, sports training, teaching, etc.
• To avoid the danger of power shock, please unplug the treadmill before cleaning or repairing it. The power cord must be plugged into a grounded outlet when in use.
• It cannot be used outdoors or in places with high humidity.
• Keep an empty space of 2000*1000mm behind the treadmill.
• Kids, the disabled, and new users must be guided by professionals.
• Before use, please wear proper sports attire and shoes. Remember to consult your personal trainers to avoid injury due to incorrect or over-exercising.
• Before use, please attach the Emergency Safety Clip. The treadmill needs to be stopped in an emergency by pushing down the RED Emergency button or dragging the Safety Clip.
• During usage, do not let shoelaces or towels touch the working parts of the treadmill. Do not touch the bottom and working parts with your hands.
• The treadmill handlebar is only for the purpose of the user’s stability and should not be used continuously during a workout.
• Do not leave or get on the treadmill while it is working, and do not walk in the reverse direction.
• If there is an emergency during a workout, please hold onto the handlebars and step on the side rails. Then push down the emergency button and leave the treadmill.
• After training, switch off the power and unplug the power cord to ensure it is not used by others.

CAUTION! The company does not have any responsibility for causing damage due to misuse of the product and non-compliance with the instructions for use.

THE WARRANTY IS NOT VALID IF:

• The treadmill is placed outdoors or exposed to sun and dust. Dust and fluff may enter the internal mechanical parts, causing serious damage. Keep the treadmill free of dust and fluff.
• The use of a protective carpet (plastic carpet or thin carpet) under the fitness machine is considered essential for proper use, avoidance of vibrations, and protection of the floor. The company does not bear any responsibility for causing damage due to misuse of the product and non-compliance with the instructions for use.

Product Usage Instructions

1. Ensure the treadmill is placed in a commercial gym or club setting.
2. Before cleaning or repairing, unplug the treadmill to avoid the danger of power shock.
3. Plug the power cord into a grounded outlet when using the treadmill.
4. Avoid using the treadmill outdoors or in places with high humidity.
5. Keep an empty space of 2000*1000mm behind the treadmill.
6. Kids, the disabled, and new users must be guided by professionals.
7. Wear proper sports attire and shoes before using the treadmill. Consult personal trainers to avoid injury due to incorrect or over-exercising.
8. During usage, do not let shoelaces or towels touch the working parts of the treadmill.
9. Avoid touching the bottom and working parts of the treadmill with your hands.
10. Use the treadmill handlebar for stability but do not use it continuously during a workout.
11. Do not leave or get on the treadmill while it is working. Do not walk in the reverse direction.
12. In case of an emergency during a workout, hold onto the handlebars, step on the side rails, push down the emergency button, and leave the treadmill.
13. After training, switch off the power and unplug the power cord.

• Product specifications may differ from the photo and are subject to change without notice.

INSTRUCTIONS

Safety Tips: This instruction contains important information of safety use. Please read
carefully before use.

1. This treadmill can be used in commercial gym, and clubs for bodybuilding, sports training, teaching, etc.
2. To avoid the danger of power shock, please DO plug off the treadmill before cleaning or repairing; The power cord must be plugged into the grounded outlet when usage.
3. It cannot be used outdoors or in places of high humidity. Keep an empty space of 2000*1000mm behind the treadmill.
4. Kids, the disabled, and new users must be guided by professionals.
5. Before use, please wear a proper sports suit and shoes. Remember to consult your personal trainers to avoid injury due to incorrect or over-exercising.
6. Before use, please DO put on the Emergency Safety Clip. The treadmill needs to be stopped in an emergency by pushing down the RED Emergency button or drag the Safety Clip.
7. In usage, DO NOT let the shoelace or towel touch the working parts of the treadmill; DO NOT touch and working parts with your hands.
8. The treadmill handlebar is only for the purpose of user stability, not to be used continuously in workouts.
9. DO NOT leave or get on the treadmill when the treadmill is working; DO NOT walk in the reverse direction.
10. If there is an emergency in a workout, please hold on the handlebars and step on the side rails. Then push down the emergency button and leave the treadmill.
11. After training, DO switch off the power and plug off the power cord in case of it is used by users without permission. (The front power cord is pluggable and easy to plug off. Keep the power cord properly.)
12. If there is exceptional noise, please STOP the treadmill immediately and contact our after-sales department or professionals.
13. The treadmill is in class S and grade C, conforming to EN957-1:2005, and EN957-6:2010 standards.
14. Warning! Heart-rate data may not be 100% correct. Over-exercising may cause injury or even death. If feeling dizzy, STOP training immediately.
15. For the operation of the console, refer to the instructions followed.

