Trust ACDB-8000AC Plug In Wireless Doorbell Set User Manual

**Trust ACDB-8000AC Plug In Wireless Doorbell Set User Manual

**

ACDB-8000AC PLUG-IN WIRELESS DOORBELL SET

A LED indicator doorbell
B Connect button
C Volume button
D Melody selection
E LED indicator push button
F Push button

Wireless control
The wireless doorbell can be operated wirelessly with a minimum of 1 and a maximum of 32 Trust Smart Home transmitters of your choice. For example, you can play a desired melody using the supplied push button. In addition, you can also play a melody when movement  is detected and / or when a window or door is opened.For each Trust Smart Home transmitter you can set a separate melody to hear exactly whether someone presses the push button or if a door or window is opened.

1. Remove battery strip from push button
   A Insert a flat screwdriver into the notch at the bottom of the push button and slide the push button off the back plate.
   B Open the waterproof rubber by flipping it to reveal the battery.
   C Remove the plastic battery strip.
   D Close the waterproof rubber and place the push button back on the back plate.
   

2. Placing the Receiver
   Place the doorbell in an indoor electrical outlet. If you move the doorbell to another outlet, the connected transmitters will remain in the memory.
   

3. Selecting the desired volume
   First press the volume button to set the desired volume level. There are 4 levels: High, Medium, Low and Off (LED indication only).
   

4. Selecting the desired melody
   Press the melody button to select 1 of the 6 melodies. You can set a separate melody for each transmitter (push button, motion detector, door/window sensor) by selecting it in advance.
   
   5A. Connecting transmitter(s) to the doorbell
   Press the connect button for 1 second to activate the learning mode. The learning mode will be active for 10 seconds and the LED indicator on the doorbell will flash slowly
   

5B
While the LED indicator is flashing, send an ON signal with a Trust Smart Home transmitter to pair it to the doorbell.

5C
As soon as the transmitter is paired, the wireless doorbell will give 2 short beeps. The transmitter, melody and volume are now paired. The wireless doorbell is now ready for use. The receiver can store 32 different transmitters in its memory. If you want to pair several transmitters, repeat steps 2 to 5c
2 short beeps

6A. Securing push button with double-sided tape
Determine where to place the push button and attach the push button with the supplied double-sided tape.


6B. Securing push button with screws

A Insert a flathead screwdriver into the notch on the bottom of the push button and slide the push button off the back plate
B Determine where the push button will be placed and secure the back plate with the supplied screws.
C Place the push button back on the back plate by sliding it from top to bottom.
2 short beeps

Changing the battery of the push button
A When the battery is low, the LED will light up for 2 sec and then blink 3 times after pressing the push button. Insert a flat screwdriver into the notch on the bottom of the push-button and slide the push-button off the back plate.
B Open the waterproof rubber to reveal the battery
C Remove the old battery and insert a new CR2032 battery into the recess of the battery holder. Make sure the + is pointing upwards.
C Close the waterproof rubber and place the push button back on the back plate

Unpair a Trust Smart Home transmitter

2 short beeps

A Press the connect button for 1 second. The learning mode will be active for 10 seconds and the LED indicator on the receiver will blink slowly.
B While the learning mode is active, send an ON signal with the channel of the paired Trust Smart Home transmitter you want to disconnect
C To confirm, the wireless doorbell will give 2 short beeps.

Erasing the entire memory

A Press the connect button (8 seconds) until the LED indicator starts flashing rapidly. The erase mode will be active for 10 seconds and the LED indicator on the receiver will flash rapidly.
B While the delete mode is active, press the learn button again for 1 second to confirm that you want to delete the memory completely
C To confirm, the wireless doorbell give 2 short beeps

Combine the push button with the ICS-2000/ Smart Bridge
Combine the push button with the ICS-2000/Smart Bridge and also receive a push notification on your smartphone when the doorbell rings.

For example, you can turn the wireless plug-in doorbell off at night and only receive a push notification when the push button is pressed.

Safety Instructions

Product support: www.trust.com/71273. Warranty conditions: www.trust.com/warranty To ensure safe handling of the device, follow the safety advice on: www.trust.com/safety The Wireless range is strongly dependent on local conditions such as the presence of HR glass and reinforced concrete Never use Trust Smart Home products for life-support systems. This product is not water-resistant. Do not attempt to repair this product. Wire colors may vary per country. Contact an electrician when in doubt about wiring. Never connect lights or equipment that exceed the maximum load of the receiver. Exercise caution when installing a receiver voltage may be present, even when a receiver is switched off. Maximum radio transmit power: 7.21 dBm. Radio transmission frequency range: 433,92 MHz

Disposal of packaging materials – Dispose of packaging materials which are no longer needed in accordance with applicable local regulations. The packaging materials have been selected for their environmental friendliness and ease of disposal and are therefore recyclable.

Disposal of the device – The adjacent symbol of a crossed-out wheelie bin means that this device is subject to  Directive 2012/19/EU. his directive states that this device may not be disposed of in normal household waste at the end of its usable life, but must be handed over to specially set-up collection locations, recycling depots or disposal companies. This disposal is free of charge for the user.

Disposal of batteries – Used batteries may not be disposed of in household waste. Only dispose of batteries when they are fully discharged. Dispose of batteries according to local regulations. Cover the poles of partially discharged batteries with tape to prevent short circuits.

Trust Electronics Ltd. declares that item number 71273/71273-02 is in compliance with Directive Electromagnetic Compatibility Regulations 2016, Radio Equipment Regulations 2017. The full text of the declaration of conformity is available at the following internet address: www.trust.com/compliance

Trust International B.V. declares that item number 71273/71273-02 is in compliance with Directive 2014/53/EU – 2011/65/EU. The full text of the EU declaration of conformity is available at the following web address: www.trust.com/compliance

Declaration of Conformity

Trust International B.V. declares that this Trust Smart Home-product:
Model: ACDB-8000AC Plug-in wireless doorbell set
Item number: 71273/71273-02
Intended use : Indoor

is in compliance with the essential requirements and other relevant provisions of the following directives:

ROHS 2 Directive (2011/65/EU)
RED Directive (2014/53/EU)

The full text of the EU declaration of conformity is available at the following web address: www.trust. com/compliance

TRUST SMART HOME
LAAN VAN BARCELONA 600
3317DD DORDRECHT
NEDERLAND
www.trust.com

Trust Electronics Ltd.,
Sopwith Dr, Weybridge, KT13 0NT, UK.
All brand names are registered trademarks of their respective owners.
Specifications are subject to change
without prior notice. Made in China.

TECHNICAL SPECIFICATIONS Doorbell

References

• Trust.com - Contact & Support - Compliance
• Trust.com - Home
• Trust.com - Home
• Trust.com - Wireless Doorbell with plugin chime ACDB-8000AC
• Trust.com - Contact & Support - Compliance
• Trust.com - Contact & Support - Safety information
• Trust.com - Contact & Support - Warranty conditions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>