PERKP 0647DP0CHR Navigation Lights LED Horizontal Mount Bi Color Light User Manual
- June 13, 2024
- PERKP
Table of Contents
PERKP 0647DP0CHR Navigation Lights LED Horizontal Mount Bi Color Light
Product Information
- Visibility: 2nm
- Product Name: Cat. No. 0647 Series LED Bi-Color Lights
- Product Name: Cat. No. 0648 Series LED Side Lights
- Designed for: Power-driven vessels under 20 meters (65.6 ft.) in length operating on a nominal 12 Voltsystem
- Compliance: ABYC C-5, A-16, EN/ISO 19009:2015, the ’72 COLREGS, and the U.S. Inland Rules
Product Usage Instructions
- For proper light selection, positioning, and configuration, refer to the ABYC C-5, A-16, EN/ISO 19009:2015 Standards, A.B.Y.C., the ’72 COLREGS, and the U.S. Inland Rules.
- Mount the lights on a horizontal surface.
- Draw a 6-inch long reference line through the center of the selected mounting location and parallel to the centerline of the boat.
- Cut out the mounting template. Place it on the mounting surface so that the reference line (drawn above) aligns with the reference line marked on the template.
- Drill 2 holes through the template to accommodate #6 pan or round head mounting screws. Drill a 7/16-inch hole for electric wiring.
- Attach supply connections to the light, following A.B.Y.C. Standard E-11 and U.S. Coast Guard Safety Standards for Boat Electrical Systems (33 CFR 183). Observe polarity.
- Mount the light according to the template. Align the thin reference marks on the outside of the base with the reference line drawn in Step #3 for accurate mounting orientation.
- Note that these lights are supplied complete with 12 Volt LEDs and do not have user-serviceable components.
OVERVIEW
The above-referenced Standards can be obtained from:
- American Boat & Yacht Council, Inc
- U.S. Coast Guard 613 Third Street, Suite 10 Washington D.C. 20593 Annapolis, MD 21403 (or your local C.G. office)
For more information, visit the manufacturer’s website: www.perko.com
- Cat. No. 0647 Series LED Bi-Color Lights
- Cat. No. 0648 Series LED Side Lights
These lights are designed for use on power-driven vessels under 20 meters (65.6 ft.) in length operating on a nominal 12 Volt system. In order to comply with ABYC C-5, A-16, EN/ISO 19009:2015, the ‘72 COLREGS and the U.S. Inland Rules, the following must be adhered to:
MOUNTING INFORMATION
Read all instructions before proceeding
- For proper light selection, positioning and configuration, refer to the ABYC C-5, A-16, EN/ISO 19009:2015 Standards, A.B.Y.C., the ‘72 COLREGS, and the U.S. Inland Rules.
- These lights are designed to be mounted on a horizontal surface.
- Draw a 6-inch long reference line through the center of the selected mounting location and parallel to the centerline of the boat.
- Cut out the mounting template. Place it on the mounting surface such that the reference line (drawn above) is directly underneath the reference line marked on the template.
- Drill 2 holes through the template to accommodate #6 pan or round head mounting screws. Drill a 7/16-inch hole to accommodate the electric wiring.
- Attach supply connections to the light, making sure to wire by both A.B.Y.C. Standard E-11 and U.S. Coast Guard Safety Standards for Boat Electrical Systems (33 CFR 183). Observe polarity.
- Mount the light following the template. Note that there are thin reference marks on the outside of the base that must be aligned with the reference line (drawn in Step #3) for the final accuracy of mounting orientation.
- These lights are supplied complete with 12-volt LED’s. There are no user-serviceable components.
The above-referenced Standards can be obtained from:
- American Boat & Yacht Council, Inc 613 Third Street, Suite 10 Annapolis, MD 21403
- U.S.CoastGuard Washington D.C. 20593 (or your local C.G. office)
- International Standards Organization (ISO) Ch. de Blandonnet 8 • CP 4 CH-1214 Vernier, Geneva, Switzerland
PERKO, Inc. 16490 N.W. 13th Avenue Miami, Florida 33169-5707 www.perko.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>