CAUTION! The company does not have any responsibility for causing damage due to misuse of the product and non-compliance with the instructions for use.

THE WARRANTY IS NOT VALID IF:
The treadmill is placed outdoors or exposed to sun and dust. Dust and fluff enter the internal mechanical parts of the machine through the treadmill, causing serious damage. Keep the treadmill free of dust and fluff.

CAUTION! The use of a protective carpet (plastic carpet or thin carpet) under the fitness machine is considered essential for its proper use, avoidance of vibrations and protection of the floor. The company does not bear any responsibility for causing damage due to misuse of the product and non- compliance with the instructions for use.

EXPLODED DIAGRAM

PART LIST

NO.| NAME| QTY| NO.| NAME| QTY| NO.| NAME| QTY
---|---|---|---|---|---|---|---|---
01| Body frame| 1| A1| Edgings L| 1| B1| Non-slip nuts    M14| 4
02| Stand column| 2| A2| Edgings R| 1| B2| Homemade screw M14| 2
03| Footstool| 1| A3| Footboard L| 1| B3| Cup gasket| 24
04| Big frame| 1| A4| Footboard R| 1| B4| PWB M5*10| 16
05| Heart rate inner pipe| 2| A5| The end covers L| 1| B5| Cylinder head hex socket ****screws M5*15| 9
06| Foot margin| 2| A6| The end cover R| 1| B6| **Flat gasket ∅ 18* ∅ *6.5T1 **| 24
07| Idler wheel| 4| A7| Rear side cover ****L| 1| B7| Motor left and right cover| 20
08| Back roll| 1| A8| Rear side cover ****R| 1| B8| Countersunk hex spiral M6*10| 5
09| Front roller| 1| A9| Under the end ****cap L| 1| B9| KB M5*10| 24
10| Heart rate batch-off| 2| A10| Under the end ****cap R| 1| B10| ****Carriage bolts    M10*25| 4
11| Engine room clapboard| 1| A11| Adjusted cap L| 1| B11| ****Flat gasket ∅ 20* ∅ *10.5T1 **| 5
12| Electrical machine| 1| A12| Adjusted cap R| 1| B12| Non-slip nuts M10| 18
13| Motor| 1| A13| Motor cover- top| 1| B13| Cylinder head hex socket ****screws M10*60 half tooth| 1
14| multi-ditches belt| 1| A14| Motor cover- bottom| 1| B14| Cylinder head hex socket ****screws M1045 half tooth| 1
15| Electrical machine dead plate| 1| A15| Motor cover- L| 1| B15| KB M312| 2
16| Running board-bearing housing| 2| A16| Motor- R| 1| B16| Cylinder head socket head**

screw *M10100 （ long >=30 ）**

| 1

17

| Electrical machine fan| ****

1

| ****

A17

| ****

Head cover LED

| ****

1

| ****

B17

| Cylinder head hex socket **screws M10*60 overall  tooth**|

4

18| Power source switch plate| 1| A18| Header cover| 1| B18| Round head hex socket **screws M8*16| 28
19| Running belt| 1| A19| Bottom cover| 1| B19| Round head hex socket ****screws M6*12| 11**

20

| ****

Running board

| ****

1

| ****

A20

| ****

Back cover

| ****

1

| ****

B20

| Cylinder head hex socket **screws**

（ big head ） *M812**

| ****

4

21| Header putaway| 1| A21| Glass box -L| 1| B21| Round head hex socket **screws M6*65| 2**

