AiPi CAM-D200 Camera Core Board User Guide

AiPi CAM-D200 Camera Core Board

Product Information

• Specifications:
  • Product Name: AiPi-CAM-D200
  • Functionality: USB Camera with SD Card Support and LED Light Function
  • Camera: DVP camera connected through FPC socket
  • Wireless Connectivity: Hotspot with SSID: ai_pi_cam, Password: 12345678
  • Web Interface: Accessible at 192.168.169.1 for camera streaming
  • Image Format: JPG
  • SD Card Support: Yes, for storing captured images
  • LED Light Function: Activated by pressing the S2 (Boot) button for 2 seconds

Product Usage Instructions

• USB Camera Input:
  • DVP camera is connected through an FPC socket.
• Power On and Camera Streaming:
  • Power on the device.
  • Connect your phone or computer to the hotspot named “ai_pi_cam” using password “12345678”.
  • Open a web browser and enter the address 192.168.169.1.
  • Click on “Start Stream” to view the camera image.
• Taking Pictures:
  • To take a picture and save it to the SD card:
  • Insert the module’s SD card.
  • Press the S2 (Boot) button to take a picture.
  • The image will be saved as a JPG file on the SD card with sequential numbering.
• Viewing Captured Images:
  • To view the saved pictures:
  • Remove the SD card from the module.
  • Use a card reader to access the SD card contents.
  • You can see the saved pictures on the SD card.
• LED Light Function:
  • To use the LED light function:
  • Press and hold the S2 (Boot) button for about 2 seconds to turn on the flashlight.
  • Repeat the operation to turn off the LED light.
• Serial Port Information:
  • The serial port will print corresponding information for monitoring purposes.

FAQs

• Q: How do I access the camera stream?
  • A: Connect to the hotspot, open a web browser, and enter 192.168.169.1 to start streaming.
• Q: What is the image format for captured pictures?
  • A: The images are saved in JPG format on the SD card.
• Q: How do I activate the LED light function?
  • A: Press and hold the S2 (Boot) button for 2 seconds to turn on the LED light.

PRODUCT OVERVIEW

Firmware burning

1. Serial port wiring
2. Burning
   • Burning tool download：Click to download.
   • Firmware address： Click to check.
   • After the burning tool starts burning, first press and hold the “Download Button”, then press the “Reset
   • Button” and then release it, to enter the burning mode.
   • The steps are as follows:

Usage steps

1. USB camera input
   • DVP camera is connected through an FPC socket
2. Usage steps
   • Power on, use your phone or computer to connect to the hotspot: ai_pi_cam, password: 12345678
   • Open the web page and enter the website 192.168.169.1, click Start Stream, and see if there is a camera image, as shown below：
   • When the module is inserted into the SD card, it supports the camera function.
   • You can take a screenshot of the current page and save it to the SD card. The image format is JPG.
   • The method of taking pictures is to press the S2 (Boot) button.
   • The pictures will be saved to the SD card and named with numbers, starting from 0.
   • Here are some photos of little yellow ducks, as shown below:
   • Remove the module’s SD card and use a card reader to read the contents of the SD card.
   • You can see that the pictures have been saved to the SD card.
   • The renderings of the shooting：
   • The module is also equipped with an LED light function. Press and hold the S2 (Boot) button for about 2 seconds and release it to turn on the flashlight function.
   • Repeat the operation to turn it off. Results as shown below:
   • The serial port will also print the corresponding information：

Documents / Resources

| AiPi CAM-D200 Camera Core Board [pdf] User Guide
CAM-D200 Camera Core Board, CAM-D200, Camera Core Board, Core Board, Board
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>