22

| Heart rate on Pills(stainless steel)| ****

2

| ****

A22

| ****

Glass box-R

| ****

1

| ****

B22

| Cylinder head hex socket **screws**

（ big head ） *M816**

| ****

11

23| Flange bearing ∅ 30| 2| A23| Hand heart tube **L| 1| B23| Cylinder head hex socket ****screws M10*25| 6
24| Transducer| 1| A24| Hand heart tube ****R| 1| B24| Cylinder head hex socket ****screws M8*25| 4
25| Nut card buckle| 4| A25| Heart rate upper piece| 2| B25| Round head hex socket ****screw M10*16| 21
| | | A26| Heat rate lower piece| 2| B26| Round head hex socket ****screw M10*55| 2
| | | A27| Armrest cover L| 1| B27| Cylinder head hex socket ****screws M6*20| 4
| | | A28| The armrest ****covers R| 1| B28| Cylinder head hex socket ****screws M612| 8
| | | A29| Armrest Inside L| 1| B29| Round head hex socket| 4
| | | | | | | screw M630|
---|---|---|---|---|---|---|---|---
| | | A30| Armrest inside R| 1| B30| Round head cross-tapping**

screw *M3.515**

| 12
| | | A31| Armrest front

small cap L

| 1| B31| PWB *M46| 2
| | | A32| Armrest front**

small cap R

| 1| B32| PWB *M48| 4
| | | A33| Armrest cover L| 1| B33| headless socket head**

screw *M850**

| 1
| | | A34| Armrest cover R| 1| B34| Plain nut M8| 1
| | | A35| Armrest bottom

cover L

| 4| B35| Round head hex socket

screws *M1045**

| 3
| | | A36| Armrest bottom

cover R

| 4| B36| Non-slip nuts M3| 2
| | | A37| *3030 pipe**

fastener

| 4| B37| PWB M410| 4
| | | A38| 3030 pipe

fastener

| 4| B38| **Flat gasket ∅ 12* ∅ *5.5T1 **| 4
| | | A39| Flange bearing**

∅ 25

| 2| | |
| | | A40| Running board

small card

| 4| | |
| | | A41| **crash pad| 6| | |
| | | A42| Big plug| 6| | |
| | | A43| STOP key(red)| 1| | |
| | | A44| Small plug| 4| | |
| | | A45| Slight open| 1| | |
| | | A46| | Self- locking**

Push Switch

| | 1| | |
| | | A47| STOP| 1| | |
| foundation ring|
| | | A48| | Heart rate pipe

cushion covers

| | 2| | |

Check and tighten the screws at regular intervals, as they may loosen due to vibrations. Damage that may be caused by a lack of maintenance is not covered by the warranty.

Assembling & Handling Instruction

1. The signal line a and B docking, and then by half round in the six corners Screw B25 (M10*16)through the left and right columns 02 fixed.
2. The signal line connector C, D docking, and then by half round inner six angle screw B25 (M10*16) the 02 column is fixed on a bottom frame 01.
3. Half-round head hexagon screw B7 M512 to left and right motor fixed treadmill main frame 01 front cover. With half-round head hexagon screw B21 M665 through column 02 motor cover about cover locking.
4. With a cylinder head hexagon screw B22 M816 and main frame 01 fixed, then half round head hexagon screw B18 M816 cover and the motor – left cover and the right cover fixed.
5. Put the console top frame (05) at the middle iron plate of the treadmill. Align the hole with the hole, and then use half -round head with an inner hexagon screw M1050（A5） through the iron plate to lock. Then use the half-round head with an inner hexagon screw M1020（A6）to lock with the bottom of the iron plate and use the half-round head with an inner hexagon screw， M10*20（A6）to lock with the bottom of the iron plate.

Align the console end cover (06) with the console top frame (05) and use a Half-round head with an inner hexagon screw M610 (A7).
2) Connect the data cable corresponding to the interface.
3) Place the display screen (07) directly in front of the iron frame, then use round head screw M516（A8）through console end cover 06 to lockthe display.

Position of Electric Outlet and Power Switches

When the power switch is turned to “O”, the electric source is in a state of disconnection. when the power switch is turned to “－”, the electric source is in the state of connection.

Drive belt adjustment

1. During operation, when the running belt has deviated to the left, clockwise adjust the adjustable bolt of the left running belt, or anticlockwise adjust the adjustable bolt of the right running belt; and vice versa. Adjustment method: use the Allen key to adjust the adjustable bolts on the left and right side of the rear protecting cap, to make the running belt in the middle position; accommodation amplitude should not be too large, and 90 degrees each time adjustment is suggested.
2. Adjustment of running belt tightness Adjustment method: run the machine at a low speed, use the Hex key to clockwise adjust the two ‘adjustable bolts of running belts’ at the rear part of the treadmill; accommodation amplitude of two ‘adjustable bolts of running belts’ should be the same, and should not be too large; 90 degrees each time adjustment is suggested. After each adjustment, confirm the tightness of the running belt. Steps are as follows: run the machine at a low speed, and the user holds the front handrail, and steps hard on the running belt, to see if there are pauses; if yes, make the next adjustment; and if not, then there’s no need of adjusting the running belt.

Machine maintenance

1. Great attention should be paid to damageable parts.
2. Change the damaged parts in time. The machine cannot be used unless repaired, and a noticeable nameplate “Being repaired” should be put around the machine.
3. When treadmills have abnormal sounds or won’t operate due to some other reasons, please contact our after-sales service department without delay. Please use original spare parts from the manufacturing company if they need changing, otherwise, the company will not be responsible for the caused loss.

Pulse Testing

Please grasp the front handle of the grip pulse.

1. Before exercise, please stand on both sides of belt. Please hold the sensor of the grip pulse lightly, and after 20 seconds, there will be an exact heart rate to be displayed on the screen.
2. After exercise, the process is the same as it before exercise. please stand on both sides of the belt.

Please hold the sensor of the grip pulse lightly, and after 20 seconds, there will be an exact heart rate to be displayed on the screen.

CAUTION! The heart rate sensor and calorie counter are not medical devices. Several factors can affect the accuracy of the indications. The heart rate sensor is only intended as an aid during exercise to monitor your heart rate in general.

Control Using Instruction Technical parameters

A| Heart rate display/step number| 70-200 / Min when holding heart rate to show heart rate, when the rate is switched to the rate of change (999 steps) to the maximum value of the reset after the reset

step.

---|---|---
B| Gradient| 0-15 %
C| Calories| 0-999 KCAL
D| Program display| The dot matrix displays the selected program；

MANUAL；

| | RANDOM HILL ； 5K LOOP ； ALPINE PASS ； FITNESS TESTS；

TRAINING TOOLS ；

---|---|---
E| Time| 00:00-99:59 Min
F| Speed| 0.0-20.0 km/h
G| Distance| 0.0-99.9KM
H| Incline adjustment| “+” increase gradient “-” decrease gradient； one time

1% adjustment

I| Program selector| Program selection, middle “confirmation” key
J| Pause, start, stop| Control treadmill pause, start, stop
K| ****

Speed adjustment

| “+” speed plus; “-” speed reduction; 0.1KM adjustment
L| Speed     direct     key

keyboard

| 0-9 keyboard input speed value (1-20KM/H); return key

to cancel, “OK” key to confirm

Operation panel description

When the treadmill back power switch electricity, electricity green digital panel treadmill will light up, and in the middle of the “PROGRAM” a green display window welcomes the cycle, said ready.

1. Press the key ,(this is the touch button, as long as the contact can be), the middle “PROGRAM” green display window displays 3 seconds countdown and accompanied by “Di ~ Di ~ ~ ~ ~”…” Buzzer sound, treadmill with to 1KM/H running speed of and a speed display window for “1.0”, said treadmill running speed of 1.0KM/H, and so on.
2. When running press the Key , the treadmill stops running and the Slope remains the same, the speed stops, when the start button is pressed, the state is still in accordance with the suspension before the operation.
3. When running, press the key , said to stop running, slope to return to the level, the speed stops, once again press the start key, then the treadmill runs from speed 1KM/H.
4. When running, press the key ， Can adjust the slope, the slope of the treadmill ranges from 0~15%, a single press, according to the height of the 1% regulation.
5. When running, press the key ， Can adjust the speed value, the speed range is q1KM/H~20KM/H, a single press, only in accordance with the 0.1KM/H speed regulation, hold down a button when the button is not put, for the rapid increase or even decrease, use, please note.
6. PROGRAM” Setting panel： The programming model has 6 kinds of modes, when the normal start of the treadmill, the manual user manual mode, the indicator light on the left side of the instructions in the manual, pressing the up or down arrow can regulate the corresponding mode when the selected mode press the Enter key confirmation. Adjustments must be done in the running machine stopped after the operation is invalid.
7. The numeric keypad on the right side of the speed buttons Press the corresponding numerical, and press the “OK” key speed will be run according to the input value. For example, in the hope that the treadmill running in a speed of 12KM/H, first press the number “1”, according to the number “2”, press the “OK”, and the speed will be adjusted to 12KM/H. If the treadmill is now in operation, speed regulation, if it is not running, when the input, press the start button is operated according to the predetermined speed, pay attention to the speed range is limited to 1~20KM/H input range of other data invalid.
8. When both hands hold the heart rate handle, the heart rate display frame will show the measured value of the heart rate (only for reference), when not holding the handle, will show the number of users on the treadmill exercise, for reference
9. Reciprocal patterns: in the standby mode, press the Enter key, time window flashing, selecting the reciprocal time; again, press the Enter key, flashing from the window, selecting the reciprocal distance; again, press the Enter key, calorie window flashing, select the bottom calories.

Instruction of Training：

1. Please stand on the plastic plates of both sides, then start the machine. At the state of low speed, step on the belt by order.
2. While in exercise, please try every means to keep your feet in the middle of the belt. According to the adjustment of speed, please adjust to the range of steps and frequency. Keep visual ahead, and the hands half-gripped, shaking naturally, breathing evenly.
3. Press the button stop or pause, the machine will be stopped. After the machine recovers to be still totally, put your hands onto the handles of both sides or put your hands onto the front handle, then step onto both plastic plates, finally it is safe to get off the treadmill.
4. While in exercise, if someone feels difficulty breathing, dizzy, or chest pain please stop exercising and consult the instructor immediately.

The material list of packing cartons

CAUTION! During exercise, heavy sweating can cause mechanical and electrical damage to the machine. Like any other liquid substance, sweat can cause damage mainly to the electrical parts of the machine (dial, cables, etc.). The best solution is to use a towel during exercise and wipe the machine after each use to avoid any unwanted damage

LUBRICATION INSTRUCTIONS

WARNING! Always unplug the power cord before performing any maintenance on your treadmill.
CLEANING: Regular cleaning of your treadmill will extend its life.
WARNING! To avoid electric shock, make sure the treadmill is off and the power cord is unplugged before cleaning or maintenance.
AFTER EVERY EXERCISE: Wipe the console and other surfaces of the treadmill with a clean, dry soft cloth to remove excess sweat. DO NOT USE CHEMICALLY.
WEEKLY: The use of a machine-protective floor or mat is recommended for easy cleaning. The dirt from the shoes comes in contact with the moving belt and eventually penetrates the bottom. The use of a vacuum cleaner under the treadmill is recommended once a week.
MONTHLY: put a broom under the treadmill to prevent dirt or trash from accumulating. Once a year, you should remove the black cap of the motor and clean the dirt that may have accumulated in this area.
WOODEN PLATFORM LUBRICATION: Periodic lubrication control of the belt is recommended to ensure the optimal performance of the treadmill. Every 1 month, or 20 – 40 hours of operation, lift the ends of the drive belt and touch the top of the wooden platform as far as your hand can reach. If you feel traces of silicone, you do not need lubrication. If you feel the wooden surface is dry, you need lubrication. Ask your seller or call the technical department for the type of silicone.

HOW TO LUBRICATE THE PLATFORM
Caution: Get the right product for lubricating the drive belt. Do not use grease or anti-rust liquid or any other spray.

1. Put the spray nozzle on the lubrication spray head.
2. While lifting the drive belt on one side, place the spray nozzle between the drive belt and the wooden platform about 10cm from the front of the treadmill. Apply the silicone spray to the wooden platform, moving back and forth. Repeat for the other side of the drive belt. Spray for about 4 seconds on each side.
3. Run the treadmill for 2 minutes at a speed of 5 km / h so that the silicone is spread over the entire wooden surface and then you can use the treadmill normally.

WARNING: Do not over-lubricate the wooden platform. Excess lubricant should be wiped with a clean towel.

WARNING: The contact between the wooden surface of the treadmill and the treadmill plays an important role in the operation and life of the treadmill. We recommend that you keep the treadmill clean and lubricate it frequently, following the instructions for use. Incomplete lubrication causes damage to the belt and electrical parts of the treadmill.

FEATURES

MOTER:| 5.0 hp (Range: AC 3.0 -> 7.0HP)
SPEED RANGE:| 1.0 – 22.0 km/h
INCLINE:| 15 level
BELT:| 160 cm x 57 cm (Thickness: 2.5mm)
WEIGHT:| 200 kg
Ν.W./GW:| 210 / 230kg
MAXIMUM USER WEIGHT:| 180 kg
DIMENSIONS:| L: 222 cm x W: 92.7 cm x H: 160 cm
FOLDING:| Non-Foldable
INPUT VOLTAGE ：| 220V-240V
DISPLAY FEATURES
DISPLAY:| 7 Led Display
DISPLAY INDICATIONS:| Time, Speed, Pulse, Distance, Calories,

Program, User Program, Body Fat

PROGRAMS:| 5-Built-in programs, User Programs, Manual

Programs, Body Fat Program

QUICK SPEED BUTTONS:| Direct speed adjustment keys
QUICK INCLINE BUTTON:| Ν/Α
OTHER FEATURES:| High quality sound system, aluminum

handles, light touch keys

TERMS OF WARRANTY

• The warranty period is 2 years for the motor, 2 years for mechanical, electrical/electronic parts, and 5 years for the metal frame.
• X-TREME STORES S.A. undertakes to repair the machine free of charge in the event of damage due solely to a manufacturing fault. The warranty covers the cost of the spare parts. Replacement of spare parts or not is up to the company technicians. The customer is responsible for the control and adjustment of the machine.
• This warranty note is only valid if it is accompanied by legal proof of purchase (invoice or retail receipt). The warranty period is not extended for any reason and the transfer of it to a third party is excluded.
• Any damage is repaired as soon as possible and any claim for damages due to lack of spare parts and delay in repairing the damage is excluded. The costs of transporting the machine to or from the dealership will be borne by the customer after 6 months of purchase.
• The warranty conditions are set by the manufacturers of machinery and are governed by European regulations.
• Upon expiry of the warranty, any replacement part is covered by a 6-month warranty.

THE WARRANTY SHALL NOT APPLY:

• When the fault is the result of misuse, alterations, poor connection, poor maintenance, and voltage fluctuations in the PPC network.
• Components damaged by user fault such as broken plastic parts, damaged belts with improper adjustment, incorrect or incomplete lubrication, and damage when moving the machine.
• Components such as side pads and cushions are considered consumables and are covered by a 6-month warranty.
• When the machine is opened or repaired by third parties.
• When the damage is caused by the buyer’s negligence & the instructions for use have not been followed.
• When the machine is outdoors or exposed to sun or dust. (Dust and lint on the inside of the machine (motor roller) cause serious damage. Keep the machine clean!).
• When electronic components (console) are damaged by intense sweating or other liquid that has come into contact with or penetrated inside them.
• Tel: 210 66 20 921 -2
• FAX: 210 66 20 923
• e-mail: service@xtr.gr.

Koupi Avenue 34, Koropi P.C. 19441 P.O.Box 6201

• Tel.: 210 66 20 921 -2
• FAX: 210 66 20 923
• E-mail: info@xtr.gr
• f/xtrstores
• /@xtr.gr

Tel for all of Greece:

• 801.11.15.100
• www.xtr.gr.

References

• X-Treme Stores - The Biggest Fitness Family

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>